CRYSTORAMA 526-SA Palla 4 Light 24 inch Antique Silver Bathroom Vanity Wall Light Instruction Manual
- June 12, 2024
- CRYSTORAMA
Table of Contents
- CRYSTORAMA 526-SA Palla 4 Light 24 inch Antique Silver Bathroom Vanity
- Product Information
- Product Usage Instructions
- Product Crystal Sets
- Capiz Shell Sets
- Product Parts Included
- ASSEMBLY INSTRUCTION MODEL #526-SA
- Dimensions
- How to install the mounting plate
- Crystal Sets
- PART NUMBER
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CRYSTORAMA 526-SA Palla 4 Light 24 inch Antique Silver Bathroom Vanity
Wall Light
Product Information
Model Number: 526-SA
Manufacturer: Crystorama.com
Dimensions:
A: 24 inches
B: 3.375 inches
C: 6.75 inches
D: 3.375 inches
Bulb Type: Candelabra Base Bulb
Recommended Wattage: 40 Watts
Maximum Wattage: 60 Watts
Usage: Damp Rated
Product Usage Instructions
- How to install the mounting plate:
- Put the mounting plate over the outlet box and mark two points on the wall at the center of key holes.
- Drill the holes at the marked points and insert the wall anchor inside the hole drilled.
- Place the mounting plate over the outlet box and secure it with the machine screws.
- Insert the wall anchor screws inside the wall anchors in the wall and tighten it.
- How to install:
- Remove the frame by unscrewing the nuts on top of the backplate.
- Insert recommended bulbs (not included).
- Secure the frame by screwing the nuts.
Product Crystal Sets
- A: 10 Pieces – 50mm
- B: 11 Pieces – 40mm
Capiz Shell Sets
- C: 31 Pieces – 40mm
- D: 18 Pieces – 30mm
Product Parts Included
- A: (1) – Mounting Hardware
- (1) – Mounting Plate
- (2) – Wall Anchors
- (2) – Anchor Screws
- (2) – Machine Screws
- (3) – Wire Nuts
- B: (2) – Ball Nut1
- C: (2) – Hex Nut
- D: (1) – Backplate(L22.91,H4.72,D0.79) #XRE526SABKP22.91IN
- E: (2) – Ball Nut2
- F: (1) – Frame
ASSEMBLY INSTRUCTION MODEL #526-SA
warning
- All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes.
- You will need 4-Candelabra Base Bulb 40 Watts Recommended 60 Watts Max.
- USE LED BULBS FOR EXTENDED USE THIS FIXTURE IS DAMP-RATED.
Dimensions
How to install the mounting plate
- Put the mounting plate over the outlet box and mark two points on the wall at the center of the keyholes.
- Drill the holes at the marked points and insert the wall anchor inside the hole drilled.
- Place the mounting plate over the outlet box and secure it with the machine screws. Insert the wall anchor screws inside the wall anchors in the wall and tighten it.
How to install
- Remove the frame by unscrewing the nuts on top of the backplate.
- Insert recommended bulbs (not included).
- Secure the frame by screwing the nuts.
Crystal Sets
- A. 10 Pieces 50mm
- B. 11 Pieces 40mm
Capiz Shell Sets
- C. 31 Pieces 40mm
- D. 18 Pieces 30mm
WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and/or birth defects or reproductive harm. For more information go to www.P65Warnings.ca.gov.
PART NUMBER
PART NUMBER MODEL #526-SA
- A. (1) – Mounting Hardware Includes:
- (1) – Mounting Plate
- (2) – Wall Anchors
- (2) – Anchor Screws
- (2) – Machine Screws
- (3) – Wire Nuts
- B. (2) – Ball Nut1
- C. (2) – Hex Nut
- D. (1) – Backplate(L22.91″, H4.72″,DO.79″) #XRE526SABKP22.91IN
- E. (2) – Ball Nut2
- F. (1) – Frame
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>