Kogan KAWLMFM55MA Tilt Extendable Full Motion Wall Mount User Guide
- October 30, 2023
- Kogan
Table of Contents
KOGAN TILT EXTENDABLE
FULL MOTION WALL MOUNT
(SUITABLE FOR 23” – 55” TVS)
KAWLMFM55MA
SAFETY & WARNINGS
Read the entire instruction manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings,
contact your local distributor for assistance.
CAUTION: Use with products heavier than the rated weights indicated may
result in instability causing possible injury.
- Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Never exceed the maximum load capacity of 30kg or it may result in product failure or personal injury.
IMPORTANT: Ensure that you have received all parts according to the
component checklist prior to installation. If any parts are missing or faulty,
contact your place of purchase for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular
intervals (at least every three months).
VESA Compatible
0017×0017 002)(0017 OOZXOOt 00Ex00E 00Zx00E 00Zx0OZ 00lx0OZ 00Zx001. 000(001.
COMPONENTS
Tools required for installation (not supplied)
INSTALLING MOUNT TO WALL
Step 1
Extend the bracket / wall mount (A) out to full length.
Step 2
Using a Phillips head screwdriver (not supplied), unscrew and remove the 3mm
screws attaching the arm of the mount to the bracket. Keep these screws nearby
for later use.
Step 3
Using a pencil, spirit level, mark the desired position for the mount on your
wall, using the wall mount to serve as a stencil for the hole positions. If
mounting on dry wall or plasterboard, use a stud finder first to check
positions of wall studs and ensure the position is free from electrical
wiring. Using a drill, create the pilot holes.
Drywall / plaster: Use a ø4.5mm or 3/16” drill bit, drilling 55mm deep.
Masonry / concrete: Use a ø10mm or 3/8” drill bit, drilling 60mm deep.
Step 4
Drywall / plaster: Position the wall mount in line with the pilot holes and
secure to the wall using washers (W-C) and ST6.3 screws (W-A). Do not use the
wall anchors.
Masonry / concrete: Insert wall anchors (W-B) into the drilled holes. Position
the wall mount in line with the holes and secure to the wall using washers
(W-C) and ST6.3 screws (W-A).
INSTALLING BRACKET TO TV
VESA: 100×100; 100×200; 200×100; 200×200
Align the bracket with your TV’s VESA holes and secure using supplied screws
(M-A or M-B, depending on required length).
Check if spacers (M-C) are required to ensure correct length of screw, as per the below image. Failure to follow this step may result in damage to your TV or wall mount.
VESA: 300×200; 300×300; 400×200; 400×300; 400×400
For larger VESA configurations, attach the extension arms (B) to the bracket
using the bolt and nut set (C, D), tightening with the included spanner (E).
Align the bracket with your TV’s VESA holes and secure using supplied screws
(M-A or M-B, depending on required length).
With the extension arms successfully fitted, align the bracket with your TV’s VESA holes and secure using supplied screws (M-A or M-B, depending on required length).
Check if spacers (M-C) are required to ensure correct length of screw, as per the below image. Failure to follow this step may result in damage to your TV or wall mount.
VESA: 300×200; 300×300; 400×200; 400×300; 400×400
For larger VESA configurations, attach the extension arms (B) to the bracket
using the bolt and nut set (C, D), tightening with the included spanner (E).
Align the bracket with your TV’s VESA holes and secure using supplied screws
(M-A or M-B, depending on required length).
With the extension arms successfully fitted, align the bracket with your TV’s VESA holes and secure using supplied screws (M-A or M-B, depending on required length).
Check if spacers (M-C) are required to ensure correct length of screw, as per the below image. Failure to follow this step may result in damage to your TV or wall mount.
SECURING TV TO MOUNT
With the top two screws (from Step 2) loosely in place, hook the TV with
bracket installed onto the wall mount arm. Two people should carry the TV to
prevent damage.
Once in place, attach the lower two screws, then tighten all four. Do not
overtighten.
To set the TV to a
vertical angle, loosen the lower two screws and move the bracket into desired
position before retightening. Do not overtighten.
Add the TV’s cables to the cable management clip.
Need more information?
We hope that this user guide has given you the assistance needed for a simple
set-up.
For the most up-to-date guide for your product, as well as any additional
assistance you may require,
head online to h elp.kogan.com
kogan.com
Documents / Resources
|
Kogan KAWLMFM55MA Tilt Extendable Full Motion Wall
Mount
[pdf] User Guide
KAWLMFM55MA Tilt Extendable Full Motion Wall Mount, KAWLMFM55MA, Tilt
Extendable Full Motion Wall Mount, Extendable Full Motion Wall Mount, Full
Motion Wall Mount, Motion Wall Mount, Wall Mount, Mount
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>