AFX MOTORSPORTS SKI064-A Aluminium RockSliders CAN AM Maverick 2 Seater Instruction Manual

AFX MOTORSPORTS SKI064-A Aluminium RockSliders CAN AM Maverick 2 Seater

Product Information

• Product Name: Aluminium RockSlides
• Model: Ski064-A
• Compatibility: Can-Am Maverick 2 Seater (2013-2016)
• Thickness: 1/8 – 3/16 inches
• Pieces Included: 3/16 Aluminium RockSlider, Pilot Side
• Hardware Included: (18x) 3/16 x 1/2 Rivets, (18x) 3/16 Flat Washer, (2x) 6mm x 30mm Screws
• Tools Required (Not Included): T-40 Torx Screwdriver, Rivet Tool
• Usage: For Off Road Use Only

Product Usage Instructions

1. Remove the screws from the rear and front parts of the side plastic protectors of your Can-Am Maverick using a T-40 Torx Screwdriver. Keep the screws and remove the side plastic protectors of your vehicle.
2. Set the Aluminium rock slider (Pilot or Co-pilot’s side) in the vehicle, and fasten it using the original screws and holes of the side plastic protectors. It is recommended that you place the bolts on the rear part of the Aluminium rock slider and then the front; Do not tighten them yet. Fasten the rear part first, and secondly, the front part. (Recommended).
3. Using a riveting tool, place the rivets on the bottom part of the RockSlider in the holes provided. Use a washer for each rivet (Included). It is recommended to first place the 2 rivets of the front holes (Fig. 1), and then place 2 rivets on the rear holes (Fig. 2). This will help to have an easier installation on the remaining rivets.
4. Put the last rivets on the remaining holes of the bottom part of the RockSlider.
5. Repeat steps 2-4 for the RockSlider on the other side of the vehicle.
6. Tighten all remaining bolts and enjoy your ride!

Liability Statement:
This product is for off-road use only. AFX Motorsports is not liable for any damages or injuries caused by misuse of this product.

Pieces included

Hardware

• (18x) 3/16” x 1/2” Rivets.
• (18x) 3/16” x 1/2” Rivets.
• (2x) 6mm x 30mm screws.

Tools needed Not Included

• T-40 Torx Screwdriver.
• Rivet Tool.

HOW TO MAKE THE INSTALLATION

1. Remove the screws from the rear and front part of the side plastic protectors of your Can-Am Maverick. For this step, use a T-40 Torx Screwdriver. Keep the screws and remove the side plastic protectors of your vehicle.
2. Set the Aluminium rock slider (Pilot or Co-pilot’s side) in the vehicle, and fasten it using the original screws and holes of the side plastic protectors. It is recommended that you place the bolts on the rear part of the Aluminium rock slider and then the front; Do not tighten them yet.
3. Using a riveting tool, place the rivets on the bottom part of the RockSlider in the holes provided. Use a washer for each rivet (Included). Recommended: First place the 2 rivets of the front holes, (Fig. 1), and then, place 2 rivets on the rear holes (Fig. 2). This will help to have an easier installation on the remaining rivets.
4. Finally, put the last rivets on the remaining holes of the bottom part of the RockSlider.
5. Repeat these steps for the RockSlider on the other side of the Vehicle.
6. Tighten the bolts remaining and enjoy your ride!

Liability Statement

AFX Motorsports products are designed to best fit the user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by AFX Motorsports and is not recommended. AFX Motorsports products could interfere with other aftermarket accessories. If the user has aftermarket products on the machine, contact AFX Motorsports to verify that they will work together. Although AFX Motorsports has thousands of satisfied customers, users should be aware that installing bumpers, rock sliders, spare tire carriers, etc. will change the ride of the machine and may increase maintenance and part wear.

Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect users from severe injury or death. AFX Motorsports urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing AF1 Motorsports products, the user agrees that should damages occur, AFX Motorsports will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges.

AFX Motorsports, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from AFX Motorsports. The total liability of the seller to the user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. AFX Motorsports will warranty only parts provided by AFX Motorsports. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by AFX Motorsports. AFX Motorsports parts and products are not warranted if the item was not installed properly, misused, or modified.

Contact Information

For technical support, please write us to:
info@afxmotorsports.com

Call us at:
Ph. 956-242-6521

www.afxmotorsports.com
4610 Modern Lane, Laredo, TX 78041 Ph. 956-242-6521.

THIS PRODUCT IS FOR OFF-ROAD USE ONLY

Documents / Resources

| AFX MOTORSPORTS SKI064-A Aluminium RockSliders CAN AM Maverick 2 Seater [pdf] Instruction Manual
SKI064-A Aluminium RockSliders CAN AM Maverick 2 Seater, SKI064-A, Aluminium RockSliders CAN AM Maverick 2 Seater, CAN AM Maverick 2 Seater, Maverick 2 Seater, 2 Seater
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>