bonsaii C144-D 24 Sheet Cross Cut Shredder Instruction Manual
- June 9, 2024
- Bonsaii
Table of Contents
bonsaii C144-D 24 Sheet Cross Cut Shredder
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP IT FOR FUTURE REFERENCE.
Thanks for your belief and for choosing
In order to ensure the machine is without any quality issues, We have inspected the machines by 100%. Maybe we have remained some shredded papers in the basket or on the blades during the machine test. If it makes you feel uncomfortable or inconvenienced, Please kindly contact with our customer service ([email protected]), We will provide further and better service for you. Thanks!
IMPORTANT
- Please read all instructions carefully and retain instructions for future reference.
- Read through each step carefully and follow the proper order.
- Please place this machine on a flat and stable surface place, please be careful and don’t tip the machine over.
- In case the machine is broken and cannot be used as normal.
- The device should be set up as close as possible to an easily accessible wall Socket.
- Dangerous, please do not disassemble, modify or repair the machine in any way on your own.
- To avoid electric shock, hurting or accidental injury.
- When you empty the basket, or move the machine, or no need to use the machine for a certain period of time, Please kindly make the machine under OFF status and unplug it.
- To avoid fire accident or electric shocks.
- Please don’t use inflammable liquids, gases, water and cleaner to clean the machine.
- To avoid fire accident or electric shock.
- Please don’t use the machine in a very high temperature, very humidity and very heavy dust environment.
- To avoid fire accident, electric shock or machine malfunction
- Please do not put adhesive tape, carbon paper, fabric, plastic film, etc. into the machine for shredding.
- To avoid damaging the machine
- Please do not damage or process the power cables, or do not place heavy objects on the cables.
- To avoid fire accident or, hurting or electric shock
- If abnormal conditions such as smoke or odor occurred, please disconnect the power and stop using it immediately.
- To avoid fire accident or electric shock
- Please do not use if the shredder or the power cable is damaged or defective
- To avoid fire accident or electric shock
- Do not shred greeting cards with sound chips or batteries.
- To avoid fire accident or electric shock.
- Do not hold CD/DVD with finger through the center ring while feeding into the shredder. Serious injury may occur.
IMPORTANT SAFETY INTRODUCTIONS
BEFORE FIRST USE
- User information/ safety instructions.
- WARNING
- Please kindly let children and pets keep away from the machine.
- There are sharp blades inside the machine so as to avoid injury.
- Please kindly let your hands keep away from the sharp blades and feeding opening of paper shredder.
- There are sharp blades inside the machine so as to avoid injury.
- Please kindly let your hair keeps away from the feeding opening of paper shredder.
- If your hair is accidentally sucked in, Please kindly use the “Reverse function” and get rid of the danger.
- Please kindly let your clothing or some small items keep away from the feeding opening of paper shredder like tie, necklaces, sleeves, jewelry, etc ..
- Please don’t use inflammable liquids, gases water and cleaner to clean the machine.
- To avoid fire accident.
- Please kindly don’t touch the sharp edges to avoid injury . This equipment is not intended for use by children.Avoid touching the media feed opening with the hands,clothing or hair. Unplug this equipment when not in use for an extended period of time, Hazardous moving part is in this equipment, keep body parts away from moving parts.
- It cannot be over 24 sheets in one time for the quantity of shredding.
- One folded sheet of paper equates to 2 sheets of paper. Heavier paper, humidity or other than rated voltage may reduce capacity. 85% Maximum sheets per pass to avoid jams.
KNOW YOUR SHREDDER
- Power switch (“”=on, “O”= OFF)
- Power button (green light under work status)
- Bin full indicator light (green light under basket fulling status)
- Overload &Overheat indicator light
- (Overload in red with flashing,Overheat in red)
- FWD indicator light (FWD indicator light in green when Press FWD button)
- REV indicator light (REV indicator light in green when Press REV button)
- FWD button (green light under work status)
- REV button (green light under work status)
- Feed Opening
- Transparent Window
- Basket
- Basket Handle
- Shredder’s Caster
- Caster Brake
- For safety reasons, the shredder will operate only if the shredder head is in correct position and used with supplied basket.
TECHNICAL SPECIFICATIONS
- Will not shred: large paper clips, Unopened junk mail, window or insulated envelopes, continuous forms, newsprint, bound pages (for example notepads, checkbooks, magazines, etc…), transparencies, laminated documents, cardboard, any items with adhesives, hard materials or plastic (except plastic Credit Cards and CDs).
- Maximum recommended daily usage rates: 130 sheets, 5 credit cards.
OPERATING INSTRUCTIONS
- Plug in and press the power switch “ – “
- Power, FWD and REV buttons in green lights, it means under working status. (feed papers, credit card, clips, staple or CD to shred) Continuous operation around 60 minutes.
- WARNING: Beware of injury caused by CD splashing or incorrect CD shredding. Please wear safety goggles and shred the CD in the correct way.
- When inished shredding, please press ” power button” or “power switch” to “O”.
- Bin full: Bin full indicator light in green status, the shredder stops to work and need to clean the wastepaper.
- Bin full indicator light will be OFF and Power& FWD&REV button will be in green with flashing when the basket is opened.
- After clean the basket and assemble the basket with shredder’s body well, Bin full indicator light will be OFF, Power& FWD&REV button in green, Shredder is under staying working status
- Jam: Press Rev button and take out of the jammed paper.
- Overloading: (Overload&Overheat indicator light in red with flashing status, the excess papers will be disgorged automatically and need to take out of excess papers by hand)
- Overheating: (Overload&Overheat indicator light needs to await cooling down) Cool down for around 40 minutes.
- Jam: Press Rev button and take out of the jammed paper.
PRODUCT MAINTENANCE
- Plug in and press the power switch “ – “.
- When power, FWD and REV button in green lights, feed one shredder lubricant pack to shred.
- Press REV button for 2-3 seconds staying ( don’t pull out the shredder lubricant pack)
- Press FWD button 2-3 seconds staying
- Repeat the operations from “REV” to “FWD” for 3-5times till the shredder lubricant pack is fully shredded.
CAUTION: Only use the professional shredder lubricant pack to maintain the shredder such as Bonsaii shredder Lubricant 24-Pack(LS24)/12-Pack(LS12). (no cleaner, inflammable liquids, gases oil, etc..
TROUBLESHOOTING
Malfunction
| ****
Reason
| ****
Solution
---|---|---
Stop Working
| ****
The power plug doesn’t connect to the power supply.
| ****
Please kindly check whether you use the machine with related supply voltage or Plug in again correctly.
Power supply voltage is too low or no power supply.| Please kindly find a
related supply voltage to use it.
The machine is under overheating protection, because the machine is over the
continues working capacity.| ****
Wail for the machine to cool down naturally.
The Hiickness paper is too thin.
| To make the paper thicker ,You can add more papers orfcld the paper.
The machine is overloading because Hie paper is over machine Max shredding quantities.
| Reduce the paper quantity with an acceptable amount and place the paper into the feeding opening the shredder again.
Damage power cable.
| Please replace the power cable with the same parameters by a professional
person or contact with our customer service.
The basket is full.| Empty the basket.
Defective __ machine.
| Please kindly contact with our customer service.
Jam
| ****
Paper jam.
| Please kindly use the function “Reverse” to take out the excess paper.
Keep Running
| ****
Paper dust and other foreign objects cover the sensor.
The location of sensor is in the shredder’s feeding opening look like glass beads or marbles.
|
- Please unplug first and use soft don’t or cotton swabs to clean the foreign objects without any cleaner or water.
- If there are some paper scraps around the sensor area , please kindly use cotton swabs or needle nosed pliers to take out the paper scraps.
CAUTION: please don’t overexert and use Sharp tools to the dean or poke the sensor to avoid damaging the sensor.
Loud Noise| The shredder is placed on an unsuitable place.| ****
Change the location.
If the above answers can not solve your problems, please kindly contact with our customer service team via email [email protected]
LIMITED WARRANTY
We stand by our product and offer a 30-day money-back guarantee. During this time, you could return the item without paying any extra fee if there is a manufacturing defect in it. Please rest assured that the returns are free and easy if there is a manufacturing defect. Otherwise, it would be the customer’s responsibility to cover the shipping fee. Products on sale are also returnable. If the product isn’t meeting your expectations, please email within 30-days of receipt. We will help you to either return or exchange your product. Your original form of payment will be refunded in full once the full return is complete. After 30 days orders may be subject to a 20% restocking fee and all shipping and handling charges will be the responsibility of the customer. Additional return details are listed below. After 60 days the purchase from Bonsaii is non-refundable. If you receive a damaged product, you must notify Bonsaii within 48 hours of delivery. Bonsaii will investigate the claim and notify the freight company about the damage. Please retain all packaging in the event that Bonsaii or the freight company needs to inspect it. These investigations may take several days but merchandise replacements will be processed as soon as possible.
For the product that arrived defective or damage, We’re sorry to hear that your Bonsaii product arrived in less-than-perfect condition. We’d like to resolve this issue right away with the help of our Customer Support Team and Quality Assurance team. They’ll need to know a bit of information on your order as well as the issue you’re experiencing with your Bonsaii product. To report your issue, please reach out to our Customer Support team by emailing [email protected] with your order number. We may need you to make a short video, or take some pictures of the defects of the product and send them to [email protected]. After a preliminary analysis on the video or pictures, we will send you a brand new replacement right away if it is confirmed to be defective on its arrival. If we determine that you have misrepresented the Bonsaii product’s condition and that the product is not defective, we will send you the right instructions and help you to use the product correctly.
If you have any questions or any confusion, Please kindly contact with us: [email protected].
CONTACT
- Manufacture: Bonsen Electronics Limited
- ADDRESS: No.11-12, Lun Pin Chong Industrial Zone San Tun Community, Hou Jie Town 523941 Dongguan City, Guangdong PEOPLE’S REPUBLIC OF CHINA
- 1-844-728-6917
- [email protected]
Made in China