MINKA LAVERY 4046-84 6-Light Brushed Nickel Candlestick Chandelier Instruction Manual

MINKA LAVERY 4046-84 6-Light Brushed Nickel Candlestick Chandelier

Product Information

The product being installed is item #4046-84, with a release date of 06/25/2021. This product is a light fixture that requires wiring and installation. The installation process involves connecting the electrical wires, securing the wire connections, installing the fixture screws, placing the glass shade, and installing the bulbs.

The fixture is designed to use (6) six medium base (E26) bulbs with a maximum wattage of 60 watts each. CFL or LED equivalent bulbs can also be used but are not included in the package. The fixture specification should be followed to avoid exceeding the maximum wattage rating.

Product Usage Instructions

Before beginning the installation process, ensure that the power source is turned off by shutting down the fuse or circuit breaker.

Connecting the Wires

1. Connect the electrical wires according to Fig.3. Ensure that all wire connectors (D) are secured.
2. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw provided.
3. Tuck wire connections neatly inside the outlet box (A).

Finishing the Installation

4. Thread fixture screws (F) through canopy (E) and into mounting plate (B) and secure.
5. Place glass shade (K) over socket cups (J). Secure glass shade (K) using metal rings (L).
6. Install (6) six medium base (E26) bulbs (M) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

Once the installation is complete, return power and test the fixture. Note that the illustration in Fig.1 may differ from the actual fixture purchased.

INSTALLATION INSTRUCTIONS

Item#4046-84 (New. 06/25/2021)

READ AND SAVE THESE INSTRUCTIONS

WARNING ! SHUT POWER OFF AT FUSE OR CIRCUITBREAKER .

MOUNTING THE FIXTURE (Fig.1)

1. Shut off power at the fuse box or circuit breaker and remove the old fixture included the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary for installation.

3. Adjust position of each lamp arm. (As shown in Fig.2)

4. Place mounting plate (B) over outlet box (A) (Not included) and align mounting slots with mounting holes of outlet box (A). Feed mounting screws (C) through mounting slots of mounting plate (B) and mounting holes of outlet box (A). Make sure the side of the mounting plate (B) marked “GND” must face out.

5. Determine desired hanging height and thread rods (I1 and I2) to the all thread of the fixture body. Screw loop (H1) onto rod (I1). Pass wires carefully through each rod as you assemble.

6. Attach quick link (G) to loop (H1) and loop (H2) on canopy (E). Carefully feed wire through loop (H1), quick link (G), and loop (H2).
   CONNECTING THE WIRES (Fig.3)
   

7. Connect the electrical wires as shown in Fig.3, making sure that all wire connectors (D) are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw provided.

8. Tuck wire connections neatly inside the outlet box (A).
   FINISHING THE INSTALLATION (Fig.1)
   

9. Thread fixture screws (F) through canopy (E) and into mounting plate (B) and secure.

10. Place glass shade (K) over socket cups (J). Secure glass shade (K) using metal rings (L).

11. Install (6) six medium base (E26) bulbs (M) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

Fig.1
Set# A-016

1. Mounting Plate
2. Ground Screw
3. Mounting Screw*2

Your installation is now complete. Return power and test the fixture.

Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>