Bailey 145683 Electronic Transformer Light Control Installation Guide
- June 10, 2024
- Bailey
Table of Contents
Bailey 145683 Electronic Transformer Light Control
Product Information
The TOPO Electronic Transformer is designed for use with 12V halogen and LED lamps, with a power range of 0-50W. The transformer has a primary voltage range of 220V-240V and a secondary voltage of 11.5V. It has an output current of 4.3A at full load and an IP20 rating. The transformer is dimmable with most leading/trailing edge dimmers and has a primary input current of 0.23A. The transformer has an output frequency of 30-200cm and an efficiency rating that meets standards EN 61347-1, EN 61347-2-2, EN 62493, EN 55015, EN 61000-3-2, EN 61000-3-3, and EN 61547. It has a power factor, input capacitance, and overload protection with short circuit protection. The transformer has a maximum ambient temperature (ta) and case temperature (tc) for safe usage.
Product Usage
- Before installation, read the specifications to ensure the product is suitable for the operating environment.
- Installation should be done by a qualified professional to avoid any risk of injury or property damage.
- Wet applications require an IP-rated fixture.
- Install the transformer in places with good airflow and away from heat sources.
- The transformer must be installed above the insulation.
- The dimmer should be installed on the power input wire leading to the transformer.
- If flickering or noise occurs, it means the transformer is not compatible with the used LED lamp and/or LED dimmer.
For any additional information or assistance, refer to the installation manual or contact Bailey Electric & Electronics bv.
INSTALLATION MANUAL
Before installation please read the specifications to make sure that this product is suitable for the operating environment.
- This dimmable electronic transformer is compatible with 12V halogen and LED lamps!
- Dimmable with most leading/trailing edge dimmers.
- The transformer must be installed above the insulation.
| Primary voltage range | 220-240V |
|---|---|
| Frequency | 50/60Hz |
| Input current | 0.23A |
| Secondary voltage | 11.5V |
| Output current (full load) | 4.3A |
| Power range | 0-50W (Halogen) 0-30W (LED) |
| Output frequency | 34KHz |
| Efficiency | >95% |
| Power factor | >0.99 |
| Input capacitance | 100nF |
| Ambient temperature (ta) | 50°C |
| Max. case temperature (TC) | 80°C |
| Dimming | R, C & R, L,C |
| Dimensions L x W x H | 109x42x25mm |
| Weight | 80g |
| Primary terminal | 4-pole, screw dia 3.5mm |
| Input wire cross-section | 0.75-2.5mm² |
| Secondary terminal | 2-pole, screw dia 3.5mm |
| Output wire cross-section | 0.75-2.5mm² |
| Secondary cable length (min-max) | 30-200cm |
| Housing material | PC |
| Safety class | II |
| Overload protection | √ |
| Short circuit protection | √ |
Wiring scheme
Standards
- EN 61347-1
- EN 61347-2-2
- EN 62493
- EN 55015
- EN 61000-3-2
- EN 61000-3-3
- EN 61547
Warning – Caution
- Risk of electric shock. Disconnect power before installation, servicing, and removal.
- All safety instructions must be followed to avoid the risk of injury or property damage.
- Wet applications require an IP-rated fixture.
- Installation should be done by a qualified professional.
- Install the transformer in places with good airflow and away from heat sources.
- A dimmer should be installed on the power input wire leading to the transformer.
- If flickering or noise occurs it means the transformer is not compatible with the used LED lamp and/or LED dimmer.
Bailey Electric & Electronics bv
Everdenberg 21 4902TT Oosterhout The Netherlands +31 (0)162 52 2446 |
www.bailey.nl.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>