HORMANN N500 Up and Over Garage Door Instruction Manual

: June 4, 2024
: HORMANN

Table of Contents

HORMANN N500 Up and Over Garage Door
About these instructions
Safety instructions
Fitting and initial start-up
Dismantling and disposal
TOOLS NEEDED
ASSEMBLY
TOOLS REQUIRED FOR INSTALLATION
INSTALLATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HORMANN N500 Up and Over Garage Door

HORMANN-N500-Up-and-Over-Garage-Door-PRODUCT

Dissemination as well as duplication of this document and the use and communication of its content are prohibited unless explicitly permitted. Noncompliance will result in damage compensation obligations. All rights reserved in the event of patent, utility model or design model registration. Subject to changes.

About these instructions

Make sure that these instructions remain with the door operator!
Read and follow these instructions carefully!They provide you with important information on the safe fitting and operation of the door.
Keep these instructions in a safe place for later reference.
Enter the serial number (see the data label) here.

The following documents for safe handling and maintenance of the door system must be placed at the disposal of the end user:

These instructions
Instructions for up-and-over garage door
Instructions for the operator
The enclosed log book

Safety instructions

ATTENTION:
IMPORTANT SAFETY INSTRUCTIONS.
FOR THE SAFETY OF PERSONS, IT IS IMPORTANT TO COMPLY WITH THE FOLLOWING INSTRUCTIONS. THESE INSTRUCTIONS MUST BE KEPT.
The manufacturer is not liable for damage resul-ting from non-compliance with these instructions including the safety instructions.

Qualified persons
Have a qualified person (competent person in acc. with EN 12635) fit, start-up and maintain the door following these instructions. While doing so, observe the requirements in the standards EN 12604 and EN 12635.

Intended use
Break-in resistance equipment is designed and intended exclusively for the up- and-over garage door and for private use only. If you would like to use the door with break-in resistance equipment in a commercial application, first check whether the currently valid national and international regulations permit such use. Break-in resistance equipment can be used with a manually operated garage door or a garage door equipped with an operator.

General safety instructions

Always keep the door’s area of travel clear. When operating the door, always make sure that there are no persons, especially children, or objects within the door’s area of travel!
Do not alter or remove any components! You could otherwise risk putting important safety components out of action. Only use original parts intended for use with this particular garage door.

RC2
Fitting behind the opening

	N 80	N 500
Clear width	max. 3500 mm	max. 5000 mm
Clear height	max. 2750 mm	max. 2750 mm
Styles	902, 957, 990,

941

| 402, 412, 420
Door with wicket door| Styles 902| –

No RC2
Fitting in the opening, Glazing, N 500 with wicket door

Requirements of the door

HORMANN-N500-Up-and-Over-Garage-Door-FIG-1

Fitting and initial start-up

Safety instructions

WARNING Danger of injury
There is a danger of injury during fitting. Observe the following instructions:

Wear safety glasses and protective gloves.
Secure the door leaf against uncontrolled movements.
When operating the door, make sure that neither persons, children in particular, nor objects are located within the door’s area of travel.

DANGER Electrical connection / mains voltage
Contact with the mains voltage presents the danger of a deadly electric shock. For that reason, observe the following warnings under all circumstances:

Electrical connections may only be made by a qualified electrician.
The on-site electrical installation must conform to the applicable protective regulations (230 / 240 V AC, 50 / 60 Hz).
Disconnect the mains plug before any work on the operator or switch the system off at the mains in case of a permanent installation, and protect against being switched back on without authori-sation according to the safety regulations.

ATTENTION

Damage to the product Observe the following instructions:

Functional testing should always be carried out from inside the garage in order to avoid getting locked out.
For garages without a second entrance, an emer-gency release is necessary.

Care products
Unsuitable care products may cause damage.

Only use specialised care products for the profile cylinder. Do not use oil or graphite.
Lubricate the locking rotary catch with a commer-cially available lubricating oil. Do not use grease.

Follow the instructions of the garage door operator for initial start-up and maintenance of the operator. All dimensions in the illustrated section are in mm. To ensure simple and safe fitting, carefully go through the work steps!

Dismantling and disposal

Have the door dismantled and disposed of by a spe-cialist. Have a specialist dismantle the control in the reverse order of these instructions and dispose of it properly. Electrical and electronic devices, as well as batteries, may not be disposed of in household rubbish, but must be returned to the appropriate recycling facilities.