BEGA 24 065 Recessed Wall Luminaire Instruction Manual

: June 12, 2024
: BEGA

Table of Contents

BEGA 24 065 Recessed Wall Luminaire
DIMENSION
Instructions for use
Product Description
Overvoltage protection
Safety
Installation
Cleaning · Maintenance
Accessories
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 24 065 Recessed Wall Luminaire

BEGA-24-065-Recessed-Wall-Luminaire-PRODUCT

DIMENSION

BEGA-24-065-Recessed-Wall-Luminaire-FIG-1

Instructions for use

Application
Surface washer with asymmetrical flat beam light distribution, for flush or surface mounting installation. Recessed wall luminaire for the spatial illumination of ground surfaces from a very low mounting height.

Product Description

Luminaire made of aluminum alloy, aluminum and stainless steel
BEGA Tricoat® coating technology
Safety glass with optical structure
Reflector made of pure anodised aluminum
Fixing is achieved by using two adjustable wedge-shaped claws
Required recessed opening 306 x 60 mm
Recessed depth 70 mm
2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm
Connection terminal 2.5@
Earth conductor connection
LED power supply unit
220-240 V x 0/50-60 Hz
DC 170-280 V
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK06
Protection against mechanical impacts < 1 joule
r – Safety mark
c – Conformity mark
Weight: 0.9 kg
This product contains light sources of energy efficiency classes D

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547. To achieve additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Lamp

Module connected wattage 8.7 W
Luminaire connected wattage 11 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 40 °C
When installed in heat-insulating
material ta max = 30 °C

24 065 K3

Module designation LED-0742/830
Color temperature 3000 K
Color rendering index CRI > 80
Module luminous flux 1350 lm
Luminaire luminous flux 557 lm
Luminaire luminous efficiency 50,6 lm / W
24 065 K4
Module designation LED-0742/840
Colour temperature 4000 K
Colour rendering index CRI > 80
Module luminous flux 1365 lm
Luminaire luminous flux 563 lm
Luminaire luminous efficiency 51,2 lm / W

Please note:
This luminaire is coated with BEGA Tricoatb. BEGA Tricoatb is a registered trademark for a technology that we use to achieve optimal corrosion resistance. Even the best possible surface protection and the highest corrosion resistance can be rendered almost ineffective in some cases by aggressive media caused by leaching of building materials.Where such media are suspected, a material analysis must be carried out before installation. Always avoid excessive use of chemical cleaning agents in the vicinity of the luminaire.

Installation

The recessed opening will be covered by the frame of the luminaire housing. Fixing of the luminaire is achieved by using two adjustable wedge-shaped claws.
Installation in solid, plastered walls:
The installation housing 10 426 is available for this purpose. If this is not used, an exact recessed opening of 306 x 60 mm with a minimum depth of 70 mm is required.
Installation in exposed brickwork:
The construction of an on-site recessed opening with the exact installation dimensions of 306 x 60 mm with a minimum depth of 70 mm is required. An installation housing cannot be used.
Installation in drywalling:
A recessed opening of 306 x 60 mm with a minimum depth of 70 mm is required. The claws grip behind drywall.
Installation into insulated façades:
For installation in EWIS external wall insulation systems please use installation housing 13 521 in combination with a plaster frame 10 026 or 13 505.
Open luminaire:
Undo the screws and remove the housing cover. Disconnect the plug-connection of the LED connecting cable. Disconnect the earth conductor connection from the plug connection. Lead the mains supply cable through the cable entry into the luminaire housing. Make earth conductor connection. Push silicone sleeves over the lines and make an electrical connection. In order to guarantee the maximum service life of the electrical components, the enclosed desiccant pouch must be placed in the luminaire. Remove the desiccant pouch from the foilpackaging and place it in the position marked by the red information label immediately before finally closing the luminaireConnect the LED connection cable by means of a plug connector. Put on earth conductor connection of the housing cover. Assemble the housing cover. Make sure that gasket is positioned correctly. Tighten the screws evenly. Insert luminaire housing into the recessed opening. Tighten screws of the claw fastener evenly.

Cleaning · Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high-pressure cleaners.

Replacing the LED module

The designation of the LED module is noted on a label in the luminaire.
The light color and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
The defective glass must be replaced.
Close the luminaire.