beper 50.161 Cordless Steam Iron Instructions

: June 8, 2024
: beper

Table of Contents

50.161 Cordless Steam Iron
Storage
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

50.161 Cordless Steam Iron
Instructions beper 50 161 Cordless Steam Iron

50.161 Cordless Steam Iron

Precautions
Read the following instructions carefully, since they give you useful safety information about installation, use and maintenance and help you avoid mishaps and possible accidents.
Remove the packing and make sure that the appliance is intact, with special attention to the supply cable.
The elements of the packing (plastic bags, polystyrene, etc) do not have to be accessible to the children, in order to preserve them from danger sources. It is recommended not to throw these packing material in the domestic waste, but to deliver them to the appropriate station of collection or destruction refusals, asking eventually information to the manager of the Sanitation Department of your own municipality.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Before connecting the appliance make sure that the mains voltage corresponds to the data specified on the label.
The appliance can be damaged if the voltage is not correct.
If the plug does not suit the socket, let it be replaced with another suitable plug by qualified personnel only, which shall also ensure that the section of the socket cables is suitable for your appliance power absorption. Generally, the use adaptors multiple plugs and/or extensions is not recommended; should they be necessary, please use only simple or multiple adaptors and extensions in compliance with the safety rules in force, making sure that the capacity absorption limit marked on the simple adaptors and the extensions and the maximum power limit marked on the multiple adaptor are not exceeded.
Do not use the appliance if the cable or the plug shows any damages.
Do not use the appliance after a possible irregular working. In this case, switch it off and do not break it open. Refer to an authorized Beper after- sale service for repair and require original spare parts only. Failing to follow these instructions may impair the safety of your appliance.
This appliance is to be destined to its special purpose only. Any other use is to be considered as improper and thus dangerous. The manufacturer cannot be responsible for any damages deriving from impro- per, wrong or incautious use.
This appliance is for household use only.
To protect against electric shock, do not immerse cord, plug or any parts of the appliance into water or other fluids.
Do not use the appliance near explosives, highly flammable materials, gases or burning flames.
Do not allow children, disabled people or every people without experience or technical ability to use the appliance if they are not properly watched over. Close supervision is necessary when any appliance used by or near children.

Description of the product Fig.A

Temperature control
Continuous steam regulation button
Steam shot button
Spray button
Spray nozzle
Temperature control light
Water tank opening
Soleplate
Tank
Holding base
Self-Clean button
Power cable
Power base
Lock/unlock selector (1= cordless use; 2= not in use; 3= use with cord)
Measuring cup

Some warnings
Steam iron is intended exclusively for ironing garments. It can only be used indoors and for private domestic use.
Any other use is to be considered non-compliant.
Always unplug the product when it is not in use, when filling or emptying the tank.
Make sure that the power cord does not come into contact with hot parts of the iron.
Do not leave the iron unattended while it is on.
Never immerse the iron and / or its components in water and / or other liquids.
Always place the iron and its base on stable and heat resistant surfaces.
Before the first use
At the first use the iron could emit a little smoke, this is normal and does not compromise the functioning of the product.
Before using the product for the first time, remove the protective film from the plate and clean it with a soft cloth.
Operate the steam jet for a few seconds on a piece of old cloth because the first use may leak some processing residues that could stain the fabric.
Before using the iron for the first time, it is necessary to charge the plate for 30 seconds.
Usage time
When using cordless iron, there are 3 possible options:
Steam shot function can work for about 1 minute;
Continuous steam function can work for about 1.5 Minutes.
Dry iron function, it can work for about 2 minutes.
Filling the water tank
Unplug the power cord from the power outlet before filling the water tank.
Keep the iron in a horizontal position.
Slowly pour the water through the appropriate hole, using the supplied measuring cup.
Be careful not to overfill the tank (see the mark), to prevent the water from escaping.
Note: the iron is designed for use with tap water, however, if the water is very hard, it is advisable to use a mixture of distilled water and tap water.
It is advisable to empty the water tank after each use, in order to avoid the formation of limescale, mold and bad odors. It is recommended to allow the iron to cool for a few minutes before emptying the tank.
Temperature selection
Always check the label with the ironing instructions on the article to be ironed and follow them.
Turn the thermostat knob to set the desired temperature, following the legend below.

SYMBOL

| FABRIC
---|---
| Do not iron
| Synthetic, Nylon, Acryilic, Rayon
| Wool, Silk
| Cotton, Flax

Steam ironing
While heating, set the steam button to zero «0»
Position the iron in a vertical position and set the temperature control to minimum.
Insert the plug into the wall socket, then turn the temperature control to maximum. The temperature control light will switch on, indicating that the iron is heating up.
When the light switch off, the set temperature has been reached and the iron is ready for use.
During ironing, the light will turn on and off automatically as the thermostat maintains the set temperature (it is still possible to continue ironing during this process).
Select the desired amount of steam, using the appropriate button. It is possible to choose between three different types of intensity (zero, one, two), the choice made is visible on the display placed in front of the spray and steam shot buttons.
The steam is produced as soon as the iron is held in a horizontal position.
Caution: take care not to come into contact with the expelled steam. Do not direct the steam jet towards people and / or animals.
Warning: if the water in the tank runs out during use, wait until the iron has cooled down before filling it again.
Warning: before using the steam, wait until the temperature has been reached, otherwise the plate may drip because the steam is not yet ready.
Spray
As long as there is enough water in the water tank, you can use the “spray” button regardless of the set temperature, and that ironing steam or dry.
When using the iron for the first time, it is advisable to press the “spray” button few times before obtaining an adequate spray, as the water must be able to fill the circulation pipes before exiting.

Steam shot
The steam shot is used to remove the most stubborn creases.
Set the thermostat knob to the position “●●” or “●●●”.
Set the steam setting button to the maximum position (two)
Press the steam shot button.
Note: to avoid water leaking from the plate, do not hold the steam shot button for more than 5 seconds continuously.
Dry ironing
The steam iron can also be used dry with or without water in the water tank. However, it would be better to avoid filling the water tank while ironing.
Set the steam control button to the minimum position (zero).
Set the temperature control to the most suitable temperature for the fabric to be ironed.
Self clean (auto-cleaning)
Fill half of the water tank.
Set the temperature control to the maximum position and the steam setting button to the minimum position.
Plug the power cord into the wall socket.
Let the iron warm up until the light switches off.
Holding the iron in a horizontal position above the sink, place the steam selector in the maximum position, press 5 times the “self clean” button.
The boiling water, the steam and the impurities will be expelled from the holes in the plate.
Unplug the power cord from the power outlet.
Wait until the iron is cold before storing it.

Anti-calc system
A special resin filter inside the water tank softens the water and prevents limescale build-up in the plate. The resin filter is permanent and does not require replacement.
Note:Do not use chemical additives, scented substances or descaling agents. Failure to comply with the above mentioned regulations will make a loss of the warranty.

Anti-drop system
With the anti-drop system, even the most delicate fabrics can be ironed perfectly and it is recommended to always iron at low temperatures.
The plate can cool down to the point where no more steam will come out, but drops of boiling water may come out and may leave marks or stains. In this case, the anti-drip system is activated automatically to prevent vaporization, so you can iron the most delicate fabrics without risking to damage or stain them.

Cord ironing

Set the lock / unlock selector to position 3.
Grip the iron with the power base and start ironing.
At the end of ironing, reposition the iron on the base and set the lock / unlock selector to position 2.

Cordless ironing

Set the lock / unlock selector to position 1.
Grip the iron without the supply base and start ironing.
Reposition the iron on the base when you are not using it.
At the end of ironing, reposition the iron on the base and set the lock / unlock selector to position 2.

Storage

Unplug the power cord from the power outlet, empty the water tank (do it after each use) and allow the iron to cool down completely.
Set the lock / unlock selector to position 2.

Technical data

Power: 2200W
Power supply: 220-240V ~ 50-60Hz
For any improvement reasons, Beper reserves the right to modify or improve the product without any notice.

The European directive 2011/65/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected.

GUARANTEE CERTIFICATE
This appliance has been checked in the factory. From the date of original purchase a 24 month guarantee applies to material and production defects. The purchase receipt and the guarantee certificate must be submitted together in case of claim to guarantee.
The guarantee is valid only with a guaranty certificate and proof of purchase (fiscal receipt) indicating the date of purchase and the model of the appliance
For any technical assistance, please contact directly the seller or our head office in order to preserve the appliance’s efficiency and NOT TO void the guarantee. Any intervention on this appliance by non-authorized persons will automatically void the guarantee.

GUARANTEE CONDITIONS
If the appliance shows defects as a result of faulty material and/or production during the period of guarantee, we guarantee repair free of charge on condition that:

The appliance has been used properly and for the purpose for which it has been intended.
The appliance has not been tampered with, otherwise it is not maintainable.
The purchase receipt shall be presented.
The appliance showing a fair wear and tear shall not be covered by this guarantee.

Therefore, any part that could be accidentally broken or having visible signs of use in consumable products (such as lamps, batteries, heating elements…) the aesthetic parts are excluded from the guarantee, and any defect whatsoever resulting from non-respect of the rules for use, negligence in usage and/or maintenance of the appliance, carelessness, wrong or improper installation, damage during transport and any other damage not attributable the supplier.
For every defect that could not be repaired within the guarantee period, the appliance will be replaced free of charge.
In any case, if the part to be replaced for defect, breakage or malfunction is an accessory and/or a detachable part of the product, Beper reserves the right to replace only the very part in question and not the entire product Contact your distributor in your country or after sales department Beper.
E-mail assistenza@beper.com which will forward your enquiries to your distributor.