LeoVince 15400B LV Corsa Slip-On Exhaust Instruction Manual

LeoVince 15400B LV Corsa Slip-On Exhaust

Product Information

The product is a slip-on exhaust system for Kawasaki Z 400/Ninja 400 motorcycles, manufactured by LeoVince. The product is available in three variants – LV Corse Black, LV Corse Carbon, and LV Corse Titanium. The product consists of a muffler, link pipe, and fitting kit. The muffler is available in three finishes – stainless steel black, carbon fiber, and titanium. The product comes with a set of instructions for installation.

Product Usage Instructions

1. Check the list of components supplied with the product against the drawing provided in the manual.
2. Remove the original silencer from the motorcycle.
3. Install the LeoVince slip-on exhaust system by fitting the muffler, link pipe, and fitting kit in place of the original silencer.
4. Secure the components in place using the supplied Allen screws and knurled collar nuts.
5. Replace the muffler repack kit after every 10,000 km of use.
6. Start the engine and wait for a few minutes until it reaches operating temperature. Check for any gas leaks.
7. We recommend that the installation be carried out by a specialist.

ART. 15400B – 15400C – 15400T

• Given name
• Surname
• Address
• Vehicle registration plate
• Tel.
• Date and seller’s stamp

LIST OF COMPONENTS

WEIGHT (Kg)

STOCK                                                 4,11 (Kg)
 | S.s black| Carbon| Titanium
LeoVince| 1,13| 0,99| 1,03

ART. 15400B

• KAWASAKI Z 400 / NINJA 400
• SLIP-ON – LV CORSA – BLACK

ART. 15400B – SPARE PARTS

• KAWASAKI Z 400 / NINJA 400
• A FITTING KIT cod.3015400601R

ART. 15400C

• KAWASAKI Z 400 / NINJA 400
• SLIP-ON – LV CORSA – CARBON

ART. 15400C – SPARE PARTS

• KAWASAKI Z 400 / NINJA 400
• A FITTING KIT cod.3015400601R

ART. 15400T

• KAWASAKI Z 400 / NINJA 400
• SLIP-ON – LV CORSA – TITANIUM

ART. 15400T – SPARE PARTS

• KAWASAKI Z 400 / NINJA 400
• A FITTING KIT cod.3015400601R

FITTING INSTRUCTION

LIST OF SUPPLIED PARTS:
Refer to the list of components and the product drawing included in this booklet.

WARNING:
before carrying out any work on the exhaust, check that its surface has cooled so that it will not damage components, which are not heat-resistant (such as fairing, hoses, rubber sleeves, etc.), or the operator.

INSTALLATION

1. Remove the OE silencer.
2. Check that the mating surfaces are in good clean condition, and slide the link pipe onto the original header, taking care not to damage the graphite bushing (if supplied) which should replace the OE bushing. Partially tighten the securing strap to allow a degree of further adjustment.
3. Slide the Leovince silencer onto the link pipe, check the alignment of the mounting eyes for the springs and the alignment of the exhaust outlet to the rear of the silencer, and then link the parts together with the springs provided
4. Fit the clamps to the silencer. Mount spacers, washers and brackets (if any) as shown on the drawing and then secure by tightening nuts and bolts.
5. Tighten the various clamps which join the Leovince link pipe to the OE exhaust headers.
6. Start the engine, wait a few minutes until it reaches operating temperature, and check that there are no gas leaks.

IMPORTANT:
During the first km of running, the exhaust system needs to break in; therefore, slight gas leakage might occur. After approximately 100 Km, check all the fasteners.

ADJUSTMENT:
This silencer has been developed by Leovince on an electronic dynamometer using a vehicle in perfect condition, and in standard trim

MAINTENANCE

From time to time, check all the brackets and fasteners, which could be affected by use (sound-deadening material, seals and other rubber parts), and replace them periodically. The silencer may be cleaned using gasoline, diesel oil or alcohol. Absolutely avoid the use of any kind of solvent.It is normal for there to be some discoloration of the silencer, which is the result of heat and the nature of the materials used.

IT IS FORBIDDEN to modify silencers. Whatever form this may take, Belgrove Sp. z o.o. declines any responsibility for defects, problems, or malfunction, arising from the use of any product which has been modified or tampered with.

We suggest the fitting to be made by professionals.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>