Bailey PL G23 TC-S LED Lamp Instruction Manual
- October 30, 2023
- Bailey
Table of Contents
Bailey PL G23 TC-S LED Lamp
Product Information
The product is a LED PL G23 TC-S lamp suitable for use in parallel circuits.
It is not suitable for series circuits or use with electronic ballast
(HF/ECG). The lamp should be directly connected to mains voltage (AC) and not
used with emergency units.
It should be used in a fitting with good ventilation, and wet applications
require an IP rated fixture. The LED retrofit installation should be done by a
qualified professional. The lamp is not suitable for use with dimmers or in
extreme conditions or locations involving harmful substances. Due to
overheating, the LED light source may fail rapidly, and it is not suitable for
use in tight luminaires or luminaires where the reflector is close to the
light source.
Specifications
- Product type: LED PL G23 TC-S lamp
- Suitable for: Parallel circuits
- Not suitable for: Series circuits, electronic ballast (HF/ECG), use with emergency units, dimmers, extreme conditions or locations involving harmful substances
- Connection type: Direct connection to mains voltage (AC)
- Other requirements: Good ventilation, IP rated fixture for wet applications, LED retrofit installation by qualified professional
Installation Instructions
- Read the specifications to ensure that the product is suitable for the operating environment.
- Make sure the supply voltage is the same as the rated lamp voltage.
- Follow all safety instructions to avoid a risk of injury or property damage.
- Do not disconnect existing wires from lampholder.
- Rewire according to the diagram provided.
Usage Instructions
- Ensure that the product is suitable for the operating environment before installation.
- Connect the lamp directly to mains voltage (AC).
- Do not use the lamp with electronic ballast (HF/ECG) or in series circuits.
- Disconnect the ballast before use and remove any capacitor if applicable.
- Disconnecting magnetic ballast is optional, not necessary.
- Use the lamp only in parallel circuits.
- The lamp is not suitable for use with emergency units or dimmers.
- Ensure that the lamp is used in a fitting with good ventilation.
- For wet applications, use an IP rated fixture.
- The LED retrofit installation should be done by a qualified professional.
- The lamp is not suitable for use in extreme conditions or locations involving harmful substances.
- Due to overheating, the LED light source may fail rapidly, so it is not suitable for use in tight luminaires or luminaires where the reflector is close to the light source.
LED PL G23 TC-S
AC 220V-240V 50/60Hz, IP20, Temp. -20~35°C
Before installation
please read the specifications to make sure that this product is suitable for the operating environment.
- Connect directly to mains voltage (AC). Not for use with Electronic Ballast (HF/ECG), disconnect ballast before use!
- Disconnecting magnetic ballast is optional, not necessary
INSTALLATION INSTRUCTION
Remove any capacitor (if applicable). Only suitable for parallel circuits. Not suitable for series circuit
EM Ballast / CCG / KVG
Disconnecting magnetic (EM) ballast is optional, not necessary.
AC 220-240V
Rewire according diagram
Warning – Caution
- Risk of electric shock. Disconnect power before installation, servicing and removal.
- Make sure the supply voltage is the same as the rated lamp voltage.
- All safety instruction must be followed to avoid a risk of injury or property damage.
- Do not disconnect existing wires from lampholder.
- Not suitable for use with emergency units.
- Lamp should be used in fitting with good ventilation.
- When used in enclosed fixtures the lumen maintenance and lifetime will be affected.
- Wet applications require an IP rated fixture.
- LED retrofit installation should be done by a qualified professional.
- Not for use with dimmers.
- Not suitable for use in extreme conditions or locations involving harmful substances.
- Due to overheating, the LED light source may fail rapidly. Therefore, not suitable for use in tight luminaires or luminaires where the reflector is close to the light source
Bailey Electric & Electronics bv
Everdenberg 21 4902TT Oosterhout Netherlands
+31 (0)162 52 2446
www.bailey.nl
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>