HID PLT-02395 OMNIKEY Smart Card Readers Installation Guide

HID PLT-02395 OMNIKEY Smart Card Readers

Product Information

and mobile usage.
3021 USB| High-performance smart card reader, with a USB interface and
small form factor for desktop and mobile usage.
3121 USB| High-performance smart card reader for desktop use with
multiple standing base options in a robust housing.
5021 USB| Contactless Reader with USB interface for desktop use that
reads/writes to 13.56 MHz smart cards.
5022 USB| Contactless Reader with USB CCID-compliant interface for
desktop use that reads/writes to 13.56 MHz smart cards.
5023 USB| A 5022 Reader with iCLASS and Seos support.
5027 USB| A 5023 Reader with Keyboard wedge.
5025 CL USB| Contactless Reader with USB CCID-compliant interface for
desktop use that reads contactless (125 kHz) Prox cards.
5127 / 5427 CK/ 5427 UE USB| Contactless 13.56MHz/125kHz reader with CCID/Keyboard wedge
interface.
5421 / 5422 USB| Dual interface PC-linked reader that reads/writes to 13.56 MHz
contactless cards and virtually any contact smart card. 5422
includes CCID.
6121 Mobile USB| Dongle-sized smart card reader for SIM-sized smart cards,
especially well suited for use with mobile devices.

Product Usage Instructions

Parts

• Find drivers, reader documentation supporting various operating systems at: www.hidglobal.com/omnikey
• See the application note for card loading and handling instructions at: www.hidglobal.com/omnikey

Specifications and Installation:

For further information, contact HID support: www.hidglobal.com/support.
For driver setup, consult the OMNIKEY Smart Card User Guide.

CAUTION:
Install the drivers prior to attaching the OMNIKEY reader with the computer.

USB Connected Reader Specifications

USB Connected Reader Installation

1. Connect the reader with computer; plug the USB connector into your computer’s USB port.
2. When the reader is operational, the LED illuminates.
3. For contactless operation, hold the card next to the reader logo. For contact smart cards, insert the card into the reader with contacts facing up.
4. The LED blinks when the reader is exchanging data with a card (reading/writing).

Regulatory
CAUTION:
Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

FCC (All Readers)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

© 2010-2017 HID Global Corporation/ASSA ABLOY AB. All rights reserved. This document may not be reproduced, disseminated or republished in any form without the prior written permission of HID Global Corporation. HID Global, HID, the HID logo, iCLASS SE, OMNIKEY, and Seos are the trademarks or registered trademarks of HID Global Corporation, or its licensors, in the U.S. and other countries.

Introduction

This guide describes physical behavior and conformities of the OMNIKEY Smart Card Readers.

• 1021 USB – Desktop smart card reader in a small form factor for desktop and mobile usage.
• 3021 USB – High-performance smart card reader, with a USB interface and small form factor for desktop and mobile usage.
• 3121 USB – High-performance smart card reader for desktop use with multiple standing base options in a robust housing.
• 5021 USB – Contactless Reader with USB interface for desktop use that reads/writes to 13.56 MHz smart cards.
• 5022 USB – Contactless Reader with USB CCID-compliant interface for desktop use that reads/writes to 13.56 MHz smart cards.
• 5023 USB – A 5022 Reader with iCLASS and Seos support.
• 5027 USB – A 5023 Reader with Keyboard wedge.
• 5025 CL USB – Contactless Reader with USB CCID-compliant interface for desktop use that reads contactless (125 kHz) Prox cards.
• 5127 / 5427 CK/ 5427 UE USB – Contactless 13.56MHz/125kHz reader with CCID/Keyboard wedge interface.
• 5421 / 5422 USB – Dual interface PC-linked reader that reads/writes to 13.56 MHz contactless cards and virtually any contact smart card. 5422 includes CCID.
• 6121 Mobile USB – Dongle-sized smart card reader for SIM-sized smart cards, especially well suited for use with mobile devices.

Parts

• Smart Card Reader
• Installation Guide

Find drivers, reader documentation supporting various operating systems at: www.hidglobal.com/omnikey
See the application note for card loading and handling instructions at: www.hidglobal.com/omnikey

eBase Models
1021, 3021, 3121, 5021,
5022, 5023, 5025, 5027,
5127, 5421, 5422, 5427, 6121
Drivers and Manuals: www.hidglobal.com/omnikey

Americas and Corporate
611 Center Ridge Drive
Austin, TX 78753
USA

Europe, Middle East and Africa
Phoenix Road
Haverhill, Suffolk CB9 7AE England

Asia Pacific
19/F 625 King’s Road North Point, Island East Hong Kong
www.hidglobal.com/support

Specifications and Installation

For further information, contact HID support: www.hidglobal.com/support.
For driver setup, consult the OMNIKEY Smart Card User Guide.
CAUTION : Install the drivers prior to attaching the OMNIKEY reader with the computer.
ATTENTON: Vous devez installer le driver avant de connecter le lecteur OMNIKEY à l’ordinateur.

USB Connected Reader Specifications

5022, 5023, 5027, 5422
78.7 in/200 cm – Models 5021, 5025 CL, , 5427 CK
70.9 in/180 cm – Other Models
Mean Time Between Failures (MTBF)| 500,000 Hours
Host Interface| USB 2.0 CCID (USB 1.1 Compatible)
Host Data Transmission Speed| 12 Mbps (USB 2.0 Full Speed)
Power Supply| Bus Powered

USB Connected Reader Installation

1. Connect the reader with computer; plug the USB connector into your computer’s USB port.
2. When the reader is operational, the LED illuminates.
3. For contactless operation, hold the card next to the reader logo. For contact smart cards, insert the card into the reader with contacts facing up.
4. The LED blinks when the reader is exchanging data with a card (reading/writing).

Regulatory

CAUTION: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

FCC (All Readers)
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Product Radio Certifications
The OMNIKEY 5022 CL and 5127CK MINI Module were tested under the FCC rules and Industry Canada rules for a Modular Approval and therefore the following shall apply: (reference below FCC/IC IDs)

• Provided that the Antenna and tuning network have not been changed
  in any way, the Final Product label may contain the HIID Global FCC ID. Provided no other radio devices exist within the final assembly. The end integrator may use these ID’s, as long at the original HID Global Label is visible.

• FCC ID: JQ6-OK5022CL or IC ID: 2236B-OK5022CL

• FCC ID: JQ6-OK5127CKMINI or IC ID: 2236B-OK5127CKMINI

• The End User/Manufacturer, will not need to repeat the intentional emissions testing (actual radio certification), however the un-intentional emissions testing will need to meet the FCC and IC requirements with the module installed into the final assembly or product. This also applies to CE Marking as defined by the R&TTE Directive.

• However, in many cases, the module may need to be retuned, due to the effects of the product enclosure and assemblies within this enclosure, and the de-tuning affect that this may have on the radio circuitry. In this case and if other radios exist, Class 2 Permissive Change is required.

• In the event that the HID OEM modules Kit is modified in any way, the radio transmitter operating at either 125 kHz, 13.56 MHz and Bluetooth, when the module is integrated into the OEM’s final product, Radio Certification is required for the final product.

• Obtain FCC Certification by submitting the final product to a Telecommunications Certified Body (TCB) laboratory that performs the testing and issue the FCC Grant. Standard: Part 15, Subpart C.

• Often the same TCB tests to Canada requirements and grants certification as a Certification Body (CB). Standard: RSS-210, RSS-GEN and RSS-310, where applicable.

• The same laboratory may also be an EU Communications Assessment Body (CAB) that is accredited to test to R&TTE Directive requirements for CE Marking. Applicable standards:
  EN 300 330, EN 301 489-3, EN 50130-4, and IEC60950.

• A laboratory that is a CAB testing to R&TTE Directive requirements will also be testing to Australia and New Zealand requirements because of a common test standard. Standard:
  AS/NZS 4268.

• Asian country certifications are obtained on an individual country basis.

OEM Final Product US Dept. of Commerce Bureau of Industry and Security (BIS) approval is required for USA based companies who export and re-export products using encryption.
Regulatory Compliance Assistance – HID Global provides technical assistance and laboratory recommendations, as required.

CAUTION: Any changes or modifications to this devise not explicitly approved by the manufacturer could void your authority to operate this equipment.

Canada Radio Certification (All Readers)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

CE Marking (All Readers)

Global hereby declares that these proximity readers are in compliance with the essential requirements and other relevant provisions of Directive 2006/95/EC.
Download the R&TTE Declaration of Conformity (DoC) at: http://www.hidglobal.com/certifications
Brazil (Readers 5022, 5023, 5422 and 5427G 2)
Chile (Readers 5022, 5422 and 5427G 2)
China (Readers 1021, 5022, 5422, 5427 and 5427G 2)
Hong Kong (Readers 5022, 5023, 5422 and 5427G 2)
India (Readers 5022, 5023, 5422 and 5427G 2)
Japan MIC (Reader 4121)
Korean KC (Readers 1021, 3121, 4040, 4321, 5021, 5022, 5325, 5326, 5421, 5422, 5427, 5427G 2, 6121, 6221, 6321)
Mexico (Readers 5022, 5023, 5422, 5427G 2) Singapore (Reader 5427 CK)
Taiwan (Readers 5321 and 5421)
According to “Administrative Regulations on Low Power Radio Waves Radiated Devices” Without permission granted by the NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to an approved low power radio- frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act.
The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices.

References

• Certifications | HID Global
• Search | HID Global
• Need Support? | Support
• HID OMNIKEY Smart Card Readers | CardLogix Corporation
• HID Global Solutions | CardLogix Corporation
• HID OMNIKEY 3021 USB Smart Card Reader | CardLogix Corporation
• HID OMNIKEY® 5023 CL Desktop Contactless Smart Card Reader
• HID OMNIKEY® 5321 Dual-Interface Smart Card Reader | CardLogix
• HD Omnikey 6121 USB Dongle SIM/GSM Card Reader - CardLogix
• HID OMNIKEY 3121 Smart Card Reader/Writer | CardLogix Corp.
• OMNIKEY 5025 CL Contactless (125 kHz) Desktop Reader | CardLogix
• HID OMNIKEY® 5422 Contact / Contactless Smart Card Reader

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>