bonsaii C169-B Paper Shredder Instruction Manual
- June 5, 2024
- Bonsaii
Table of Contents
C169-B Paper Shredder
Instruction Manual
C169-B Paper Shredder Ins
14 Sheets Cross Cut
Customer Service: customer-care@bonsaii.com 1-844-728-6917
Dear customer, Thank you for buying this quality product. Please read
this instruction carefully before initial operation. Particularly take note of
the following safety instructions. Please keep this instruction for future
reference and pass it, when handing over this item.
Cautions:
- Keep all loose articles of clothing, ties jewelry , hair or other small items away from the feed opening to prevent injury.
- Keep in the OFF position when the shredder is not in use for prolonged periods of time.
- Do not place hands , or fingers into the shredder’s throat as serious injury could result.
- Always turn off or unplug the shredder prior to moving, cleaning or emptying the wastebasket.
- Empty wastebasket frequently.
- The document shredder must always be deactivated and disconnected from the electrical line prior to moving, transporting, and cleaning the device and prior to emptying the wastebasket.
- Please do not leave the document shredder unattended. E.g. in the event children and pets are nearby.
- This machine is able to shred paper, clips, staples, and credit cards.
- The device may not be operated with a damaged power cord.
- For indoor use only.
- This machine is no toy. Keep it away from children and pets.
- Please do not spray any flammable gas or oil onto this shredder, it may cause fire.
- Please read the manual before operating the machine
- Sharp edges. Do not touch .
- This equipment is not intended for use by children. Avoid touching the media feed opening with your hands. clothing or hair. Unplug this equipment when not in use for an extended period of time
- Shred width of 13/64X1-37/64 inches
- 14-sheet capacity
Parts and Functions
A: Feed Slot: Paper, clips, staples and Credit Cards
B: Switch-AUTO / OFF / REV
C: LED indicator lamps -Overheat/ Overload / Power
Installation
Unpack and set the machine upright. Put the machine on a horizontal surface. Plug in the machine. The socket outlet should be installed near the equipment and shall be easily accessible
Operating the shredder
Please check the voltage of your shredders carefully before using them.
On the top of the shredder, there are three (3) settings – AUTO, OFF, and REV.
- When AUTO is selected, the shredding process is started automatically by inserting the paper into the feed opening. The shredder will stop automatically when the paper has completed its travel through the feed opening.
- REV is used to assist in the removal of a paper jam, which reverses the shredder process prior to a completed cycle, thus clearing the cutters. If you want to stop shredding the paper, please set it to reverse. The machine will reverse automatically and turn back the papers.
- OFF is used to terminate the power to the shredder. This mode is recommended when emptying the wastebasket or when the shredder is not in use for a prolonged period of time.
Shredder capacity
C169-8 will shred fourteen(14) sheets of A4 size 75g/m2 paper at once and will
accept paper widths up to 8.66 inches. When shredding small materials like
envelopes or receipts, insert them through the middle of the feed opening.
Overheat Protection
C169-8 is equipped with a motor to overheat protection technology. After
continuous work of a period of time, the ‘Overheat’ LED indicator lights up.
Please remember to stop the machine from working after the ‘Overheat’ LED
indicator lights up. Please wait and allow the machine to cool down and
restart when the ‘Overheat’ LED indicator turns off.
Overload Protection
C169-6 is equipped with overload protection technology. The maximum shredding
capacity of this machine at one time is fourteen (14) sheets of A4 size 75g/m2
paper. Exceeding the shredding capacity e.g. inserting more than fourteen (14)
sheets at one pass, or if the paper is not fed squarely into the feed opening,
the ‘Overload’ LED indicator lights up and the machine starts to reverse
automatically. Pull the remaining paper out of the cutters, reduce the number
of sheets and place the paper back into the feed a lot.
Cutter Oiling Instructions
To ensure proper operation and function, periodic oiling of the cutting system
is required Failure to oil your cutting system could result in reduced sheet
capacity performance, excess noise, paper jams, and possibly machine failure.
Oil your cutters every 5th or 6th time you empty the basket, if excess
squeaking and rubbing noise is coming from the machine or if the shredders
sheet capacity has diminished. Squeeze the lubricant across the full width of
the cutters. Push the switch to the ‘AUTO’ position, and then insert paper to
activate the cutting system forward for 3 seconds. Then push the switch to the
‘REV’ position to make the shredder reverse for 3 seconds. Alternate between
AUTO and REV at least three times or until all paper clears the cutters.
Notice
Never use flammable synthetic oil, or petroleum-based or aerosol lubricants
to oil your cutting system. It is recommended to use Bonsaii Shredder
Lubricant Oil or Sheet for oiling the shredder.
BASIC EXPLOITATION RULES
It is not advised to cut as many sheets as indicated as the maximum capacity
of the shredder. By exploiting the machine at its top capacity we
significantly reduce its vitality. Therefore, to maintain a durable and
faultless work of the shredder, it is advised to place no more than 70% of the
maximum amount of sheets to be shredded at one time indicated for each model
by the producer. The maximum amount of sheets should be used only
occasionally. It is forbidden to shred more sheets than the maximum amount of
sheets to be shredded at one time indicated by the producer. It may cause the
blockage of the machine and massive engine overloading, which will diminish
the shredder’s durability or even damage it. Also, you should not shred soft
objects such as foil, paper towels, toilet paper or fabrics. Nor paper with
self-adhesive tape should be placed into the shredder. Those materials wrap
around and jam the knives.
Specification
Shred type:…………Cross cut
Shredding size:…………………..13/64 x 1-37/64 inches
Noise Level:……………..58dB
Shred capacity:……………….14 sheets 75g/m2
Feed Opening:………………8.66 inches
Input: Shredding speed:………………120V- 60Hz 2A 1.8m/min
Basket capacity:……………………………4.8 Gallons
Warranty
The warranty for this appliance is for 12 months from the date of purchase
from an authorized dealer. The appliance has been manufactured with care and
meticulously examined before delivery. Please retain your receipt as proof of
purchase. In the case of a warranty claim, please make contact with our
Customer Service
Notice
The warranty covers only claims for material and manufacturing defects, but
not for transport damage, wearing parts or for damage to fragile components,
e.g. buttons or batteries. This product is for domestic use only and is not
intended for commercial use. The warranty is void in the case of abusive and
improper handling, use of force and internal tampering not carried out by our
authorized service branch. Your statutory rights are not restricted in any way
by this warranty. The warranty period is not extended by repairs made under
the warranty. This applies also to replaced and repaired parts.
Trouble Shooting
| Malfunction | Reason | Solution |
|---|---|---|
| Stop Working | The power plug doesn’t be connected or doesn’t be connected | |
| well. | Please kindly check if you use the shredder with related voltage. If |
yes, Please kindly plug in again.
The voltage is too low or not available.| Please kindly unplug the shredder
and ref and related voltage to use the shredder.
The paper doesn’t be put in the position of the shredder feed opening.| Please
kindly refeed the paper into the shredder feed opening.
The shredder is under protected status for overheating.| Wait for the shredder
to cool down.
The shredder is overloading.| Please kindly take out excess paper and put the
paper into the shredder feed opening again.
The thickness of the paper is too thin or too transparent.| Add opaque paper
or fold the transparent paper multiple.
The basket doesn’t be assembled well.| Please kindly assembled the shredder
again.
Defective power line| Please kindly contact our customer service to replace
the new one for you.
The basket of shredders is full| Please kindly empty the basket in time.
Jam| Paper jam| Using the function of “Reverse° to pull out the jammed paper.
Keep Running| Paper dust and other foreign objects cover the sensor.| Please
kindly unplug the shredder and clean the dust or foreign objects.
Loud Noise| The shredder is placed on an unsuitable place.| Change location
If the above operation can not solve your problem, please contact our customer service team via email at customer-care@bonsaii.com.
Register your product at www.bonsaiishop.com to
get more perks!
Follow us@bonsaiioffice
Bonsen Electronics Inc.
: 4198 Industry Way, Flowery Branch, GA, 30542, USA
:1-844-728-6917
: customer-care@bonsaii.com
Made in Vietnam
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>