MOEN GS181062B 1800 Series 33 Inch Undermount Single Basin Installation Guide
- June 9, 2024
- Moen
Table of Contents
MOEN GS181062B 1800 Series 33 Inch Undermount Single Basin Installation
Guide
HELPFUL TOOLS
For safety and ease of faucet replacement, Moen recommends the use of these
helpful tools.
Image is for reference only (Style varies by model)
Record Purchased Model Number:
OPTION A: DROP-IN SINK INSTALLATION INSTRUCTIONS
Parts List
A. Sink
B. Mounting Bolt
C. Mounting Clip
Position sink upside down on counter and trace outline.
Draw cut line 5/16″ inside the sink outline.
Drill pilot holes on cut line
Carefully cut counter hole following inside of the cut line. Remove counter material.
Install faucet and drain fittings and accessories according to manufacturer’s instructions.
Insert mounting clip (C) onto mounting bolt (B) and secure until tight
Insert mounting hardware onto sink mounting rails along each side as illustrated. 10 total mounting hardware included.
Apply a bead of caulk 1/8″-1/4″ away from edge of counter cutout.
Center sink within counter opening. Apply even pressure to all sides. Wipe away any excess caulk on counter.
Tighten installation screws in order as shown above.
Connect faucet and drain fittings.
OPTION B: UNDERMOUNT SINK INSTALLATION INSTRUCTIONS
A fabricator can use the enclosed paper pattern to create the countertop holes for sink and/or faucet.
Turn countertop upside down and align the bowl to countertop cutout.
Determine location for mounting brackets; space evenly around the underside. Mounting holes should be 1-1/8” out from the edge of the sink ledge.
Drilling and anchoring may be required at this stage of installation. Locate and drill the mounting holes (following the countertop manufacturer’s instructions) as shown. Holes should allow even spacing of mounting brackets around the sink. Type of fasteners to be as recommended by countertop supplier.
Clean underside of countertop and top rim of sink thoroughly
Apply a bead of caulk 1/8”-1/4” away from edge of counter cutout and then align sink on counter. Caulk not included. Consult your professional installer. Sealants may vary
Attach mounting hardware. Consult your professional installer. Hardware can vary. Position brackets so that bracket edge overlaps sink ledge and finish installing mounting hardware.
Tighten brackets evenly. Do not overtighten. Turn countertop and sink attached right side up.
Complete counter installation and wipe away any excess caulk from sink rim.
Connect faucet and drain fittings.
Stainless Steel Sink Cleaning Recommendations: If maintained properly, your Moen® stainless steel kitchen sink will not chip, peel, rust or discolor. The following chart illustrates our recommendations for maintaining the original appearance of your new Moen® stainless steel kitchen sink.
| SITUATION | CLEANING RECOMMENDATION |
|---|---|
| Routine Cleaning: | Soap, ammonia, detergent and water. Rub with a |
sponge or cloth followed by a thorough rinsing, then dry.
Smears and fingerprints:| Use window or glass cleaner. Rub with
a cloth.
Persistent spots and stains:| Stainless steel cleaner. Apply with a
sponge or cloth. Rub back and forth in direction of grain lines. Rinse with
clean water and dry. NOTE: Not for mirror finishes.
Hard water spots and scale:| Vinegar (full strength).
Swab and soak for 5-10 minutes. Rub, then rinse with a neutralizer such as
baking soda solution. Rinse with clean water and dry.
“Rusty” discoloration and atmospheric stains:| Use any of the
cleaning agents listed above. Swab with a cloth and soak for 5 minutes. If
necessary, rub with a nylon pad. Rinse with clean water and dry.
What not to use:| Do not use steel wool pads. This can cause rust or
pitting of the sink surface.
Moen® products have been manufactured under the highest standards of quality
and workmanship. Moen warrants to he original consumer purchaser for as long
as the original consumer purchaser owns their home (the “Warranty Period” for
homeowners), that this sink will be free from defects in materials and
manufacturing workmanship.
This warranty is extensive in that it covers replacement of all defective
parts. However, damage due to installation error, product abuse, product
misuse, or use of cleaners not in compliance with included stainless steel
sink cleaning recommendations instructions, whether performed by a contractor,
service company, or yourself, are excluded from ths warranty. Moen will not be
responsible for labor charges and/or damage incurred in installation, repair
or replacement, not for any indirect, incidental or consequential damages,
losses, injury or costs of any nature relating to this faucet. Except as
provided by law, this warranty is in lieu of and excludes all other
warranties, conditions and guarantees, whether expressed or implied, statutory
or otherwise, including without restriction those of merchantability or of
fitness for use. Some states, provinces and nations do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitations
or exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state, province to province, nation to nation.
Moen will advise you of the procedure to follow in making warranty claims.
Simply write to Moen Incorporated using the address above. Explain the defect
and include
proof of purchase and your name, address, area code and telephone number.
Moen Incorporated
25300 Al Moen Drive
North Olmsted, Ohio 44070-8022
U.S.A.
Please Contact Moen First
For Installation Help, Missing or Replacement Parts
(USA)
1-800-BUY-MOEN (1-800-289-6636)
WWW.MOEN.COM
(Canada)
1-800-465-6130
WWW.MOEN.CA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>