MINKA LAVERY 4041-84 Acacia 5 Inch 1-Light Brushed Nickel Vanity Light Instruction Manual
- June 12, 2024
- MINKA LAVERY
Table of Contents
MINKA LAVERY 4041-84 Acacia 5 Inch 1-Light Brushed Nickel Vanity Light
Product Information
The product is a light fixture with item number 4041-84. It comes with a mounting plate, ground screw, mounting screws, body, glass shade, metal rings, and a medium base (E26) bulb. The fixture can accommodate up to 60 watts each or CFL or LED equivalent bulbs. The installation manual includes instructions for mounting the fixture, connecting the wires, and finishing the installation.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker and remove the old fixture included the mounting hardware.
- Unpack the new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary for installation.
- Place the mounting plate over the outlet box and align the mounting slots of the plate with mounting holes of the outlet box. Use a level to make sure the plate is straight. Feed the mounting screws through the slots on the plate and into the holes of the outlet box. Make sure the side of the mounting plate marked GND must face out.
- Connect the electrical wires as shown in Fig.2, making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. Tuck wire connections neatly inside the outlet box.
- Thread fixture screws through body and into mounting plate to secure fixture body.
- Place glass shade over sockets and secure it using metal rings.
- Install one medium base (E26) bulb up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
- Turn on power and test the fixture.
Note : The illustration in the manual is for installation purposes only and may or may not be identical to the fixture purchased.
Item #4041-84 (New. 05/18/2021)
READ AND SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
MOUNTING THE FIXTURE
-
Shut off power at the fuse box or circuit breaker and remove the old fixture included the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary for installation.
-
Place mounting plate (B) over the outlet box (A) (Not included) and align mounting slots of mounting plate (B) with mounting holes of outlet box (A). Use a level to make sure mounting plate (B) is straight. Feed mounting screws (C) through mounting slots on mounting plate (B) and into mounting holes of outlet box (A). Make sure the side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES
-
Connect the electrical wires as shown in Fig.2, making sure that all wire connectors (D) are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw provided.
-
Tuck wire connections neatly inside the outlet box.
FINISHING THE INSTALLATION -
Thread fixture screws (F) through body (E) and into mounting plate (B) to secure fixture body (E).
-
Place glass shade (G) over sockets and secure glass shade (G) using metal rings (H).
-
Install (1) one medium base (E26) bulb (I) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).Your installation is now complete. Return power and test the fixture.
Note : Illustration (Fig.1) on this manual is for installation purposes
only. It may or may not be identical to the fixture purchased.
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>