AFX MOTORSPORTS TEC007 RZR 900 / 1000 2 Seats Aluminum Roof Instruction Manual
- June 11, 2024
- AFX MOTORSPORTS
Table of Contents
TEC007 RZR 900 / 1000 2 Seats Aluminum Roof
Product Information
The Aluminum Roof Installation Manual is a guide for installing
an aluminum roof on RZR 900/1000 2-seater vehicles. This product is
designed for off-road use only and is available for purchase at AFX
Motorsports. The installation process requires the removal of the
original plastic roof and fastening the aluminum roof to the center
tubular structure of the vehicle using bolts and nuts.
Product Usage Instructions
-
Begin by removing the original plastic roof of the vehicle.
This can be done by removing the screws located on the rear and
front part of the roof. -
Using a 3/4 wrench, remove the 4 nuts that hold the center
tubular structure of the roof. Keep these nuts. -
Place the new aluminum roof on the tubular structure, starting
from the rear to the front, as shown in the image provided in the
manual. -
Install the anti-rattling strip provided with the product.
-
Using the hardware provided with the product, fasten the
aluminum roof to the center tubular structure of the vehicle by
installing four 1/4 x 1 bolts with washers and nuts. -
Use a 3/4 wrench, 5/32 Allen key, and a 7/16 or 14mm
combination wrench to tighten all bolts and nuts. It is recommended
to install the bolts finger tight at first until all hardware has
been installed.
Once all hardware has been installed, ensure that the structure
is placed correctly and fasten it with the four original nuts. The
Aluminum Roof Installation Manual also includes a liability
statement that should be read before installation.
5
ALUMINUM ROOF
INSTALLATION MANUAL
info@afxmotorsports.com THIS PRODUCT IS FOR OFF ROAD USE ONLY
RZR 900 / 1000 2 SEATS
TEC007
FOR PURCHASING AT AFX MOTORSPORTS ALUMINUM ROOF
FOR CAN AM X3 2 SEATER
HOW TO INSTALL
Aluminum Roof.
1 In case of having the OEM Plastic Roof: Uninstall the
original plastic roof of the vehicle, removing the screws located on the rear
and front part of the roof.
2 With an 3/4″ wrench, remove the 4 nuts that holds the
center tubular structure of the roof. Keep the nuts.
3 Place the roof on the tubular structure, as shown on the
image below, by starting from rear to front.
(1x) 1/2″ Anti-rattling Strip.
Hardware:
(4x) 1/4″ x 1″ Bolts with washers and nuts.
3/4″ Wrench. 5/32″ Allen Key. 7/16″ or 14 mm Combination Wrench. TIP: Install
the Bolts Finger tight at first until all hardware has been installed.
Liability Statement
AFX Motorsports products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by AFX Motorsports and is not recommended. AFX
Motorsports products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact AFX Motorsports to verify
that they will work together. Although AFX Motorsports has thousands of
satisfied customers, user should be aware that installing bumpers, rock
sliders, spare tire carriers, etc. will change the ride of machine and may
increase maintenance and part wear. Operating any off-road machine while, or
after, consuming alcohol and/or drugs increases risk of bodily harm or death.
No warranty or representation is made as to this product’s ability to protect
user from severe injury or death. AFX Motorsports urges operators and
occupants to wear a helmet and appropriate riding gear at all times. By
purchasing and installing AFX Motorsports products, user agrees that should
damages occur, AFX Motorsports will not be held responsible for loss of time,
use, labor fees, replacement parts, or freight charges. AFX Motorsports, nor
any 3rd party, will not be held responsible for any direct, indirect,
incidental, special, or consequential damages that result from any product
purchased from AFX Motorsports. The total liability of seller to user for all
damages, losses, and causes of action, if any, shall not exceed the total
purchase price paid for the product that gave rise to the claim. AFX
Motorsports will warranty only parts provided by AFX Motorsports. Any damage
or problems with OEM housings, bearings, seals, or other manufacturers’
products will not be covered by AFX Motorsports. AFX Motorsports parts and
products are not warrantied if item was not installed properly, misused, or
modified.
4 Once the structure is placed, fasten it with the 4 original
nuts and tigthen them. Anti-rattling Strip
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>