truelife S600 AquaFloss Station User Manual

truelife S600 AquaFloss Station

BOX CONTENTS

• TrueLife AquaFloss Station S600
• 3× Standard nozzle, 1× Dental Plaque nozzle, 1× Orthodontic nozzle, 1× Periodontal nozzle
• Manual and safety instructions

PRODUCT DESCRIPTION

1. Nozzle storage compartment
2. Water reservoir
3. Control knob
4. Rubber suction cups
5. Storage compartment lid
6. Swivel attachment
7. Nozzle release button
8. Power button
9. Base

Nozzles

Please note: There may be residual water in the device. This is distilled water that is used when testing the device.

INSTRUCTIONS FOR USE

Remove all packaging materials before first use.
If the water flosser has been exposed to a low temperature environment during transport, leave it at room temperature for at least two hours before use.

1. Connect the nozzle to the handle. It will click when correctly inserted.
2. Remove the water reservoir from the base and fill it with water not exceeding 40 C. The capacity of the reservoir is 600 ml. Return the reservoir to the base and make sure that no water overflows.
3. Plug in the water flosser.
4. Turn the control knob to turn on the device. Turn the knob again to adjust to the desired pressure intensity.
5. Lean over the sink and put the nozzle in your mouth. Point the nozzle at your teeth and use the power button to start cleaning.
6. Leave your mouth slightly open to allow water to flow freely from your mouth into the sink. Direct the water stream at a 90° angle towards the teeth and gums. Slowly move the water stream around the teeth. Direct the water stream towards the gums and the spaces between the teeth. If you have braces, you can direct the water between the joints of the braces.
7. If you want to pause cleaning, use the power button on the handle.
8. After cleaning, switch off the device using the control knob. Open the lid of the water tank and pour out the remaining water. Switch the device on again to empty the water from the pump.

Note: To prevent the spread of bacteria, make sure that no water is left in the device. If you are not going to use the device for a long period of time, make sure it is thoroughly dried before storing it.

INSERTING/REPLACING THE NOZZLE
Insert the nozzle into the opening at the top of the flosser. When correctly inserted you’ll hear a click.

To remove the nozzle from the handle, press and hold the nozzle release button and pull the nozzle out.
The nozzles can be swivelled 360°.
The box includes the following nozzles:

• − Standard Jet – used to rinse hard-to-reach areas and places where a conven-tional toothbrush cannot reach.
  − Orthodontic Jet – a special orthodontic nozzle designed to clean and rinse hard-to-reach areas around braces.
  − Periodontal Jet – directs the stream of water or mouthwash below the gum line thanks to the tapered silicone end.
  − Dental Plaque Jet – used for more effective removal of dental plaque with easier access to affected areas.

Note: Only insert and remove the nozzles when the flosser is switched off.

Note: Nozzles are subject to personal hygiene and are not subject to warranty.

MAINTENANCE

Use only water and neutral detergents for maintenance purposes. Never use caus-tic or abrasive cleaners as they can damage the equipment. Do not use water at temperatures above 50 °C. Keep the equipment away from high temperatures and avoid direct sunlight.

1. Base
   Remove dirt by wiping it down with a towel or cloth with liquid soap and water. Then wipe it dry. Do not immerse the device in water.

2. Water reservoir
   Wash the reservoir with water and wipe with a dry cloth.
   Dry the reservoir thoroughly if you are not going to use it for a long time.
   After using a special product in the reservoir (mouthwash), rinse the reservoir each time. Partially fill the reservoir with clean warm water, direct the nozzle into the sink, turn on and let it flow until the reservoir is completely empty. Regular flushing pre-vents clogging and prolongs the life of the product.

3. Nozzles
   Wash the nozzle with water and wipe with a cloth.

TROUBLESHOOTING

SPECIFICATIONS

PRODUCT LIABILITY
TrueLife products are guaranteed to be free from manufacturing defects. In the event of such defects, elem6 s.r.o. will repair or replace the defective part or pro-duct with a comparable part or product at its sole discretion. The warranty will be deemed void if the device is altered or tampered with. The warranty does not cover damage resulting from use, accident or normal wear and tear. elem6 s.r.o. assumes no responsibility for any accident, injury, death, loss, or other claims related to or resulting from the use of this product. elem6 s.r.o. shall in no event be liable for inci-dental or consequential damages in connection with or arising from the use of this product or any of its components. Return or exchange of spare parts and / or products may be subject to shipping, handling, and replacement or replenishment fees.
This product should be stored out of the reach of children. Use by children should take place only under the direct supervision of an adult.

SAFETY GUIDELINES WHEN OPERATING THE DEVICE

1. Read the enclosed safety instructions carefully.
2. The latest version of the manual, including instructions for operating the device, can be downloaded at: www.truelife.eu.
3. Printing errors and changes of information reserved.

Manufacturer:
elem6 s.r.o.,
Braškovská 15, 16100 Prague 6, Czech Republic

References

• truelife.eu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>