Minka Lavery 2957-572 Upham Estates 8 Light Coal and Polished Nickel Square Pendant Instruction Manual

Minka Lavery 2957-572 Upham Estates 8 Light Coal and Polished Nickel

Square Pendant

Product Information

The product is Item#2957-572, manufactured on August 18, 2021.
It is a light fixture that can accommodate eight candelabra base bulbs with a maximum wattage of 60 watts each. The fixture includes a mounting plate (A), ground screw, mounting screw (x2), cloth shade (G), metal washer (E), rod (L), canopy (C), candle covers (J), and three rods (F1, F2, and F3) to adjust the hanging height. The product comes with installation instructions.

Product Usage Instructions

1. Before installation, turn off power at the fuse box or circuit breaker box.
2. Remove the old fixture and mounting hardware.
3. Unpack the new fixture and lay out all the parts in a clean area. Place the cloth shade (G) and metal washer (E) over all thread (H) and secure rod (L) onto all thread (H).
4. Determine the desired hanging height and thread rods (F1, F2, and F3) to the all thread on rod (L). Screw canopy (C) onto rod (F1). Pass the wires carefully through each rod as you assemble.
5. Attach mounting plate (A) to the junction box with mounting screws (B) (Size: #8-32N*L0.5). The side of the mounting plate (A) with GND marked on it and two convex points must face out.
6. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
7. Tuck the wire connectors neatly into the junction box.
8. Slide canopy (C) over mounting plate (A) and secure with screws (D).
9. Place candle covers (J) over sockets (I).
10. Install eight candelabra base bulbs (K) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
11. Once the installation is complete, turn on power at the fuse box or circuit breaker box and test the fixture.

Note: The illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

INSTALLATION INSTRUCTIONS

Item#2957-572 (New. 2021/08/18)
READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIR CUIT BREAKE  .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARATION (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

3. Place cloth shade (G) and metal washer (E) over all thread (H). Secure rod (L) onto all thread (H).

4. Determine the desired hanging height and thread rods (F1, F2 and F3) to the all thread on rod (L). Screw canopy (C) onto rod (F1). Pass the wires carefully through each rod as you assemble.

5. Attach mounting plate (A) to the junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5”).
   The side of the mounting plate (A) with “GND” marked on it and two convex points must face out. CONNECTING THE WIRES (Fig. 2)

6. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.

7. Tuck the wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1)

8. Slide canopy (C) over mounting plate (A) and secure with screws (D).

9. Place candle covers (J) over sockets (I).

10. Install (8) eight candelabra base bulbs (K) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
    Your installation is now complete. Return power to the junction box and test the fixture.
    Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>