MEEC TOOLS 082-207 Spray Gun Instruction Manual
- June 4, 2024
- MEEC TOOLS
Table of Contents
Instruction Manual
082–207
Operating instructions for spray gun
Translation of the original instructions
DECLARATION OF CONFORMITY
Jula AB, Box 363, SE-532 24 SKARA, SWEDEN
This declaration of conformity is issued under the sole responsibility of the manufacturer.
SPRAY GUN
WF-21S Max 4bar
| Directive/Regulation | Harmonized standard |
|---|---|
| MD 2006/42/EC | EN 1953:2013 |
This product was CE marked in the year
Skara 2014-08-19
Bo Eriksson
BUSINESS AREA MANAGER (Signatory for Jula and authorized to compile the
technic documentation.
Read the Operating Instructions carefully before use!
TECHNICAL DATA
| Nozzle | 1.5 mm |
|---|---|
| Connection | 1/4″ |
| Working pressure | 4,0 bar |
| Air consumption | 85-200 l/min |
| Sound pressure level, LpA | 85 dB(A), K=3 dB |
| Sound power level, LwA | 96 dB(A), K=3 dB |
| Vibration level | <2,5 m/s², K=1,5 m/s² |
Always use hearing protection!
OPERATION
- Screw the paint container and air hose firmly on the spray gun.
- Suitable air pressure depends on the viscosity of the paint and the type of work. 3 to 3.5 bar is suitable for most applications.
- A suitable distance between the spray gun and the workpiece is 15-20 cm. Inappropriate distance and spray patterns produce inferior results.
- Adjust the paint flow and air flow knobs.
MAINTENANCE
- Steep the paint gun body in clean solvent and brush it clean.
- Dismantle the air cap and paint nozzle, dip them in solvent and brush them clean.
- Be careful not to damage the holes in the nozzles.
- Spray some solvent through the spray gun to clean the paint ducts.
- Adjust the needle seal while you squeeze the trigger and check how the paint needle moves. Do not over-tighten.
TROUBLESHOOTING
| Fault | Possible cause | Action |
|---|
Uneven coating
| 1. A worn needle seal means that air is leaking into the paint duct.
2. The paint connection is loose or damaged.
3. The paint container’s nut is loose, allowing air to leak in.| 1. Replace
the O-ring or tighten the seal screw.
2. Tighten or replace.
3. Tighten.
Thicker on the sides, thinner in the middle| 1. The air cap’s square holes
are partially clogged.
2. Solid containments in the upper part of the paint nozzle.| 1. Clean the
hole. Do not use metal wire or hard objects.
Pattern| 1. The air cap’s square holes are partially clogged.| 1. Clean the
hole.
Thicker in the middle| 1. Too high air pressure by the air cap’s square
holes.
2. Paint viscosity too low.| 1. Lower the air pressure.
2. Adjust the viscosity of the paint.
---|---|---
Thick coating| 1. The gap between the outside of the paint nozzle and the air
cap is too big due to wear.
2. Too low air pressure by the air cap’s square holes.
3. Paint viscosity too high.| 1. Replace.
2. Increase the air pressure.
3. Adjust the viscosity of the paint.
Care for the environment!
Recycle discarded products in accordance with local regulations.
Jula reserves the right to make changes.
For the latest version of operating instructions, see
www.jula.com
Jula AB, Box 363, SE-532 24 SKARA
2022-01-13
© Jula AB
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>