AFX MOTORSPORTS DEF048 High Impact Steel Rear Bumper Instruction Manual
- June 11, 2024
- AFX MOTORSPORTS
Table of Contents
AFX MOTORSPORTS DEF048 High Impact Steel Rear Bumper
Product Information
This product is designed for off-road use only. The product includes the following hardware:
- 1/4 washer (x2)
- 1/4 x 11/2 screw
- U CPLAMP
- 1/4 nuts (x2)
- 1/4 x 1 screw
- Arms bumper
- 1/4 x 2 screw
- 1/4 washer (x2)
- 3/8 x 1 screw with washer and nut
The product should be assembled with the included hardware. The arms bumper should be assembled using the 1/4 x 2 screw and two 1/4 washers. The U CPLAMP should be attached using the 1/4 x 11/2 screw and two 1/4 nuts. The arms bumper can then be attached to the vehicle using the 3/8 x 1 screw with a washer and nut.
HOW TO INSTALL
Pieces included:
Hardware:
- (2x) 3/8 x 1″ Screw with washer and nut.
- (2x) 1/4 x 2″ Screws with nut.
- (2x) 1/4 x 11/2″ Screws with two washers and nuts.
- (2x) 1/4 x 1″ Screws with washer and nut.
Tools needed (Not Included):
- T30 Torx Screwdriver.
- 5/32″ Allen Key.
- 7/16″ or 14 mm Combination Wrench.
- Assemble the arms of the bumper (as it is shown in the image). Use a 1/4 x 2″ screw with a nut, do not tighten it yet
- Align the bumper with the original perforations of the car and use two 3/8 x 1″ with a washer and nut (do not tighten yet).
- Place the “U” CLAMP hardware over the tube (as it is shown in the image). Use a 1/4 x 1″ screw and a 1/4 x 1 h” screw with a double washer and nut (as it is shown in the reference image). Repeat this step on the other side.
- To finish the installation, tighten all the screws.
Liability Statement
AFX Motorsports products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by AFX Motorsports and is not recommended. AFX Motorsports products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact AFX Motorsports to verify that they will work together. Although AFX Motorsports has thousands of satisfied customers, user should be aware that installing bumpers, rock sliders, spare tire carriers, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect user from severe injury or death. AFX Motorsports urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing AFX Motorsports products, user agrees that should damages occur, AFX Motorsports will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. AFX Motorsports, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from AFX Motorsports. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. AFX Motorsports will warranty only parts provided by AFX Motorsports. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by AFX Motorsports. AFX Motorsports parts and products are not warrantied if item was not installed properly, misused, or modified.
- For technical support, please write us to: [email protected] or call us at: Ph. 956-242-6521
- www.afxmotorsports.com
- 4610 Modern Lane, Laredo, TX 78041 Ph. 956-242-6521