LeoVince 15252 Stainless Steel Exhaust Instruction Manual
- June 10, 2024
- LeoVince
Table of Contents
ART. 15252 – 15252B
FULL SYSTEM
LV-10 / LV-10 BLACK
HONDA MSX 125 / GROM
TYPE: JC92; 1/1
15252 Stainless Steel Exhaust
ART. 15252-15252B
Given name
Surname
Address
Vehicle registration plate
Tel.
Date and seller’s stamp
LIST OF COMPONENTS
| STAINLESS S.| BLACK
---|---|---
1 – Muffler| cod. 309746481| cod. 309746485
2 – Link pipe| cod. 3015252201| cod. 3015252201
3 – Fitting kit| cod. 3015252601| cod. 3015252601
WEIGHT
STOCK ORIGINAL 3.38 (Kg)
| Stainless steel| S.s. Black| Carbon
LeoVince| 1,83| 1,83| 2.
ART. 15252
HONDA MSX 125 / GROM
FULL SYSTEM – LV-10 – STAINLESS STEEL 
ART. 15252 – SPARE PARTS
HONDA MSX 125 / GROM
A FITTING KIT cod.3015252601R
ART. 15252B
HONDA MSX 125 / GROM
FULL SYSTEM – LV-10 – STAINLESS STEEL BLACK 
ART. 15252B – SPARE PARTS
HONDA MSX 125 / GROM
A FITTING KIT cod.3015252601R
FITTING INSTRUCTIONS
LIST OF SUPPLIED PARTS:
Refer to the list of components and the product drawing included in this
booklet.
WARNING: before carrying out any work on the exhaust, check that its
surface has cooled so that it will not damage components, which are not heat-
resistant (such as fairing, hoses, rubber sleeves, etc.), or the operator.
INSTALLATION:
-
Remove the entire original exhaust system.
Disconnect the Lambda probe from the original exhaust system. (Photo 1) -
Fit the manifold into his seat on the cylinder, fit the flange to the right position, and remembering to fit the sealing gasket when available. Partially tighten the two nuts on the mounting studs to allow a degree of realignment. This is made possible by the clearance between the flange and the mounting studs on the power unit.
-
Slide the Leovince silencer onto the link pipe, check the alignment of the mounting eyes for the springs and the alignment of the exhaust outlet to the rear of the silencer, and then link the parts together with the springs provided.
-
Mount spacers, washers and brackets (if any) as shown on the drawing and then secure by tightening nuts and bolts. (Photos 2-3-4-5)
-
Tighten up all the fasteners, starting with those on the mounting flange at the power unit. Start the engine, wait a few minutes until the correct running temperature has been reached and check there is no gas leakage.
-
If assembly has been correctly undertaken, the overall dimensions of the manifolds should not interfere with the engine parts (radiator, cylinder block, fairings, etc.).
IMPORTANT:
During the first km of running, the exhaust system needs breaking-in;
therefore, slight gas leakage might occur. After approximately 100 Km, check
all the fasteners.
ADJUSTEMENT:
This silencer has been developed by Leovince on an electronic dynamometer
using a vehicle in perfect condition, and in standard trim
MAINTENANCE:
From time to time, check all the brackets and fasteners, which could be
affected by use (sound-deadening material, seals and other rubber parts) and
replace them periodically.
The silencer may be cleaned using gasoline, diesel oil or alcohol. Absolutely
avoid the use of any kind of solvent.It is normal for there to be some
discolouration of the silencer, which is the result of heat and the nature of
the materials used.
IT IS FORBIDDEN to modify silencers. Whatever form this may take, Belgrove Sp.
z o.o. declines any responsibility for defects, problems, or malfunction,
arising from the use of any product which has been modified or tampered with.
We suggest the fitting to be made by professionals
PHOTO 5
Documents / Resources
|
LeoVince 15252 Stainless Steel
Exhaust
[pdf] Instruction Manual
15252 Stainless Steel Exhaust, 15252, Stainless Steel Exhaust, Exhaust
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>