MEEC TOOLS 019151 230V 260W Sheet Sander Instruction Manual

: June 8, 2024
: MEEC TOOLS

Table of Contents

MEEC TOOLS 019151 230V 260W Sheet Sander
SAFETY INSTRUCTIONS
- WORK AREA
- ELECTRICAL SAFETY
PERSONAL SAFETY
- USE AND CARE
- SERVICE
SPECIAL SAFETY INSTRUCTIONS
- SYMBOLS
- TECHNICAL DATA
DESCRIPTION
- USE
MAINTENANCE
- CLEANING THE DUST CONTAINER
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MEEC TOOLS 019151 230V 260W Sheet Sander

SAFETY INSTRUCTIONS

WARNING!
Read all the safety instructions and other instructions. Failure to follow all the instructions and safety instructions can result in the risk of electric shock, fire and/or serious personal injury. Save all warnings and instructions for future reference.
The term “power tool” in all the warnings below refers to mains-powered (corded) or battery-powered (cordless) power tools.

WORK AREA

Keep the work area clean and well lit. Dark and cluttered work areas increase the risk of accidents and injuries.
Do not use power tools in explosive environments, such as in the vicinity of flammable liquids, gas or dust. Power tools produce sparks that can ignite dust and fumes.
Keep onlookers, especially children, at a safe distance when using power tools.
You can easily lose control of the power tool if you are distracted.
The work area should be well ventilated.

ELECTRICAL SAFETY

The plug on the power tool must match the power point. Never modify the plug in any way. Never use an adapter with earthed power tools. Unmodified plugs and matching power points reduce the risk of electric shock.
Avoid body contact with earthed surfaces such as pipes, radiators, cookers and refrigerators. There is an increased risk of electric shock if your body is earthed.
Do not expose power tools to rain or moisture. There is a greater risk of electric shock if water gets into a power tool.
Be careful with the power cord. Never use the power cord to carry or pull the tool, or to pull out the plug from the mains socket. Keep the power cord away from heat, oil, sharp edges and moving parts. Damaged or tangled power cords increase the risk of electric shock.
If using the tool outdoors, only use an extension cord approved for outdoor use. Cords intended for outdoor use reduce the risk of electric shock.
If it is absolutely necessary to use power tools in damp conditions, use a mains connection protected by a residual current device (RDC). A residual current device reduces the risk of electric shock.
Do not use the tool if the power cord is damaged. Pull out the plug immediately if the cord is damaged when working. Do not pull the power cord to pull out the plug. Damaged power cords increase the risk of electric shock.

PERSONAL SAFETY

Stay alert. Pay attention to what you are doing, and use your common sense when working with power tools. Never use power tools if you are tired or under the influence of drugs, alcohol or medication. A moment of inattention or carelessness can result in serious personal injury.
Use personal safety equipment. Wear safety glasses or a visor. Depending on the type of tool and how it is used, safety equipment such as dust masks, non-slip safety shoes, safety helmets and ear protection reduce the risk of personal injury.
Avoid accidental starting. Check that the power switch is in the OFF position before plugging in the plug or battery, or lifting/carrying the tool. Carrying a power tool with your finger on the switch or connecting a tool to the mains supply when the switch is in the ON position increases the risk of accidents and injuries.
Remove adjuster keys/spanners before switching on the power tool. Spanners or the like that are left in a rotating part of the power tool can cause personal injury.
Do not overreach. Always maintain a firm footing and good balance. This ensures better control over the power tool in unexpected situations.
Wear suitable clothing. Do not wear loose-fitting clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose-fitting clothing, jewellery and long hair can get caught in moving parts.
If dust extraction and dust collection equipment is available, this should be connected and used correctly. The use of such devices can reduce the risk of dust-related problems. Clean the ventilation openings regularly.
The accumulation of metal dust can cause the metal parts of the tool to become live– risk of electric shock.
Do not allow familiarity with similar tools to lead to exaggerated self-confidence and to neglect the safety instructions for the tool. A moment of inattention or carelessness can result in serious personal injury.

USE AND CARE

Do not force the power tool. Use the correct power tool for the planned work. The tool does the job better and more safely when used at the rate for which it was designed.
Do not use the power tool if it cannot be switched on and off with the power switch. Power tools that cannot be controlled with the power switch are dangerous and must be repaired.
Pull out the plug and/or remove the battery before making any adjustments, changing accessories or putting the power tool away. These safety precautions reduce the risk of accidentally starting the power tool.
Store power tools out of the reach of children when not in use. Never allow children, or anyone who is unfamiliar with the power tool and these instructions, to use the tool. Power tools are dangerous if used by inexperienced persons.
Maintain power tools and accessories. Check that moving parts are properly adjusted and do not jam, and that no parts are incorrectly fitted or damaged. Check for other factors that could affect functionality. If a power tool is damaged it must be repaired before it is used again. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control.
Use the power tool, accessories and bits etc., in accordance with these instructions, taking into account the actual working conditions and the work that is to be done. It can be dangerous to use power tools for purposes other than those for which they are intended to be used.
Keep handles and grips clean, dry and free from oil and grease. Greasy handles and grips make it difficult to hold and control the tool in unexpected situations.

SERVICE

Power tools must only be serviced by qualified personnel using identical spare parts. This will ensure that the power tool remains safe to use.

SPECIAL SAFETY INSTRUCTIONS

Only use accessories recommended by the manufacturer. The use of other accessories can result in a risk of personal injury.
Only use the tool for dry sanding. There is an increased risk of electric shock if water enters a power tool.
Find out whether sanding the surface in question can product toxic dust and/or fumes. Dust/fumes from wood, metal and paint etc. can cause allergic reactions and/or can be harmful to health. Observe special care and avoid inhaling and skin contact with such materials. Materials that contain asbestos should only be handled by qualified personnel.
Do not put your hands under the workpiece – risk of personal injury.
Make sure there are no nails, screws or other foreign objects in the workpieces.

ADDITIONAL SAFETY INSTRUCTIONS

Hold the power tool by the insulated grips when working in areas where the tool may come into contact with concealed electrical cables or its own power cord. Contact with a live cable will cause the metal parts on the tool to also become live – risk of electric shock.
Before starting work on walls, ceilings or floors, check that there are no concealed electrical cables or conduits. Use a live wire detector, or ask an electrician for help. Failure to observe these instructions could result in the risk of fire, explosion, electric shock, personal injury and/or material damage.
Avoid accidental starting. Switch off the tool if the power supply is disconnected, e. g. as a result of a power cut or if the power cord is pulled out.
Secure the workpiece. Secure the workpiece with clamps or a vice. Never hold the workpiece with your hand.
Keep the work area clean. The mixing of dust from different materials is especially dangerous. Dust from light metals, e.g. aluminum, can ignite or explode.
Avoid overheating the tool and workpiece – risk of material damage.
Do not touch accessories during or immediately after use – risk of burn injury.
Never clean hot tools with flammable agents – risk of fire and/or explosion.
In addition to these instructions, you should always comply with local regulations and laws concerning health, safety and the environment.
Do not remove or cover symbols and markings on the product. Replace any stickers that have become illegible or lost.

VIBRATION
The total vibration value ah for the handle that vibrates most must be specified, in similarity with the uncertainty K.

Minimization of noise and vibration
To reduce noise and vibrations when in use, limit the time the tool is in use. Use power modes with low vibration mode and noise levels, and use suitable safety equipment.
Take the following precautions to minimize the risks of exposure to vibrations and/or noise.

Only use the product as it is intended to be used and in accordance with these instructions.
Make sure that the product is in good condition.
Use accessories in good condition, and which are suitable for the purpose.
Keep a firm grip on the handles/grips.
Maintain the product in accordance with these instructions and keep it well lubricated (where appropriate).

Plan the work so that exposure to heavy vibrations is spread over a longer period.

SYMBOLS

| Read the instructions.
---|---

**CE**

TECHNICAL DATA

Rated voltage 230 V ~ 50 Hz
Output 260 W
Speed, no load 13,000 rpm
Sanding pad size 93 x 185 mm
Sandpaper size 93 x 230 mm
Sound pressure level, LpA 82 dB(A), K=3 dB
Sound power level, LwA 93 dB(A), K=3 dB
Vibration level 5.4 m/s², K=1.5 m/s²
Weight 1.7 kg
Cord length 3 m

Always wear ear protection!
The declared vibration value, which has been measured by a standardized test method, can be used to compare different tools with each other and for a preliminary assessment of exposure.

WARNING!
The actual vibration level when using power tools may differ from the specified maximum value, depending on how the tool is used. It is therefore necessary to determine which safety precautions are required to protect the user, based on an estimate of exposure in actual operating conditions (taking into account all stages of the work cycle, e.g. the time when the tool is switched off and when it is idling, in addition to the start-up time).

DESCRIPTION

Sheet sander with dust collector, clamp and velcro fasteners for sandpaper, and comfortable, rubber coated grips. Three sandpapers (G60/80/120) included.

Lock button
Power switch
Dust container
End sandpaper clamp
Ventilation openings
Sandpaper clamp
Sanding pad
Front sandpaper clamp
Front handle
Ventilation openings
Main handle
FIG. 1

USE

FITTING SANDPAPER

Lift the sandpaper clamps (6) up and out. The clamps are located on each side of the Sheet sander. This releases the front and end sandpaper clamps (4 and 8) on the bottom part of the sander.
Put one end of the sandpaper with the rough side up in the open front sandpaper clamp (8) and check that it is in line with the sanding pad. Lift the sandpaper clamp up and in to clamp the sandpaper in place.
Fold the sandpaper over the sanding pad and insert it in the open end sandpaper clamp (4).
NOTE: Make sure that the sandpaper is stretched as tight as possible against the sanding pad for best possible sanding.
Lift the sandpaper clamp up and in to clamp the sandpaper in place.

MAKING HOLES IN THE SANDPAPER
If a sandpaper without holes has been fitted, you can make holes yourself. Place the corner of the bottom part of the sander in the hole punch with the corner (1) fully inserted in the corner of the hole punch (2). Press down the bottom part firmly in the hole punch. The sharp punches (3) make holes in the sandpaper (4) to remove the dust.
FIG. 2

STARTING/SWITCHING OFF

Start the sander by pressing the power switch (2).
Switch off by releasing the power switch (2).

LOCK BUTTON
The sander has a locking function, which is handy when sanding continuously for longer periods.

Lock the sander by first pressing the power switch (2) and then pressing the lock button (1).
Release the power switch and release the lock button. The sander will now continue to run.
Switch off the sander by pressing and then releasing the power switch to interrupt the locking function.

SELECTING SANDPAPER

To get the best possible result it is very important to choose the right grade and type of sandpaper. Aluminium oxide, silicon carbide and other synthetic abrasives are best for tool sanding. Natural abrasives such as flint and granite are too soft and not suitable for tool sanding.
Coarse sandpaper removes a lot of material, while fine sandpaper produces a smoother surface after sanding. The best sandpaper to use depends on the condition of the surface to be sanded.

NOTE:

The grade of sandpaper is often indicated by a number, where a higher number indicates fine sandpaper and a smaller number coarse sandpaper.
If the surface to be sanded is very rough, start with a coarse sandpaper. Use a medium coarse sandpaper afterwards to remove scratching from the coarse sandpaper, and then a fine sandpaper to produce a smooth surface. Continue sanding until the surface is uniformly smooth.

SANDING
Clamp or fasten the workpiece so that it cannot move during the sanding. Use a vice if possible.

WARNING!
If the workpiece is not secured it can be thrown towards the user and cause injury.
Place the sander so that the surface of the sanding pad is in full contact with the workpiece. Start the sander by pressing the power switch. Move the sander slowly over the workpiece, working with parallel strokes until all of it has been sanded. When sanding wood it is important to move the sander parallel to the grain, not across it. This makes the sanding more effective and produces a smoother surface. Switch off the sander by releasing the power switch after sanding. Do not remove the sanding pad from the workpiece until the sander has stopped.

NOTE:

Do not start the sander until all of the sanding pad is in contact with the workpiece. The sandpaper can come loose if the full surface is not in contact with the workpiece, which can result in damage.
Hold the sander with both handles, with both hands. Do not cover the ventilation openings on the motor with your hands. Covering the ventilation openings can overheat and damage the motor.

Do not force the sander. The weight of the sander is normally enough to achieve sufficient pressure. Allow the sander and the sandpaper to do the job. Pressing the sander will make the motor and the sanding slower, and wear out the sandpaper quicker. Too much pressure can overheat and damage the motor. It will also reduce the quality of the sanded surface. Surface treatment products on the wood
(polish, varnish etc.) will soften as a result of frictional heat, which can quickly reduce the efficiency of the sandpaper. Do not sand in the same place for too long, this can sand off too much material and produce an uneven surface.
Sanding continuously for long periods without a break can cause the motor to overheat. If this happens, switch off the sander and wait until the sanding pad stops, and then lift it off the workpiece. Check that the ventilation openings are open (not covered by your hands during the work). Allow the motor to cool before resuming.

MAINTENANCE

CLEANING THE DUST CONTAINER

The dust container collects most of the dust produced during the work. The container must therefore be emptied at regular intervals to make the collection of dust effective.

Press the sides of the dust container (1) and pull it out from the end of the sander (2).
FIG. 3
Pull the top part of dust container (3) loose from the bottom part (4).
NOTE: Open the dust container outdoors or over a paper bag or dustbin, because the dusts comes straight out.
FIG. 4
Shake out all the dust from the dust container.
Use a soft, dry brush to remove dust from the filter inside the top part.
Put the dust container back together again after emptying it. The parts click in place when put together correctly.
Replace the dust container on the back of the sander.

NOTE: The tabs (5) snap in place when the dust container is pushed in the back of the sander.

General
Do not use solvent to clean the plastic parts. The plastic can be damaged by different types of commercially available solvent. Use a clean cloth to remove dirt, dust, oil and grease etc.
Power tools wear out more quickly if they are used for fibreglass, plaster or putty. Dust from these materials puts strain on bearings, brushes and commutators. It is therefore not recommended to use the sander for more extensive work on fibreglass materials, plaster or putty. If the sander is used to sand any of these materials it is very important to clean it often with compressed air.

LUBRICATION
All the bearings in this Sheet sander are lubricated with high quality lubricant and this lubricant is intended to last for the entire life span of the sander in normal conditions. No further lubrication is therefore necessary.