Bailey 145378 LED Rope Ribbon Hose Strip Instruction Manual

Table of Contents

Bailey-145378-LED-Rope-Ribbon-Hose-Strip-product

Specifications:

Recommended: Use mounting clips (145378)
Suitable for indoor and outdoor use
Not suitable for use in extreme conditions or locations involving harmful substances
LED light source is not replaceable to preserve water resistance

Power Cord & End Cap Installation:

Before installation, ensure the product specifications match the operating environment.
Use the recommended mounting clips (145378) for installation.

LED Rope Connection:

Ensure the supply voltage matches the rated lamp voltage.
Follow all safety instructions to avoid injury or property damage.
Avoid heavy pressing or overbending during installation; mounting should be firm, not hanging.
Avoid using iron wire or other metallic wire for fastening.
Allow the product to light up for a few minutes to soften during cold weather for easier installation.

Contact Information:

Bailey Electric & Electronics bv Everdenberg 21 4902TT Oosterhout Netherlands
+31 (0)162 52 2446 | www.bailey.nl

Q: Can the LED light source be replaced?

A: No, the LED light source is not replaceable to maintain water resistance.

Before installation please read the specifications to make sure that this product is suitable for the operating environment

$Bailey-145378-LED-Rope-Ribbon-Hose-Strip-fig $1$$

1.5M 230V H05RN-F 2×1.0mm² With built-in AC/DC adaptor Pre-assembled!

Recommended: use mounting clips (145378) $Bailey-145378-LED-Rope-Ribbon- Hose-Strip-fig $2$$

$Bailey-145378-LED-Rope-Ribbon-Hose-Strip-fig $3$$

Maximum length is 100m.
Only cut on the cutting mark (every 100cm), otherwise, it will cause one whole unit to have no light.
PINS (145376): Insert the pins straight into the 2 copper wires of the led rope. Connect with the correct polarity +/- otherwise, it will not light up.
GLUE: The power cord (145375) and end cap (145376) must be filled with standard PVC glue to ensure firm connection and
water tightness. Add glue on led rope: 3-4cm for the power cord, 1-2cm for the end cap. Let it dry for a few seconds.
SHRINK TUBE (145376): push over the connection and heat up.

$Bailey-145378-LED-Rope-Ribbon-Hose- Strip-fig $4$$

$Bailey-145378-LED-Rope-Ribbon-Hose-Strip-fig $5$$

Warning – Caution

Risk of electric shock. Disconnect power before installation, servicing and removal.
Make sure the supply voltage is the same as the rated lamp voltage.
All safety instructions must be followed to avoid the risk of injury or property damage.
Suitable for indoor and outdoor use.
Not suitable for use in extreme conditions or locations involving harmful substances.
Do not heavy press or overbend during installation and mounting should be firm, not hanging.
Do not use iron wire or other metallic wire to fasten.
Light up for a few minutes to soften the body for easy installation during cold weather.
The LED light source is not replaceable to preserve water resistance.

Do not cover the product. Do not attach other items to the product. Store and install the product out of the reach of children. Only use the product when it is working perfectly.
Do not touch the product in the event of a fault or breakdown. Immediately switch off the product and disconnect the power supply.
The following situations are meant by fault or breakdown: there is visible damage to the product, the product is not working perfectly (e.g. it is flickering), there is a burning smell, the results of overheating are visible.
Testing and small repairs must be carried out by a qualified electrician.
In order not to adversely affect the service life, it is advisable to clean the fixture on a regular basis. Only use a soft cloth, water and soap to do so. Avoid exposure to volatile chemical substances such as alcohol, petrol or pesticides.
When your product needs replacing after a long service life, do not dispose of it with your domestic waste. Instead, choose an environmentally friendly method of disposal.
Electrical products may not be disposed of in the same way as normal household waste. Take the fixture to a place where it can be recycled. Consult the local authorities or the seller for advice about collection and processing

The warranty period will begin on the day on which the product was purchased from Bailey and will end after 2 years. If a defect occurs within the warranty period as a consequence of material faults and/or manufacturing errors, Bailey will replace the product. The warranty does not cover consequential damage, nor will any call-out charges, transport costs or installation costs be reimbursed. The warranty does not apply if:
There is no information, or there are no documents, referring to the date of purchase (invoice or delivery note).
The model and/or serial number located on the product is unrecognizable (include a photo of the product sticker or imprint with specifications).
The defect was caused by improper use of the product or use not as intended, or by use in extreme conditions or in conditions involving harmful substances.
The defect was caused by unsuitable connected peripheral equipment or surges in the electricity network.
Damage to the product was caused by external factors.

Bailey Electric & Electronics bv Everdenberg 21 4902TT Oosterhout Netherlands