kogan OVTHEOBFKGA Theodore Bed Frame User Guide
- June 9, 2024
- Kogan
Table of Contents
kogan OVTHEOBFKGA Theodore Bed Frame
COMPONENTS
-
A Headboard (x1)
-
B Footboard (x1)
-
C Upper sideboard (x2)
-
D Lower sideboard (x2)
-
E Upper slat support (x2)
-
F Lower slat support (x2)
-
G Sideboard leg support (x2)
-
H Leg support (x4)
-
I Horizontal slat support (x1)
-
J Sideboard rail (x4)
-
K Leg (x4)
Hardware
-
Allen key (x1)
-
50mm M8 screw (x2)
-
Nut (x10)
-
20mm M8 screw (x20)
-
40mm M4 screw (x4)
-
40mm M8 screw (x16)
-
Washer (x20)
-
T-handle Allen key (x1)
-
Slat (x36)
-
Inner cap (x24)
-
End cap (x24)
-
Screwdriver (x1)
BEFORE ASSEMBLY
Remove all components from the packaging and check all components are
accounted for.
If any components are missing, contact help.Kogan.com
for assistance.
ASSEMBLY
-
Step 1 : Secure four legs (K) onto the headboard (A) and footboard (B).
-
Step 2: Align one sideboard rail (J) with one lower sideboard (D). Place a washer (7) over the hole at the end of the sideboard rail (J), then using the Allen key (1), secure a 40mm M8 screw (6) through the washer (7).
Using the screwdriver (12), secure a 40mm M4 screw (5) through the middle hole.
Repeat this process one more time to create two lower sideboard assemblies.
-
Step 3: Align one sideboard rail (J) with one upper sideboard (C). Place a washer (7) over the hole at the end of the sideboard rail (J), then using the Allen key (1), secure a 40mm M8 screw (6) through the washer (7).
Using the screwdriver (12), secure a 40mm M4 screw (5) through the middle hole.
Repeat this process one more time to create two upper sideboard assemblies.
-
Step 4: Align one lower and upper sideboard assemblies with a sideboard leg support (G), ensuring the sideboard leg support (G) is fitted behind the sideboard rails (J).
Place two washers (7) over the upper holes of the sideboard leg support (G), then using the Allen key (1), secure two 40mm M8 screws (6) through the washers (7). Using the Allen key (1), secure the lower holes with two 20mm M8 screws (4).
Repeat this process with the remaining lower and upper sideboard assemblies to create two sideboard assemblies.
-
Step 5: Connect one lower slat support (F) with one upper slat support (E), then align the holes of two leg supports (H) with the lower and upper slat supports (F, E).
Place four washers (7) over the holes, then using the Allen key (1), secure four 40mm M8 screws (6) through the washers (7). Using the T-handle Allen key (8), secure the underside of the holes with four nuts (3).
Repeat this process with the other lower and upper slat supports (E, F) to create two slat support assemblies.
-
Step 6: Align the brackets on the sideboard assemblies with the headboard (A) and footboard (B). Using the Allen key (1), secure the brackets with eight 20mm M8 screws (4).
- Step 7: Align the slat support assemblies with the headboard (A) and footboard (B). Using the Allen key (1), secure the slat support assemblies with eight 20mm M8 screws (4).
-
Step 8: Align the horizontal slat support (I) with the sideboard assemblies. On the ends of the horizontal slat support (I), place two washers (7) over the holes on one side, then using the Allen key (1), secure two 50mm M8 screws (2) through the washers (7). The screws (2) should now be protruding out the other side.
On the other side, secure two washers (7) and two nuts (3) over the screws (2) using the T-handle Allen key (8).
-
Step 9: Connect two slats (9) with two end caps (11) and two inner caps (10) to create a slat assembly. Repeat this process until you have twelve slat assemblies.
Secure the slat assemblies by aligning the holes on the end caps (11) and inner caps (10) with the markers on the bed.
CUSTOMER SERVICE
Need more information?
We hope that this user guide has given you the assistance needed for a simple
set-up.
For the most up-to-date guide for your product, as well as any additional
assistance you may require, head online to
help.kogan.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>