AFX MOTORSPORTS SKI102-S Aluminum A Arm Guards Instruction Manual
- June 11, 2024
- AFX MOTORSPORTS
Table of Contents
AFX MOTORSPORTS SKI102-S Aluminum A Arm Guards
Product Information
This product is designed for off-road use only and is compatible with the Can- Am Maverick X3, XDS, and XRS models. The SKU for this product is SKI102-S and it can be purchased at AFX Motorsports.
Product Package Contents
- 4x Z Brace Clamps
- 4x 1/4 x 3 Bolts with washers and nuts
- 4x 1/4 x 1 Bolts with washers and nuts
Product Usage Instructions
- Install two 1/4 x 3 bolts with washers and nuts (included) to fasten the front part of the A-Arm Guard. Be sure that the bolt head will be pointing to the ground. Use the original perforations on the front suspension plates of the vehicle (See figure 1).
- Fasten the rear part of the A-Arm Guard to the tubes of the front suspension using the Z brace clamps provided in the package and the perforations provided in the A-Arm Guard. Use a 1/4 x 1 bolt with a washer and nut for each clamp (included). Be sure that the bolt head will be pointing to the ground. (See Figure 1).
- Finally, tighten all the bolts using a 7/32 Allen Key and a 9/16 or 14 mm Combination Wrench.
TIP:
Install the bolts finger-tight at first until all hardware has been installed.
Liability Statement:
This product is for off-road use only. AFX Motorsports is not responsible for
any damage or injury that may result from the installation or use of this
product.
Pieces included
- A-Arm Guard
- (4x) “Z” Brace Clamps.
- (4x) 1/4” x 3” Bolts with washers and nuts.
(4x) 1/4” x 1” Bolts with washers and nuts.
Tools needed Not Included
- 7/32” Allen Key.
- 9/16” or 14 mm Combination Wrench.
TIP:
Install the Bolts Finger tight at first until all hardware has been installed.
Installation
- Install two 1/4” x 3” bolts with washers and nuts (Included) to fasten the front part of the A-Arm Guard. Be sure that the bolt head will be pointing to the ground. Use the original perforations on the front suspension plates of the vehicle (See figure 1).
- Fasten the rear part of the A-Arm Guard to the tubes of the front suspension using the “Z” brace clamps provided in the package and the perforations provided in the A-Arm Guard. Use a 1/4” x 1” bolt with a washer and nut for each clamp (Included). Be sure that the bolt head will be pointing to the ground. (See figure 1).
- Finally, tighten all the bolts.
Liability Statement
AFX Motorsports products are designed to best fit the user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by AFX Motorsports and is not recommended. AFX Motorsports products could interfere with other aftermarket accessories. If the user has aftermarket products on the machine, contact AFX Motorsports to verify that they will work together. Although AFX Motorsports has thousands of satisfied customers, users should be aware that installing bumpers, rock sliders, spare tire carriers, etc. will change the ride of the machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs increases the risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect users from severe injury or death. AFX Motorsports urges operators and occupants to wear a helmet and appropriate riding gear at all times. By purchasing and installing AFX Motorsports products, the user agrees that should damages occur, AFX Motorsports will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges.
AFX Motorsports, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from AFX Motorsports. The total liability of the seller to the user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim. AFX Motorsports will warranty only parts provided by AFX Motorsports. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by AFX Motorsports. AFX Motorsports parts and products are not warranted if the item was not installed properly, misused, or modified.
Contact Information
For technical support, please write us to:
info@afxmotorsports.com
Call us at:
Ph. 956-242-6521
www.afxmotorsports.com
4610 Modern Lane, Laredo, TX 78041 Ph.
956-242-6521.
THIS PRODUCT IS FOR OFF ROAD USE ONLY
Documents / Resources
| AFX
MOTORSPORTS SKI102-S Aluminum A Arm
Guards
[pdf] Instruction Manual
SKI102-S Aluminum A Arm Guards, SKI102-S, Aluminum A Arm Guards, A Arm Guards,
Arm Guards, Guards
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>