MINKA LAVERY 2543-726 Baldwin Park 3-Light Coal and Soft Brass Cage Pendant Installation Guide

MINKA LAVERY 2543-726 Baldwin Park 3-Light Coal and Soft Brass Cage

Pendant

Product Information

The Item#2543-726 is a new product that comes with installation instructions. It is a fixture designed for indoor use and requires a power source. The fixture includes a mounting plate, canopy, glass shade, metal cover, metal tube, thread, hex nut, quick link, loop, and rods. The fixture can hold three medium base bulbs with a maximum wattage of 60 watts each or CFL or LED equivalent.

Product Usage Instructions

Before installing the fixture, make sure to shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware. Follow the steps below to install the fixture:

1. Carefully unpack your new fixture and lay out all the parts in a clean area.
2. Thread all thread (K) to coupling (L) and tighten with hex nut (N).
3. Place metal tube (M) and metal cover (C) over all thread (K).
4. Place glass shade (I) over metal plate (O).
5. Determine desired hanging height and thread rods (F1, F2 and F3) to all thread (K) of fixture body. Screw loop (H1) onto rod (F1). Carefully pass wires through each rod as you assemble.
6. Attach quick link (G) to loop (H1) and loop (H2) on the canopy (D). Carefully feed wire through loop (H1), quick link (G), and loop (H2).
7. Attach mounting plate (A) to junction box with mounting screws (B). The side of the mounting plate (A) marked with GND and two convex points must face out.
8. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
9. Slide canopy (D) over mounting plate (A) and secure with screws (E).
10. Install (3) three medium base bulbs (J) up to 60 watts each or  CFL or LED equivalent (not included) in accordance with the fixture specification — DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
11. Return power to the junction box and test the fixture.

Note: The illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

INSTALLATION INSTRUCTIONS
Item#2543-726 (New. 02/18/2022)
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT POWER OFF AT FUSE OR CIRCUITBREAKER .

Assembly Instruction

PREPARATION (Fig.1 &Fig. 3) 

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

3. Thread all thread (K) to coupling (L) and tighten with hex nut (N).

4. Place metal tube (M) and metal cover (C) over all thread (K).

5. Place glass shade (I) over metal plate (O).

6. Determine desired hanging height and thread rods (F1, F2 and F3) to all thread (K) of fixture body. Screw loop (H1) onto rod (F1). Carefully pass wires through each rod as you assemble.

7. Attach quick link (G) to loop (H1) and loop (H2) on the canopy (D). Carefully feed wire through loop (H1), quick link (G), and loop (H2).

8. Attach mounting plate (A) to junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5”). The side of the mounting plate (A) marked with “GND” and two convex points must face out.
   CONNECTING THE WIRES (Fig. 2)

9. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.

10. Tuck wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1)

11. Slide canopy (D) over mounting plate (A) and secure with screws (E).

12. Install (3) three medium base bulbs (J) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification — DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Hardware Bag:

• E. Screw*2
• A. Mounting Plate *1
• D. Canopy *1
• B. Mounting Screw*2
• H. Loop*2
• G. Quick Link*1

Hardware Bag:

• F1. ROD 12″*1
• F2. ROD 12″*2
• F3. ROD 6″*1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>