Minka Lavery 2894-691 Pullman Junction 29 Inch 4 Light Brushed Nickel and Coal Vanity Light Instruction Manual
- October 30, 2023
- MINKA LAVERY
Table of Contents
Minka Lavery 2894-691 Pullman Junction 29 Inch 4 Light Brushed Nickel and
Coal Vanity Light
Product Information
Item#2894-691
The product is a fixture that requires installation. The package includes mounting hardware, a mounting plate, screws, drywall anchors, candelabra base bulbs (not included), and glass shades. The fixture is compatible with CFL or LED equivalent bulbs up to 60 watts each. The fixture has three wires – black or smooth, white or ribbed, and green or bare copper for the ground. The product is designed to be mounted on a wall and connected to a junction box.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
- Carefully unpack the new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
- Loosen screws (E) to remove mounting plate (A) from fixture body (F).
- Position mounting plate (A) on the wall, and mark the location of two drywall anchors (B). Pre-drill the holes for the drywall anchors (B). Insert the drywall anchors (B) into the wall.
- Attach the mounting plate (A) to the junction box (not included) using the mounting screws (D). The side of the mounting plate (A) marked GND must face out.
- Screw woodscrews (C) through the holes into the drywall anchor (B) to secure the mounting plate (A).
- Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. After the wires are connected, tuck them carefully inside the junction box.
- Slide fixture body (F) over mounting plate (A) and secure with screws (E).
- Install (4) four candelabra base bulbs (H) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. Do not exceed the maximum wattage rating.
- Screw glass shades (I) onto socket cups (G).
- Turn on power and test the fixture.
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
INSTALLATION INSTRUCTIONS
MOUNTING THE FIXTURE (Fig.1)
- Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
- Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
- Loosen screws (E) to remove mounting plate (A) from fixture body (F).
- Position mounting plate (A) on the wall, and mark the location of two drywall anchors (B). Pre-drill the holes for the drywall anchors (B). Insert the drywall anchors (B) into the wall.
- Attach the mounting plate (A) to the junction box (not included) using the mounting screws (D). The side of the mounting plate (A) marked “GND” must face out.
- Screw woodscrews (C) through the holes into the drywall anchor (B) to secure the mounting plate (A) as shown in Fig.1.
- CONNECTING THE WIRES (Fig. 2)
- Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. After the wires are connected, tuck them carefully inside the junction box.
- FINISHING THE INSTALLATION (Fig.1)
- Slide fixture body (F) over a mounting plate (A) and secure with screws (E).
- Install (4) four candelabra base bulbs (H) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification.
- DO NOTEXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
- Screw glass shades (I) onto socket cups (G).
Your installation is now complete. Return power and test the fixture.
Note: The illustration (Fig.1) in this manual is for installation
purposes only. It may or may not be identical to the fixture purchased.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>