TYGER TG-NB7T20208 Trax Nerf Bars Installation Guide
- June 1, 2024
- TYGER
Table of Contents
TYGER TG-NB7T20208 Trax Nerf Bars
Product Information
Specifications:
- Brand: TYGER TRAX
- Model: TG-NB7T20208
- Material: Steel
- Compatibility: Universal fit for most vehicles
Product Usage Instructions
Before Installation:
Read instructions carefully before starting installation. Remove contents
from the box and verify all parts are present. Failure to identify damage
before installation could lead to a rejection of any claim. If missing parts
or any damage found, please take a picture for the claim purpose.
Torque Values:
Refer to the following torque values for fastener sizes:
Fastener Size | Class 8.8 Torque (ft-lbs) | Class 10.9 Torque (ft-lbs) |
---|---|---|
6mm | 6-7 | 6-7 |
8mm | 15-16 | 22-23 |
10mm | 31-32 | 44-45 |
12mm | 54-55 | 78-79 |
14mm | 87-88 | 125-126 |
Installation Steps:
-
Step 1:
Starting on the driver/left side of the vehicle, remove the plastic plugs or hex bolts from the factory mounting location along the bottom of the body. -
Step 2:
Select the Driver/Left Front Mounting Bracket (A) and attach it to the front location using the provided hardware. Do not tighten the hardware yet.
Frequently Asked Questions (FAQ):
Q: How do I determine the correct mounting locations for the brackets?
A: Reference the letters printed on the brackets and follow the instructions
provided in the manual to determine the correct mounting positions.
BEFORE INSTALLATION
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT
TORQUE VALUES
Fastener Size | Class 8.8 Torque (ft-lbs) | Class 10.9 Torque (ft-lbs) |
---|---|---|
6mm | 6-7 | 6-7 |
8mm | 15-16 | 22-23 |
10mm | 31-32 | 44-45 |
12mm | 54-55 | 78-79 |
14mm | 87-88 | 125-126 |
PART LIST
- x1 Driver/Left Tyger Trax
- x1 Passenger/Right Tyger Trax
- x1 Driver/Left Front Mounting Bracket (A)
- x1 Passenger/Right Front Mounting Bracket (D)
- x1 Driver/Left Second Mounting Bracket (B)
- x1 Passenger/Right Second Mounting Bracket (E)
- x2 Driver/Left Rear Mounting Brackets (C)
- x2 Passenger/Right Rear Mounting Brackets (F)
- x16 8mm x 30mm Hex Bolts
- x16 8mm x 25mm Combo Bolts
- x16 8mm Lock Washers
- x16 8mm x 24mm OD x 2mm Flat Washers
Reference the letters printed on the brackets to determine mounting locations
Bottom View
ATTENTION : Refer to the D or P labelling on the tubes to determine the Driver or Passenger side steps.
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY. ASSISTANCE IS HIGHLY RECOMMENDED.
-
STEP 1
- Starting on the driver/left side of the vehicle and remove the plastic plugs or hex bolts from the factory mounting location along the bottom of the body (Figs 1 & 2).
Driver/Left Side Installation Pictured
- Starting on the driver/left side of the vehicle and remove the plastic plugs or hex bolts from the factory mounting location along the bottom of the body (Figs 1 & 2).
-
STEP 2
- Select the Driver/Left Front Mounting Bracket (A). Attach the Bracket to the front location with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers (Fig 3). DO NOT tighten hardware
Driver/Left Side Installation Pictured
- Select the Driver/Left Front Mounting Bracket (A). Attach the Bracket to the front location with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers (Fig 3). DO NOT tighten hardware
-
STEP 3
- For the Second (B) and Rear Mounting Brackets (C) refer to (Fig 4) to determine the correct Mounting Bracket.
-
STEP 4
- Repeat STEPS 1 & 2 to attach (1) Driver/Left Second Mounting Bracket (B) to the second location (Fig 5).
Driver/Left Side Installation Pictured
- Repeat STEPS 1 & 2 to attach (1) Driver/Left Second Mounting Bracket (B) to the second location (Fig 5).
-
STEP 5
- Repeat STEPS 1 & 2 to attach (2) Rear Mounting Brackets (C) to the rear locations (Fig 6).
Driver/Left Side Installation Pictured
- Repeat STEPS 1 & 2 to attach (2) Rear Mounting Brackets (C) to the rear locations (Fig 6).
-
STEP 6
- Select the Driver/Left TYGER TRAX. Attach the TYGER TRAX to the Mounting Brackets with (6) 8mm Combo Bolts (Fig 7). DO NOT tighten the hardware.
Driver/Left Side Installation Pictured
- Select the Driver/Left TYGER TRAX. Attach the TYGER TRAX to the Mounting Brackets with (6) 8mm Combo Bolts (Fig 7). DO NOT tighten the hardware.
-
STEP 7
- Level and adjust the TYGER TRAX and tighten all hardware.
-
STEP 8
- Repeat STEPS 1-7 to attach the Passenger/Right TYGER TRAX.
-
STEP 9
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>