Bonsaii C237-B 6 Sheet Cross Cut Paper Shredder Instruction Manual
- June 1, 2024
- Bonsaii
Table of Contents
Bonsaii C237-B 6 Sheet Cross Cut Paper Shredder
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ
AND KEEP IT FOR FUTURE REFERENCE.
Please give us a chance to make it right and do better! Contact our friendly
customer service department for help first. Replacements for missing or
damaged parts will be shipped.
Customer Service:
Email: customer-care@bonsaii.com
Tel: 1-844-728-6917
TIPS:
Thank you for choosing our product!
To ensure that the machines are free of quality issues, we conduct 100%
inspections. However, some shred papers may remain in the basket or on the
blades during machine testing. If this causes any discomfort or inconvenience,
please contact our customer service and we will provide better service for
you. Thank you!
IMPORTANT!
- Please read and keep the manual for future reference.
- Carefully read each step and follow the correct sequence of operation.
- Please place the equipment on a flat and stable surface to prevent tipping over, as this may cause the machine to crack or become unusable.
- The device should be placed as close as possible to an accessible wall outlet.
- Do not disassemble, modify or repair the device on your own to avoid electric shock, injury or damage to the machine.
- When you empty the basket, move the device, or do not need to use the device for a period of time, make sure the device is turned off and unplug the power plug to prevent fire or electric shock.
- Do not use flammable liquids, gases, water or cleaners to clean the device to avoid fire or electric shock.
- Do not use the device in a high temperature, high humidity, or heavily dusty environment to prevent fire, electric shock, or machine malfunction.
- Do not put tape, carbon copy paper, fabric, plastic film, etc. into the device for shredding to avoid damage to the machine.
- Do not damage or process the power cord, and do not place heavy objects on the cable to avoid fire, injury or electric shock.
- lf smoke or odor occurs during use, immediately turn off the power and stop using it to prevent fire or electric shock.
- Do not use the shredder or power cord if it is damaged or defective to avoid fire or electric shock.
- Do not shred greeting cards with sound chips or batteries to avoid fire or electric shock.
IMPORTANT SAFETY INTRODUCTIONS BEFORE FIRST USE
- User information/ safety instructions.
- WARNING
- Please do not allow children to use the machine.
- There are sharp blades inside the machine so as to avoid injury. Please be sure to exercise caution when using it.
- Please do not put your hand close to the shredder blades and the paper feed opening.
- There are sharp blades inside the machine so as to avoid injury. Please be sure to exercise caution when using it.
- Please do not let hair near the shredder’s feed opening.
- If your hair is accidentally sucked in, please use the “reverse function” to remove the danger.
- Please keep your clothing or some small items away from the feed opening of the paper shredder, such as ties, necklaces, sleeves, jewelry, etc.
- Please don’t use inflammable liquids, gases water and cleaner to clean the machine.
- To avoid fire accident.
- Please kindly don’t touch the sharp edges to avoid injury .
- This equipment is not intended for use by children. Avoid touching the media feed opening with the hands, clothing or hair. Unplug this equipment when not in use for an extended period of time, Hazardous moving part is in this equipment, keep body parts away from moving parts.
- It cannot be over 6 sheets in one time for the quantity of shredding.
- One folded sheet of paper equates to 2 sheets of paper. Heavier paper, humidity or other than rated voltage may reduce capacity. 85% Maximum sheets per pass to avoid jams.
KNOW YOUR SHREDDER
- Control panel (Control shredder’s four status “REV”, “OFF”, “FWD”, “AUTO”)
- Reverse Position (“Release the paper”)
- Auto Position (Turn on )
- Forward (compulsorily work)
- OFF (Turn off)
- Power light (work status in green)
- Indicator light (Overheating in red)
- Paper feed opening
- Basket
- Shredder’s handle
- Transparent Window
For safety reasons, shredder will operate only if the shredder head is in correct position and used with supplied basket.
TECHNICAL SPECIFICATIONS
*ONE FOLDED SHEET OF PAPER EQUATES TO 2 SHEETS OF PAPER
Heavier paper, humidity or other than rated voltage may reduce shredding
capacity.
WARNING!
Bin Full:
The wastebasket will become full around 15- 16 shredding passes (6 sheets per
pass) of use Empty the wastebasket when you see shredded materials fill the
window to prevent paper jams.
Never let the wastebasket become full . This will lead to shredded materials
being pulled back up into the shredder and cause jams .
No Trash bag:
If using a plastic bag to line the wastebasket please remove it . This may
cause the shredder not to operate properly
Do not shred:
OPERATING INSTRUCTIONS
-
Plug in and move “control panel” from OFF to AUTO position, “Power Light” in green. (feed papers , clips , staple or credit card to feed opening ).
Continuous operation around 3 minutes. -
When finished shredding or no need to use it, please set to OFF. ****
Jam: Please move “control panel” from “Auto” to “REV” position and pull
out the jammed paper. * Move “control panel” from “REV” to FWD position for
3-5 seconds staying (repeat the operation around 2-3 times if get a very
serious jam) Overheat (power light is in green and indicator light in red,
need to wait for cooling down). Cool down around 40 minutes
Max.6 sheets: If it is over the capacities ,please take out the excess
papers
PRODUCT MAINTENANCE
Plug in and move “control panel” from OFF to AUTO position, “Power Light”
shows green light. (Feed one shredder Lubricant pack to shred ) Move “control
panel” from Auto to “REV” position for 2-3
Move “control panel” from Auto to “REV” position for 2-3 seconds staying and
don’t pull out the shredder lubricant pack. Move “control panel” from REV to
AUTO position to shred the shredder lubricant pack for 3-5 seconds staying and
repeat the operation for 2-3 times till the shredder lubricant pack is fully
shredded. When finished shredding or no need to use it , please set to OFF.
CAUTION
Only use the professional shredder Lubricant pack to maintain the shredder
such as Bonsaii shredder Lubricant 24-Pack ( LS24 )/12-Pack ( LS12).(no
cleaner ,inflammable liquids ,gases oil etc
TROUBLESHOOTING
| Malfunction | Reason | Solution |
|---|---|---|
| **** Won’t shred MAX sheets | **** Paper jam. |
- Lift up the shredder and check whether the outlet is blocked by paper. If there is a lot of paper attached to the outlet, please disconnect the power supply, manually remove the paper at the outlet, and then place the shredder on the basket correctly. Move “control panel” from “REV” to FWD position for 3-5 seconds staying (repeat the operation around 2-3 times if get a very serious jam)
- Switch the shredder to Reverse (REV) mode. While in Reverse, the shredder will back up and loosen the jammed paper. If required, you may need to tug and remove several sheets to effectively clear the machine. When jammed paper is loosened or removed, switch back to the Auto-On mode to continue shredding. Repeat steps if needed.
- With stubborn situations where the reverse function does not help, you may need to clean the jammed paper with shredder oil (cooking oil is acceptable, but don’t use aerosol). Start by drizzling oil into the feed slot where the paper is jammed. Let it soak for about 30 minutes to completely saturate. Turn the shredder to Auto-On ( or FWD) mode. If required, an index card or a rigid sheet of cardstock (old greeting card or folded file folder) can be fed into the shredder to help push the jammed paper through.
- With the shredder unplugged, you may use a set needle-nose pliers or tweezers to remove the blockage.
The shredder is constantly running while in “Auto (On)” mode.| Paper
dust and other foreign objects cover the mechanical sensor. The location of
mechani cal sensor is in the middle of shredder’s feeding opening look like a
small plastic divider.| It is possible that the activation sensor, which
starts the shredder, is blocked with paper. Insert an index card or any rigid
sheet of cardstock (old greeting card or folded file folder), directly in the
center of the feed slot, while applying force to help push the jammed paper
through. This will usually clear any paper blocking the activation sensor and
feed slot.
The shredder runs in “Rev (Reverse)” mode but not in “Auto (On)” mode.|
It is also possible that the feed slot has become blocked with paper.|
Insert an index card or any rigid sheet of cardstock (old greeting card
or folded file folder), directly in the center of the feed slot, while
applying force to push the jammed paper through. This will usually clear any
paper blockage.
LIMITED WARRANTY
Warranty Period: Machines are covered by a 1-year limited warranty and cutters are warranted for 1 years from the date of your original retail purchase from us. The warranty is not transferable to any subsequent purchaser or recipient of the product. We stand by our product and offer a 30-day money-back guarantee. During this time, you could return the item without paying any extra fee if there is a manufacturing defect in it. Please rest assured that the returns are free and easy if there is a manufacturing defect. Otherwise, it would be the customer’s responsibility to cover the shipping fee. Products on sale are also returnable. If the product isn’t meeting your expectations, please email within 30-days of receipt. We will help you to either return or exchange your product. Your original form of payment will be refunded in full once the full return is complete. After 30-days orders may be subject to a 20% restocking fee and all shipping and handling charges will be the responsibility of the customer. Additional return details are listed below. After 60-days the purchase from Bonsaii is non-refundable. If you receive a damaged product, you must notify Bonsaii within 48 hours of delivery. Bonsaii will investigate the claim and notify the freight company about the damage. Please retain all packaging in the event that Bonsaii or the freight company needs to inspect it. These investigations may take several days but merchandise replacements will be processed as soon as possible. For product arrived defective or damage, We’re sorry to hear that your Bonsaii product arrived in less than perfect condition. We’d like to resolve this issue right away with the help of our Customer Support Team and Quality Assurance team. They’ll need to know a bit of information on your order as well as the issue you’re experiencing with your Bonsaii product. To report your issue, please reach out to our Customer Support team by emailing customer- care@bonsaii.com with your order number. We may need you to make a short video, or take some pictures of the defects of the product and send them to customer-care@bonsaii.com. After a preliminary analysis on the video or pictures, we will send you a brand new replacement right away if it is confirm to be defective on its arrival. If we determine that you have misrepresented Bonsaii product’s condition and that product is not defective, we will send you the right instructions and help you to use the product correctly. In line with our policy of continuous development we reserve the right to change this product, packing and documentation specification without notice. If you have any questions or any confusions, Please kindly contact with us: customer- care@bonsaii.com.
Manufacture: Bonsen Electronics Limited
: No.11-12, Lun Pin Chong Industrial Zone San Tun Community, Hou Jie Town
523941 Dongguan City, Guangdong PEOPLE’S REPUBLIC OF CHINA
Tel: 1-844-728-6917
Email : customer-care@bonsaii.com
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>