MOES BHT-006 Series Smart Heating Thermostat User Manual

BHT-006 Series Smart Heating Thermostat

BHT-006 Series Thermostat

WIFI Type

For Water Heating/Boiler/Electric Heating

Thank you for purchasing our products, please read
the following terms before installation and use:

Please confirm that this product is suitable for your heating
equipment before installation;
Before installation or maintenance, please make sure to keep
the power off;
Please strictly follow the wiring diagram for wiring installation;
Installation to the wall, please confirm that the fasteners are
suitable for this product;
Do not pull the cable too hard, otherwise the product will be
damaged;
If a hard plastic wire is used in the installation process, it must
be bent to an appropriate angle in advance;
Please arrange for professionals to install;
*Please contact the after-sales service for equipment failure,
please do not try to repair it yourself;

• After installation, please refer to this manual to check again to
  ensure normal and safe use, and keep this manual properly.

ABOUT YOUR THERMOSTATS

The BHT- 006 range has been developed to control electric
underfloor, water heating or water/ gas boiler systems. These units
are designed for use in commercial, industrial, civil and domestic
properties

MODEL DEFINITION

GA: Water heating, 5A
GB: Electric floor Heating, 16A
GC: Water/Gas Boiler, 5A
L: Backlight
N: Modbus Communication
W: Wifi
S2: Both internal sensor and floor external sensor

For example: BHT-006GA

In the box you will find

Thermostat 1pc Screws 2pc
User Guide 1pc Wall plate 1pc
QC Passed 1pc

(Floor sensor is Optional)

TECHNICAL DATA

Power Supply:95 ~240 VAC, 50~60Hz
Current Load: 3A (water heating, gas boiler), 16A (electric heating)
Sensor: NTC3950, 10K
Accuracy: ±1°C
Set Temp. Range: 5-35°C
Room Temp. Range: 5-99°C
Display Temp. Range: 5 ~ 99
Ambient Temp.: 0~ 45°C
Ambient Humidity: 5 ~ 95 % RH (Non Condensing)
Storage Temp.:-10~ 45°C
Power Consumption: <1. 5W
Timing Error: < 1%
Shell Material: PC +ABS ( Fireproof)
Installation Box: 86 * 86mm Square or European 60mm Round Box
Wire Terminals: Wire 2 x 1.5 mm2 or 1 x 2.5 mm2
Protection Class: IP20
Buttons: Capacitive Touch Buttons

FEATURES

On Appearance
1. LCD display, more friendly interface;
2. Touch operation buttons, smoother interaction;
3. The ultra-thin embedded panel perfectly fits all kinds of walls;
4. The borderless small rounded corner design is simple and atmospheric;
5. Compatible with standard 86mm square cassettes and 60mm European
cassettes to meet all installation environments;

On Functionality

1. Rich function options, Modbus, WIFI, keycard, etc., to meet all your needs;
2. Strict temperature control accuracy (±1℃) to provide the warmth you want;
3. Power off protection, save all your settings safely;
4. Provide weather information and humidity display
5. Preset adjustment of 5+1+1 mode in a week, programmable setting of 6 time periods a day, green energy saving, Less cost, more intelligent and environmental protection;
6. Support the creation of product local groups/shares to achieve unlimited centralized control of the number of products/ multi-terminal control;
7. Perfect access: Tmall Genie, Amazon echo, Google Home, full experience new voice control method;

DIMENSION:(mm)

BEFORE WIRING AND INSTALLING

1. Read these instructions carefully. Failure to follow them could damage the
   product or cause a hazardous condition.

2. Check the ratings given in the instructions and on the product to make
   sure the product is suitable for your application.

3. Installer must be a trained, experienced service technician.

4. After installation is complete, check out product operation as provided in
   these instructions.

CAUTION
Electrical Shock or Equipment Damage Hazard. Can shock
individuals or short equipment circuitry.
Disconnect power supply before installation.

INSTALLATION

Your thermostat is suitable for installation within a standard 86mm
pattress box or European 60mm pattress box.
Step 1. Keep power off. See Fig 1.
Step 2. Remove the mounting Plate by rotating the LCD part. See Fig 2.

Step 3. Connect power supply, load into the appropriate terminals.
(see “Wiring your thermostat” for details and Fig 3).
Step 4. Fix the mounting plate into the wall with screws in
the box. See Fig 4.

Step 5. Fasten body of thermostat and the mounting plate through
rotating. See Fig 5.

Step 6. Installation complete. See Fig 6.

HOME SCREEN QUICK REFERENCE

Note: The weather and humidity will be synchronized within 1 hour after the
device is connected to the Internet for the first time, and the weather
will be synchronized every hour thereafter.
Press the / in the power-on state to display the humidity and set temperature

OPERATION

During Power On

1. Power On/off: Press to turn the thermostat on/off.
2. Function & Programmable
Touch to change between manual mode and programme mode.
In manual mode, will show on the display,
In programmable mode, will show on the display.

3. Setting Temperature
In the programming mode, the temperature setting and time setting will be
locked. If the user wants to adjust, he must first adjust the thermostat to
manual mode by pressing the key.
In the mode of manual, press to set the desired temperature.

4. Adjusting/Setting the Clock
Press to set minute, hour and weekday. By using the .
Press once more to confirm and exit.

5. Locking your Thermostat
Press and hold the for 5 seconds to lock/unlock your thermostat
In item 3 of high senior options, you can select full lock or half lock.

6. Adjusting/setting the Program Schedules
When Wi-Fi connection is made, your thermostat will automatically
accept the program schedule made via the APP on your device.
If the schedule is set through the APP, after the APP completes the
schedule setting, the thermostat needs to be turned off once.

If the thermostat does not establish a Wi-Fi connection, manually set the
schedule see below for detailed instructions: To set the program
schedules through your thermostat (NOT via your smartphone/tablet)
simply follow the instructions as below:
Please note: Setting the programme schedule through your
there most at can only be carried out if there is no WiFi
connection between your thermostat and smartphone/tablet.

Press icon four times in a row. You can see “MON TUE WED YHU
FRI” and , and the minutes of time are flashing.
Use to set the minutes;
Press the icon again, the hour of the time will flash, set the
hour by ;
Press the icon again, the temperature setting will flash, set the
temperature by ;
This completes the setting of periods1.
In the same way, complete the settings of periods2, 3, 4 and 5
(display periods1,2), 5 (display periods3, 4).
Press the icon once more to enter the Saturday schedule
settings (you will see the SAT in the upper left corner of the screen).
Repeat the above process to set the period and temp. and Sunday
schedule.
Press the icon once more to confirm and exit.

Default settings for program schedule

Time display

|

WEEKDAY (MONDAY一FRIDAY) (1 2 3 4 5 shows on screen)

|

WEEKEND (SATURDAY)

(6 shows on screen)

|

WEEKEND (SUNDAY)

(7 shows on screen)

---|---|---|---

TIME

|

TEMPERATURE

|

TIME

|

TEMPERATURE

|

TIME

|

TEMPERATURE

Period 1

|

06:00

|

20 C。

|

06:00

|

20 C。

|

06:00

|

20 C。

Period 2

|

08:00

|

15 C。

|

08:00

|

20 C。。

|

08:00

|

20 C。

Period 3

|

11:30

|

15 C。

|

11:30

|

20 C

|

11:30

|

20 C。

Period 4

|

13:30

|

15 C。

|

13:30

|

20 C。

|

13:30

|

20 C。

Period 5(1+2)

|

17:00

|

22 C。

|

17:00

|

20 C。

|

17:00

|

20 C。

Period 6(3+4)

|

22:00

|

15 C。

|

22:00

|

15 C。

|

22:00

|

15 C。

A separate schedule may be set for weekdays (Mon – Fri) and
for weekends (Sat or Sun).

7. Checking the Temperature of Floor Sensor
Press and hold the arrow for 5 seconds to display the temp. of
floor sensor.If there is no external external sensor, “err” will be displayed.

8.Return To Factory Default
Press the Reatore Manufacturer Defaults, you can reset
thermostat.Steps:Open your app -go into your room – click menu on
the top rght corner – move to the end – Press Restore Manufacturer
Defaults.

9.Setting the Functions and Options
During Power Off, press and hold and for 8 sec. in the
order to reach system function. Then press to scroll through
the available functions , and use the arrows to change the
available options. All settings are confirmed automatically.

Code

|

Function

|

Setting and options

|

Default

---|---|---|---

1

|

Temperature

compensation

|

-9 to 9 ℃ (for internal sensor)

|

-3

2

|

Deadzone

Temperature.

|

1-5℃

|

1

3

|

Button Locking

|

00:All buttons are locked except power button. 01:All buttons are locked.

|

01

4

|

Sensor typer

|

In:Internal Sensor(to control the temp.)

Ou:External Sensor(to control the temp.)

AL:Internal/External Sensor (Internal sensor to  control the temp., external sensor to limit the temp.)

|

AL

5

|

Min.Set Temp.

|

5-15℃

|

05

6

|

Max.Set Temp.

|

15-45℃

|

35

7

|

Display Mode

|

00 : Display both set temp. and room temp. 01 : Display set temp. only

|

00

8

|

Low temperature

protection setting.

|

0-10℃

|

00

9

|

High temperature  protection setting.

|

25-70℃

|

45

A

|

Economy Mode

|

00: Non-energy saving Mode

01: Energy saving mode

|

0

B

|

Economy Temp.

|

0-30℃

|

20

C

|

Daytime display

brightness(6:00-22:00)

|

0-8

|

When set to 0, the device will run  for 10 seconds after inactivity.  The screen will go completely  off with no display.

|

1

D

|

Brightness at night (22:00-6:00)

|

0-8

|

1

E

|

Reset

|

00: No factory reset; 01: Factory reset

|

00

F

|

Version number

|

|

U2

ABOUT WIFI

WI-FI CONNECTION

Before using your Wi-Fi thermostat for the first time,you must
configure the Wi-Fi signal and settings through your smartphone
or tablet ,This will allow communication between your
connecteddevices

Step 1 Downlosd your APP

（Fig1-1）

Search for “Smartlife” in Apple Store or Google Play or use a
browser to scan the QR code above (Figure 1-2), and complete
account registration and installation according to the guidance
of the APP.

Step 2. Connect the thermostat Check the tutorial below to

Method 1: Scan the QR code to configure the network guide
(Fig 2.1-Fig 2.3)

Method 2: Ordinary distribution
network guidance
(Fig. 2. 1&Fig. 2.3.1)

Network distribution mode:
1、 EZ Mode
When the thermostat is off, press
and hold the ” “until the
thermostat screen flashes quickly
and displays the ” ” icon,
and then operate according to the
following figure (Fig 2.4-Fig 2.7).

Fig 2.4

2、AP Mode
When the thermostat is off, press and hold the ” ” until the
thermostat screen flashes slowly and the ” ” icon is displayed
(if the ” ” icon appears, continue to press the ” ” until the
thermostat screen Flashes slowly and displays the “ ” icon),
and then operate according to the following figure (Fig 2.8-Fig 2.14).

After connecting to this hotspot,
return to the “smartlife” APP

APP operation interface description

(heating thermostat)）

More settings

SIMPLE EXCEPTION HANDLING

No. | Phenomenon’s | Handling

1. Power is on but without display.

• Check if the terminals between LCD panel and Power Unit Box is loosen.

2. Without output but display works.

• Use new LC panel or new Power Unit Box to replace the old one.

3. Room Temp. Is a little different from the actual.

• Do temperature calibration in item 1 of high senior options

SERVICE

Your thermostat carries an 24 months warranty
from date of purchase. Service out with the warranty
period may incur a charge. More detail please contact
with us directly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>