bonsaii PJ8003 720P Projector User Guide

: June 6, 2024
: Bonsaii

Table of Contents

bonsaii 720P Projector
Read User Manual Online (PDF format)
Download This Manual (PDF format)

bonsaii 720P Projector

www.bonsaiishop.com
PJ8003

1 NOTICE

How to use the projector correctly:

Do not face to lens by eyes, it will hurt your eyes from hard light of the projector when it’s working.
Do not block the air outlet, to avoid damage from internal electronic device by projector can not cooling.
Do not use chemicals, cleaner or water to clean, and also avoid rain, moisture and leucocratic liquid to corrode circuit board.
Please put the projector and accessories on the place that children can not reach.
Please make sure the projector working environment is dry and windy.
Do not place projector in too warm or too cold room, the high temperature or low temperature will shorten lifespan of the device. The working environment would be 5~35 better.
Do not put the projector in heating equipment(drying machine, microwave oven)to make it dry.
Do not press hard or put something heavy on the projector, it will damage projector.
Do not throw, beat, shake projector, it will damage circuit board in it.
Do not dismounting projector. Please contact after-sales service if you have any problem.
Do not fix by yourself. If projector can not working normaly, please consult with after-sales service or depot repair.

2 The projector and remote control

remote control
Note: please refer to the product appearance, this figure is for reference only.

Power
Arrow Keys
Confirm
Menu Button
Signal Source
Back
Lens Focussing
Keystone Correction
Media Card
Video HD Input
Audio, Video Input
Earphone/3.5mm AUDIO OUT
5V Output
Media Input/Multi-screen interface.
VGA Input
Lens
.Power Input(110-240V)

3 Projector Operation

1. Getting Started
1.1 Projector connect to power by the power line together with the projector.
1.2 According to the front of the projector or the remote control power supply button,
start the projector, indicator light becomes green, The projector is working
2. Power on/Power off
Press the “power “button on the top of the projector, or the button on the remote control, to turn on or off the projector.
3. Startup interface After power on, the boot screen appear, like the picture.

4. Keystone Correction

4.1 Vertical keystone correction (1)The vertical keystone correction is
required when æ and è below appear during the first installation and use.

4.2 Horizontal keystone correction

correction

If the picture is big in the left and small in the right, slightly swing the project to theright to correct the picture.
Please refer to the picture. It is normal if the project is slightly oblique.
If the picture is big in the right and small in the left, slightly swing the project to the left to correct the picture.

(2) Dial the keystone button left and right to adjust the picture to the quadrangle as shown in ç to finish the vertical keystone correction.

Note: Please refer to the product appearance, this figure is for reference only.

5 Image focus

Let projector be perpendicular to wall, with the Focusing button to make the
picture clear. When focusing, you can broadcasting programs to help you finsh focus.
Focusing

6. Connecting

connection

7. Network Multimedia Connect

7.1 Insert the removable storage, Media cards in thecorresponding interface.
7.2 According to the broadcast programs to choose:” photos” “music” “movie”.
7.3 Choose the file you want to play, press the key”play pause”to play or pause the file.

8. signal source selection 8.1 You can select the signal from the homepage.
8.2 Press the projector front or the remote controlsignal source key “S”, enter the
signal sourcemenu interface. Use the direction key and theconfirmation key to select the signal source.

9. AV video equipment connecting 9.1 Use the 3in 1video tieline comes with projector to connect with AV.
9.2 Choose the media signal channel :”AV”.

10. HDMI device connection
10.1 HDMI interface can be connected to the HDMI output interface equipment.
10.2 Select the corresponding signal channel: “HDMI”.
11. 3.5mm audio equipment connecting Support 3.5mm earphones and other cable soundequipment.
12. other connections Could charge the mobile phone and ipad by 5V power.

4 Multi-screen for Android phone

1 System requirements

Phone Android 4.2 model with 1GB RAM
Resolution WVGA~1080P
Storage At least 40MB free space needed

2.2 Device connection

Step 1: Select “Miracast” and press “OK” to ente miracast interface.

Step 2: Find Multi-screen/Miracast setting/software on the phone, select and connect to the Projector name shown on the projector interface. Then your phone content will be mirrored to big screen by the projector. (Note: Miracast setting and display name will differ for different phones, such as Multi- screen and Wireless Display. Pls refer to your phone for details.) wireless
display

5 Multi-screen for iPhone

1 System requirements
ios – ios 7 and above
Device – All iPhone model after iPhone 4 – All iPad model after iPad2 – All iPod touch after iPod touch 4th generation
Resolution Supported – iPhone: 480320~1136640 iPad: 1024768~20481536
Storage – At least 40MB free space needed

2 Airplay for iPhone
Step 1: Open setting menu of the phone, turn on WiFi, and connect to a certain WiFi SSID.
Step 2: Connect the projector to the same WiFi SSID which is connected by the phone. Enter “setting”, select “Network Setup”, Search for the same WiFi SSID and connect it.
Step 3: Select “Airplay” and press “OK” to enter IOS wireless connection interface.
Airplay
Step 4: Slide from the bottom of iPhone, click on Air-Play Mirroring, and select the SSID to connect for multi-screen sharing. memoring

Android Mobile: When using the mobile phone for the first time, the following interface will be called up to install “byteflymirror” according to the prompts. Interact with the screen.

allow

6 Wirecast

Step 1: Select ” Wirecast” and press “OK” to enter Wirecast interface.

wirecast interface
Step 2: Connect the phone to the projector with a data cable. IPhone: Click “Allow”or “OK” to start multi-screen sharing.
Step 3: Select “Airplay” and press “OK” to enter IOS wireless connection interface.

android mobile

7 Maintenance and Simple Troubleshooting of Projector

Smart projector is a high-tech product integrating precision optics, electronics and machinery. The improper maintenance of the projector during the daily use will affect its service life and effects. For the maintenance, important attention shall be paid to:

Dust prevention: Excessive dust will affect the heat dissipation of the projector
due to environmental impact. It is suggested to clean its dust filter for one and half months according to the actual environment.
Ventilation: As the projector integrates the sound & photo-electricity, the optical source will produce heat during its operation. Therefore, during the installation and use, it shall be ensured that no objects around will block the air inlet and outlet of the projector as the heat dissipation depends on cold air convection to improve it working stability and service life.
Lens maintenance: Lens, as the core component of the projector, is directly related to the picture definition and effect. The excessive dust thereon will affect image quality. The dirty lens shall be wiped with soft cotton cloth for the glass lens surface. Hard cloth or abrasives shall not be used.
Cleaning: Excessive dust on the projector surface shall be cleaned in a timely manner, as it will affect the heat dissipation.
Moisture protection: The projector is vulnerable to the damp air. Its operating humidity is about 45%-60%. The too damp air will affect its working stability.
Vibration prevention: The projector shall be strictly protected from strong impact, extrusion and vibration. Try not to move and knock the projector during its normal operation, which will cause the internal circuit faults.
The projector shall not be installed on the unstable, shaking and uneven desk.
The container with liquid shall not be placed on the projector.
The power shall be switched off or the power cord shall be unplugged when not in use.
Please visit www.bonsaiishop.com to register for your warranty.

8 Warranty Card

Customer’s name Contact phone Customer’s address Model(S/N) Stores address
Mr./Miss
Date of purchase
Simple Troubleshooting
Faults Power failure
The Indicator light is on but can not open projector
No signal
Screen interaction not work
Can not play online

Troubleshooting Check whether the power cord is plugged in place and the switch is on
Check whether the power cord is plugged in place and switch is on
If the signal source channel is selected correctly, please refer to the signal input port of the projector 1. Check if choose the correct mode 2. The screen jammed because the distance is too big. 3. Is the mobile connect projector SSID wifi Check the mobile and wifi connection

Warm Tips: When connected to projector via Android phone, no matter with or without USB Cable , there will be no sound from projector, sound will be only from Android phone. Please refer to Point 5 – 5.EZMirror( Screen Mirroring Interactive for Android mobile phone) in user manual if you want the sound directly from the projector. Thank you!

Projector
PJ8003
Multi-Screen QUICK GUIDE

STATEMENT
The projector is product grade A,in living Environment,the projector may cause wireless disturbance,maybe users should do something effective to avoid the disturbance.

Warning

High brightness lamp! Avoid staring or directly looking at the light,especially for children.

1.Please wash the anti-dust mesh once a month in order
to protect your projector!
Tips 2.Before using this machine,please remove the protective
membrane from the top & bottom cover.

This offer basic operation,please read the details in<Electronic- directions>from projector software application; Please read thiscarefully before use; The company reserves the right of final interpretation; Appearance of the product and the UI please please prevail; If product technology or software will upgrade, without prior notice.