AFX MOTORSPORTS DEF012 Steel Rear Bumper Instruction Manual

: June 11, 2024
: AFX MOTORSPORTS

Table of Contents

AFX MOTORSPORTS DEF012 Steel Rear Bumper
Product Information
Product Usage Instructions
Hardware
INSTALLATION
Liability Statement
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AFX MOTORSPORTS DEF012 Steel Rear Bumper

AFX-MOTORSPORTS-DEF012-Rear-Bumper-PRODUCT

Product Information

This is a Steel Rear Bumper for Polaris RZR 900 / 1000XP / 1000XP-4 manufactured by AFX Motorsports. The product comes with assembly instructions, hardware, and U clamps.

The hardware includes

(2x) 3/8 x 1 Screw with washer and nut
(2x) 1/4 x 2 Screws with nut
(2x) 1/4 x 1 1/2 Screws with two washer and nut
(2x) 1/4 x 1 Screws with two washer and nut

The product is designed for off-road use only and can be installed on Polaris RZR models from 2014-2018.

Product Usage Instructions

Assemble the arms of the bumper as shown in the image using a 1/4 x 2 screw with nut. Repeat this step on the other side.
Locate the perforations that are in the low part of the rear suspension plate and align the bumper with the perforations as shown in the image.
Use two 3/8 x 1 screws with washer and nuts to secure the bumper to the perforations on the rear suspension plate.
Use a 1/4 x 1 screw with two washers and nut to install the bumper arms to the U clamp.
Tighten all screws using a 3/4 wrench and a 7/32 Allen key.

Note Before using the product, ensure that it is installed correctly and securely. A combination wrench of 9/16 or 14 mm may also be needed during installation. If you have any questions or concerns about the installation process, please contact AFX Motorsports at info@afxmotorsports.com.

Pieces included

Hardware

(2x) 3/8 x 1” Screw with washer and nut.
(2x) 1/4 x 2” Screws with nut.
(2x) 1/4 x 1 1/2” Screws with two washer and nut.
(2x) 1/4 x 1” Screws with two washer and nut.

Tools needed (Not Included)

3/4” Wrench.
7/32” Allen Key.
9/16” or 14 mm Combination Wrench.

INSTALLATION

Assemble the arms of the bumper (as it is shown in the image). Use a 1/4 x 2” screw with nut, do not tighten yet (repeat this step on the other side).
Locate the perforations that are in the low part of the rear suspension plate. Align the bumper with the perforations (as it is shown in the imgae). Use two 3/8 x 1” screws with a washer and nuts.
Place the “U” CLAMP hardware over the tube (as it is shown in the image). Use a ¼ x 1” screw and a ¼ x 1 ½” screw with double washer and nut (as it is shown in the reference image). Repeat this step on the other side.
To finish the installation, tighten all the screws.

Liability Statement

AFX Motorsports products are designed to best fit the user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by AFX Motorsports and is not recommended. AFX Motorsports products could interfere with other aftermarket accessories. If user has aftermarket products on the machine, contact AFX Motorsports to verify that they will work together. Although AFX Motorsports has thousands of satisfied customers, user should be aware that installing bumpers, rock sliders, spare tire carriers, etc. will change the ride of the machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect user from severe injury or death. AFX Motorsports urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing AFX Motorsports products, the user agrees that should damages occur, AFX Motorsports will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. AFX Motorsports, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from AFX Motorsports. The total liability of the seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. AFX Motorsports will warranty only parts provided by AFX Motorsports. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by AFX Motorsports. AFX Motorsports parts and products are not warrantied if item was not installed properly, misused, or modified.