ASRock iEPF-9000S iEP(F)-9000 Series User Manual

iEPF-9000S iEP(F)-9000 Series

iEPF-9000S iEP(F)-9000 Series
User Manual

Copyright©2022 Airlock Industrial Computer Corp. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent  of ASRock Industrial Computer Corp.
Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without  intent to infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock Industrial Computer Corp.  ASRock Industrial
Computer Corp. assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock Industrial Computer Corp. does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock Industrial Computer Corp., its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data,  interruption of business and the like), even if ASRock Industrial Computer Corp. has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Industrial Website: http://www.asrockind.com

Important Safety Instructions

For user safety, please read and follow all instructions, Warnings, Cautions, and Notes marked in this manual and on the associated device before handling/operating the device, to avoid injury or damage.

1. Read these safety instructions carefully.

2. Retain this user manual for future reference.

3. Read the Specifications section of this manual for detailed information on the recommended operating environment.

4. Disconnect the equipment from all AC outlets before cleaning. Use only a damp cloth
   for cleaning. Do not use liquid or sprayed detergent.

5. Place the equipment on a reliable surface during installation. Dropping or letting the equipment fall may cause damage.

6. Do not leave the equipment in an environment with a storage temperature of below -40 °C (-40 °F) or above 85 °C (185 °F) as this may cause damage. The equipment should be stored in a controlled environment.

7. Ensure that the voltage of the power source is correct before connecting the equipment to a power outlet.

8. Position the power cord away from high-traffic areas. Do not place anything over the power cord.

9. If the equipment is not used for a long time, disconnect the equipment from the power source to avoid damage from transient over-voltage.

10.  All cautions and warnings on the equipment should be noted.

11. To avoid electrical shock and/or damage to the device:
    • Keep the device away from water or liquid sources.
    • Keep the device away from high heat or humidity.
    • Keep device properly ventilated (do not block or cover ventilation openings).
    • Always use designated voltage and power source settings.
    • Always install and operate the device near an easily accessible electrical outlet.
    • Secure the power cord (do not place any object on/over the power cord).
    • Only install/attach and operate the device on stable surfaces and/or designated mountings.
    • The power cord must be connected to a socket or outlet with a ground connection.

12. If one of the following occurs, have the equipment checked by service personnel:
    • The power cord or plug is damaged.
    • Liquid has penetrated into the equipment.
    • The equipment has been exposed to moisture.
    • The equipment is malfunctioning or does not operate according to the user manual.
    • The equipment has been dropped and damaged.
    • The equipment shows obvious signs of breakage.

13. Never attempt to repair the device, which should only be serviced by qualified technical personnel using suitable tools.

14. Any unverified component may cause unexpected damage. To ensure correct installation, always use the components (e.g., screws) provided in the accessory box.

15. This equipment is not suitable for use in locations where children are likely to be present.

16. The equipment should only be installed in a restricted access area.

17. Restricted Access Location: The device must be installed only in a server room or computer room where:
    • Access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken.
    • Access is through the use of a tool or lock and key, or other means of security, and is controlled by the authority responsible for the location.
    • Leave enough clearance (25 inches in the front and 30 inches in the back of the rack) to allow the front door to be opened completely and to allow for sufficient airflow.
    • This product is intended for installation only in a Restricted Access Location.
    • This product is not suitable for use with visual display devices in the workplace according to §2 of “the German Ordinance for Work with Visual Display Units”.

18. The equipment is intended to be supplied by the external power source (UL listed/ IEC 60950-1/ IEC 62368-1 approved) whose output complies with ES1/SELV. To reduce potential safety issues, only the AC adapter provided with the product, a replacement AC adapter provided by ASRock Industrial or an agency, or an AC adapter purchased as an accessory from ASRock Industrial or an agency should be used with the product.

19. This power adapter (FSP330-AAAN3) is intended to be supplied based on a Uncertified and suitable for use at an operating/storage temperature of 0 °C (32 °F)~ 40 °C (104 °F)/ -20 °C (-4 °F)~80 °C (176 °F), and the current output is rated 13.75A. If you need further assistance, contact ASRock Industrial for additional information.

20. The ambient temperature of the iEP-9000E series: 70 °C (158°F) max.; the ambient temperature of the iEPF-9000S series: 75 °C (167°F) max.

21. The terminal block is suitable for V+V-, with 3 units each (16~18AWG), totaling 6 units. The torque value is 0.69Nm. Please ensure the use of copper conductors only. Kindly note that installation must be carried out by a professional.

22. LAN port must use shielded LAN cable.

Replaceable Batteries
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
CAUTION
The equipment is equipped with a battery-powered real-time clock circuit. There is a risk of explosion if a battery is incorrectly replaced. Replace only with the same or equivalent type as designated by the manufacturer. Discard all used  batteries according to the manufacturer’s instructions.
LITHIUM-METAL BATTERY WARNING
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type designated by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
WARNING
All interconnection to the EUT is intended for indoor locations, and as a result, the PoE network interconnected to the EUT is considered ES1/SELV, designed exclusively for connection to the PoE network without routing to the outside plant.
WARNING
Input voltage rated 9~36V, 30~18A.
Packing: The unit should be carried with both hands and handled with care.
Maintenance: Use only approved products or a dry applicator to clean and maintain the surfaces.
The terms HDMI™ and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Contact Information
If you need to contact ASRock Industrial or want to know more about ASRock Industrial, you’re welcome to visit ASRock Industrial’s website at www.asrockind.com; or you may contact your dealer for further information.
ASRock Industrial Incorporation
Email: Info_ipc@asrockind.com

Chapter 1 Introduction

Thank you for purchasing iEPF-9000S-EX4 / iEPF-9002S-EX4 / iEP-9000E / iEP- 9002E, a reliable barebone system produced under ASRock Industrial’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock Industrial’s commitment to quality and endurance.
Because the hardware specifications might be updated, the content of this documentation will be subject to change without notice. In case any modifications of this documentation occur, the updated version will be available on ASRock  Industrial’s website without further notice. If you require technical support related to this product, please visit our website for specific information about the model you are using. ASRock Industrial’s Website: www.ASRockInd.com
The illustrations shown in this manual are examples only. The actual system may differ depending on the product model you purchased.

1.1 Key Features
iEPF-9000S-EX4

• Intel® 10 Gen Xeon® W or Core™ Processors with W480E chipset
• 4 x 260-pin DDR4 SO-DIMM up to 128GB (32GB per DIMM)th
• 1 x PCIe x16 (PCIe Gen3) or 2 x PCIe x8 (PCIe Gen3), 2 x PCIe x4 (PCIe Gen3)
• 1 x M.2 Key M, 1 x M.2 Key B, 1 x M.2 Key E, 2 x Mini PCIe
• 4 x USB 3.2 Gen2x1, 2 x USB 2.0, 6 x COM, 4 x SATA3, 8 x DI, 8 x DO
• 5 x Intel Gigabit LAN (2 support PoE)
• Supports Triple Display, 2 x DisplayPort, 1 x VGA
• Powerful Edge AI acceleration enabled by the most flexible mechanical, thermal, and power design, with support for 275mm x 121mm x 42mm (L x H x D) max. and up to 255W graphics card

iEPF-9002S-EX4

• Intel®10 Gen Core™ Processors with H420E chipset
• 2 x 260-pin DDR4 SO-DIMM up to 64GB (32GB per DIMM)
• 1 x PCIe x16 (PCIe Gen3)
• 1 x M.2 Key M, 1 x M.2 Key B, 1 x M.2 Key E, 2 x Mini PCIe
• 4 x USB 3.2 Gen1x1, 2 x USB 2.0, 6 x COM, 2 x SATA3, 8 x DI, 8 x DO
• 3 x Intel Gigabit LAN th
• Powerful Edge AI acceleration enabled by the most flexible mechanical, thermal, and power design, with support for 275mm x 121mm x 42mm (L x H x D) max. and up to 255W graphics card

iEP-9000E

• Intel® 10 th Gen Xeon® W or Core™ Processors with W480E chipset
• 4 x 260-pin DDR4 SO-DIMM up to 128GB (32GB per DIMM)
• 1 x M.2 Key M, 1 x M.2 Key B, 1 x M.2 Key E, 2 x Mini PCIe
• 4 x USB 3.2 Gen2x1, 2 x USB 2.0, 6 x COM, 4 x SATA3, 8 x DI, 8 x DO
• 5 x Intel Gigabit LAN (2 support PoE)
• Supports Triple Display, 2 x DisplayPort, 1 x VGA

iEP-9002E

• Intel®10 Gen Core™ Processors with H420E chipset
• 2 x 260-pin DDR4 SO-DIMM up to 64GB (32GB per DIMM)
• 1 x M.2 Key M, 1 x M.2 Key B, 1 x M.2 Key E, 2 x Mini PCIe
• 4 x USB 3.2 Gen1x1, 2 x USB 2.0, 6 x COM, 2 x SATA3, 8 x DI, 8 x DO
• 3 x Intel Gigabit LAN th

1.2 Package List

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>