MINKA LAVERY 2869-66A Sheer Elegance Linear Pendant Chandelier Instruction Manual

MINKA LAVERY 2869-66A Sheer Elegance Linear Pendant Chandelier

Product Information

The product being referred to is item#2869-66A, which is a new model released on May 26, 2022. The installation instructions provided in the user manual are for this specific item.

Product Usage Instructions

WARNING: Before starting the installation process, make sure to shut off the power at the fuse box or circuit breaker box to prevent any electrical hazards.

Preparing for Installation:

1. Refer to Figure 1 (illustration) for a visual representation of the installation process. Note that the illustration may not be identical to the actual fixture purchased.
2. Gather the following components: Mounting Plate (Set#A-021-432118), Ground Screw, Mounting Screw (2x).

Fixture Wiring:

• Black or Smooth Wires: These are the wires specific to the fixture.
• White or Ribbed Wires: These are also fixture wires but are identified by their white or ribbed insulation.
• Bare Copper Wires (Ground): These are the fixture’s grounding wires.

House Wiring:

• Black Wires (Hot): These are the hot wires from the house electrical system.
• White Wires (Neutral): These are the neutral wires from the house electrical system.
• Green Wires (Ground): These are the grounding wires from the house electrical system.

Refer to Figure 2 for a visual representation of the fixture components:

Please note that the usage instructions for the product beyond the installation process are not provided in the given textextract. For detailed usage instructions, please refer to the complete user manual.

WARNING ! SHUT POWER OF FAT FUSE OR CIRCUIT BREAKER .

PREPARING FOR INSTALLATION

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

3. Secure rod (J) onto all thread (I) on the fixture body.

4. Determine the desired hanging height and thread rods (F1, F2 and F3) to all thread on rod (J). Screw loop (H1) onto rod (F1). Pass the wires carefully through each rod as you assemble.

5. Attach quick link (G) to loop (H1) and loop (H2) on canopy (E). Carefully feed the wire through loop (H1), quick link (G), and loop (H2).

6. Loosening screws (K) to remove mounting plate (C) from canopy (E). Position mounting plate (C) on the ceiling and mark location of the two mounting holes forplastic anchors (A). Drill the appropriate size holes on the ceiling and insert plastic anchors (A).

7. Attach mounting plate (C) to the junction box, not included, using mounting screws (B) (Size: #8-32N*L0.5”). The side of the mounting plate (C) marked “GND” must face out.

8. Secure mounting plate (C) by screwing wood screws (D) through the holes on mounting plate (C) into plastic anchors (A).

9. The support cable is provided to support the weight of the fixture while wiring. Align the fixture to mounting plate (C) and attach hook (P) on the end of support cable (O) and a slot located on mounting plate (C). Carefully allow the support cable (O) to support the weight of the fixture while wiring.
   CONNECTING THE WIRES (Fig. 2)

10. Connect the electrical wires as shown in figure 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to
    the mounting plate (C) using the green screw provided.

11. Tuck the wire connectors neatly into the junction box.
    COMPLETING THE INSTALLATION (Fig. 1)

12. Place canopy (E) over mounting plate (C) and secure with screws (K).

13. Place candle covers (N) over sockets (L).

14. Install (10) ten candelabra base bulbs (M) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOTEXCEED THE MAXIMUM WATTAGE RATING!
    Your installation is now complete. Return power to the junction box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>