CRYSTORAMA EMO-5407-BF Emory 6-Light Black Forged Chandelier

Product Information

This is the assembly instruction for the Cryst Rama Model#EMO-5407-BF, a 5” side view lighting fixture that has been lighting the way for sixty years. The fixture is damp-rated and requires 6 candelabra base bulbs with a recommended wattage of 40 watts and a maximum of 60 watts. LED bulbs are recommended for extended use. The product comes with mounting hardware, a mounting plate, mounting screws, a canopy (W5”xL27-1/2”xH3/4” #XRF5407BFCAN5IN), a chain (L72”, 3.8mm thick #XRF5407BFCHA3.8MM), stems (W1/2”xL12-3/4”

XRF5407BFROD12.75IN), a banding ring (#XRF5407BFRING), sockets, and glass

drops (W1”xL7-7/8”). This product can expose you to Lead which is known to the state of California to cause cancer and/or birth defects or reproductive harm. For more information go to www.P65Warnings.ca.gov

Product Usage Instructions

1. Turn off the power before installation.
2. Feed the wires through the stem and slip the down rod along the wire. Thread the down rod onto the nipple on top of the frame.
3. Place the mounting plate over the outlet box and mark four points on the ceiling at the center of the keyhole on the mounting plate.
4. Drill four holes at the marked points and insert the wall anchors.
5. Place the mounting plate over the outlet box and secure it with two outlet box screws. Insert the anchor screws into the wall anchors (installed in step #3) and tighten them.
6. Determine the preferred hanging height and adjust the chain accordingly.
7. Install the canopy onto the mounting plate and secure it with the mounting screws.
8. Hang the glass drops to the banding ring.
9. Install the bulbs (not included) into the sockets.

WARNING

All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes.
You will need 6- Candelabra Base Bulb 40 Watts Recommended 60 Watts Max. USE LED BULBS FOR EXTENDED USE This fixture is Damp rated

How to install

1. Feed the wires through the stem. Slip the down rod along the wire and thread it onto the nipple on top of the frame.
2. Place the mounting plate over the outlet box. Mark four points on the ceiling at the center of the keyhole on the mounting plate.
3. Drill four holes at the marked points and insert the wall anchors.
4. Place the mounting plate over the outlet box and secure it with two outlet box screws. Insert the anchor screws into the wall anchors (Installed in step #3) and tighten.
5. Determine the preferred hanging height and adjust to the chain required.
6. Install the canopy onto the mounting plate, and secure it with the mounting screws.
7. Hang the glass drop to the banding ring.
8. Install the bulbs(not included) into the socket.

Part Number

Part Numbers

• A. (1)-Mounting hardware
• B. (1)-Mounting plate
• C. (6)-Mounting screw
• D. (1)-Canopy W5’’xL27-1/2’’xH3/4’’ #XRF5407BFCAN5IN
• E. (1)-Chain -L72’’, 3.8mm thick #XRF5407BFCHA3.8MM
• F. (2)-Stem W1/2’’xL12-3/4’’ #XRF5407BFROD12.75IN
• G. (1)-Banding ring #XRF5407BFRING
• H. (6)-Socket
• I. (102)-Glass drop W1’’xL7-7/8’’

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>