insinkerator Hot250 Instant Hot Water Dispenser System Instruction Manual

CAUTION
HOT! This system can dispense near boiling water. Care and supervision should be taken to avoid scalding.

Hot250

Instant Hot Water Dispenser System

Installation, Care & Use

Welcome and thank you for purchasing this InSinkErator instant hot water system.

WHAT YOU SHOULD KNOW BEFORE YOU BEGIN

For your satisfaction and safety, read all instructions, ! cautions and warnings before installing or using this dispenser.

• This unit is not intended for commercial/industrial use.

SYSTEM REQUIREMENTS (HOT WATER TANK, DISPENSER FAUCET AND OPTIONAL

FILTRATION SYSTEM):

• Make sure that all electrical, plumbing and connections conform to local codes.
• A standard, earthed (grounded), ground fault circuit interrupter (GFCI) electrical outlet is required under the sink for the instant hot water dispenser’s electrical power. The wall outlet powering your hot water tank must have power supplied to it continuously.
• Do not install faucet backwards. Ensure red and blue indicators are forward-facing. Make sure handles activate forward, towards user.
• This GFCI outlet must be fused and should not be controlled by the same wall switch that operates the disposer unless you have a SinkTop Switch™ from InSinkErator®. Fuse/circuit breaker required is 15 amp for 120 volt and 10 amp for 230 or 220-240 volt.
• Attach filtration system to cold water supply only. The maximum operating water temperature of this system is 100°F (38°C). Do not install the filter on hot water supply lines. (Filter sold separately).
• It is recommended that a dedicated control valve be installed on the cold water line supplying water to this system.
• To prevent damage or unit not operating properly, the water pressure must be between 15 psi – 80 psi (1 bar ­- 5.5 bar; 103 kPa ­-552 kPa). Ambient (room) temperature between 40°F (4°C) and 110°F (43°C).
• Do not install if water pressure exceeds 80 psi (860 kPa).
• The use of a water filter should NOT result in the water pressure dropping below 15 psi (210 kPa).
• Do not install where water hammer conditions occur. If water hammer conditions exist you must install a water hammer arrester.
• The flexible vent and outlet tubes must be correctly connected to the dispenser supplied by the manufacturer. They must not be obstructed or connected to a normal type dispenser or any other type.
• To protect from freezing, shut off water supply, remove filter cartridge, drain hot water tank and tubing when temperatures are expected to drop below 40° F (4° C).
• Do not use a torch or other high temperature sources near system, cartridges, plastic fittings or plastic plumbing.
• Do not install near water pipes which will be in path of a drilling tool when selecting the position to mount the components.
• Mount system in such a position as to prevent it from being struck by other items used in the area of installation.
• Ensure that the location and fasteners will support the weight of the system when installed and full of water.
• When mounting tank and filter, screws provided are for use in wood studs or cabinets only. Use wall anchors (not supplied) for installation into plasterboard.
• Ensure all tubing and fittings are secure and free of leaks.
• Filtration system intended for use with plastic water lines (such as PEX tubing, PE Tubing, PP Tubing). Do not install using rigid piping. (Filtration system sold separately).
• For systems using two handle HC model dispensers, operate only one handle at a time.
• Important: Do not allow unit to continuously boil.
• Regularly inspect the system. If there are signs of water leakage, turn off the water supply and contact InSinkErator.
• A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage.
• If you suspect elevated levels of chlorine in your water, or your water has a rusty appearance before the installation of this unit, use of InSinkErator’s water filtration system is recommended.
• This product contains stainless steel. The manufacturer cannot guarantee against rusty water because of the number of factors that are involved beyond the manufacturer’s control. However, the sudden appearance of rusty water discharged from the hot water dispenser may indicate the need for service or replacement of this product.
• Moving parts inside the tank causing a rattling noise are normal.
• For questions or concerns, please contact InSinkErator (see back page for contact information).

ADDITIONAL CONSIDERATION WHEN UTILIZING INSINKERATOR’S FILTRATION

SYSTEM:

• The disposable filter cartridge MUST be replaced every 6 months, at the rated capacity or sooner if a noticeable reduction in flow rate occurs.
• Failure to replace the disposable filter cartridge at recommended intervals may lead to reduced filter performance and cracks in the filter housing, causing water leakage or flooding.
• After the recommended usage life, the filter should be disposed of per applicable rules and regulations.
• Do not install filtration system if any of the quick connect collets are missing from the filter head or Y-Quick Connector. Connect InSinkErator if collets are missing from any fittings.
• To protect from freezing, remove filter cartridge when temperatures are expected to drop below 40° F (4° C).
• Do not install systems in areas where ambient temperatures may go above 110° F (43° C).
• Do not install in direct sunlight or outdoors.
• Use this hot water tank and dispenser system only for its intended use as described in the manual.

IMPORTANT SAFETY INFORMATION

Save these instructions.

WARNING
A potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION
A potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

NOTICE
Notice is used to address practices not related to personal injury.

• This system can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the system in a safe way and understand the hazards involved. Children shall not play with the system. Cleaning and user maintenance shall not be made by children without supervision.
• Do not operate this product if it has been or appears to be damaged in any manner or after the product malfunctions or is dropped. Return the complete product immediately to your retailer or dealer for inspection.
• If the tank supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

WARNING: To reduce the risk associated with choking:
Do not allow children under 3 years of age to have access to small parts during the installation of this product.

WARNING: Electric Shock Hazard. To reduce the risk of electric shock, do not immerse or expose the product, flexible cord or plug to rain, moisture or any liquid or when standing in or on damp or wet surfaces. If any electrical product falls into water, UNPLUG it immediately. DO NOT REACH INTO THE WATER. Important: Prior to reconnecting to the power supply, the product should be inspected by a qualified technician.

WARNING: Personal Injury/Property Damage. To reduce the risk associated with hazardous voltage due to an installer drilling through existing electric wiring in the area of installation: Do not install near electric wiring or water pipes which may be in path of a drilling tool when selecting the position to mount the system bracket.

IMPORTANT
Always arrange the power cord so that it cannot come in contact with hot surfaces.

• Do not disconnect the product from the power supply by pulling on the cord.
• Do not coil power cord.
• The use of accessory attachments (i.e. power cords and power plug adapters) other than those recommended by the manufacturer may cause safety hazards.

WARNING: Electric Shock Hazard. Using an ungrounded (no earth ground) or improperly connected appliance can result in serious injury or death from electrical shock.

This appliance must be earthed (grounded). This instant hot water tank is equipped with a cord that has a grounding conductor and earth ground pin. The plug must be connected to an appropriate GFCI outlet that is properly installed and earthed (grounded) in accordance with all local codes and ordinances. Do not modify the plug provided with the appliance ­ if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Check with a qualified electrician or tradesperson if you are in doubt as to whether the instant hot water tank is properly earthed (grounded).

CAUTION: Personal Injury/Property Damage.
This tank is a non-pressurized tank. DO NOT modify this system. DO NOT close vent tube or connect other types of dispensers or valves to the tank. Use only the InSinkErator dispenser supplied. Use only parts provided. Contact InSinkErator for repairs or replacement components.

CAUTION: HOT! This system can dispense near boiling water. Care and supervision should be taken to avoid scalding. Expose only items capable of safely withstanding the selected near boiling water settings.

WARNING: To reduce the risk associated with the ingestion of contaminants: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

An instant hot water tank, like any water heater, has a limited life and will eventually fail. To avoid possible property damage and personal injury, this instant hot water tank should be regularly examined for leakage and/or corrosion and replaced when necessary. A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage.

WARNING: Fire Hazard. To minimize possibility of fire, DO NOT store flammable items such as rags, paper or aerosol cans near the tank. DO NOT store or use petrol or other flammable vapors and liquids in the vicinity of this or any other appliance.

WARNING: Leak Hazard. Regularly inspect dispenser and plumbing fittings for leaks, which can cause property damage and could result in personal injury.

* NOTICE: Property Damage. To reduce the risk associated with property damage due to water leakage or flooding, and to ensure optimal performance:

• Read and follow all instructions before installation and use of this system.
• Installation and use MUST comply with all state and local plumbing codes.
• Change the disposable filter cartridge; the disposable filter cartridge MUST be replaced every 6 months or sooner.

WHAT YOU NEED TO GET STARTED

Equipment Required:

• Drill
• Tape measure
• Adjustable wrench
• Level
• Phillips screwdriver
• Angle Stop Valve
• Pencil

Equipment You May Need:

• Anchors for plasterboard
• Basin wrench
• Tubing cutter
• Hole saw
• Hole punch

If you are not installing a filtration system, you may need 1/4″ (6mm) tubing and a 1/4″ union Connector.

If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench and a 1/8″ (3 mm) plug or a 1/4″ (6 mm) cap (not supplied) for the faucet spray hose line.

If you need to cut a mounting hole in your stainless steel sink, you may need a 1-3/8″ -­ 1-1/2″ (3.5 cm ­ 3.8 cm) hole saw made for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a surface other than stainless steel.

OVERVIEW OF COMPLETE SETUP

K 1/4″ 3/8″ T Fitting to plumb into cold line (sold separately)

A. Instant Hot Water Dispenser
B. Tank Outlet Tube: soft, large diameter tube
C. Vent Tube: soft, small diameter tube attached to hard black plastic tube
D. Water Inlet Tube: hard, plastic clear ¼” tube
E. Water Outlet Tube: hard, white plastic tube with quick connect
F. Rubber Gasket (pre-installed in faucet)
G. Rubber Gasket
H. Metal Washer
I. Locking Nut
J. Hot Water Tank

SOLD SEPARATELY

K. T Fitting or Angle Stop Valve
L. Filter Head and Cartridge
M. 3/4in (19mm) screws (4)
N. Y-Connector
O. Filter Tubes (2)

F1000S or F2000S (sold separately)

IMPORTANT INSTALLATION INFORMATION

* Notice: Property Damage: Before installing this system be aware of the following requirements to avoid water leakage which could cause property damage. After completing installation check the system to ensure these requirements are complied with.

QUICK CONNECTIONS

Ensure that the tubes are straight near the quick connections.

Ensure that the tube is pushed all the way into the quick connection.

Regularly inspect all quick connections for leaks. Turn off the water supply immediately if a leak is detected or the connector appears damaged. Replace the quick connector before turning the water back on. If cleaning any of the connection or tubing, use only water.

PLASTIC TUBING

1/4″ Outer Diameter Tubing:
Minimum bend radius (R) is 1″ (25.4 mm)

3/8 Outer Diameter Tubing:
Minimum bend radius (R) is 1.25″ (31.8 mm)

Ensure the plastic tube with the quick connection that is attached to the hot water tank is straight for 1″ (25.4 mm) above the connection.

Turn off the water supply line

Required minimum distance from center of hole to wall
1-1/8″ (29 mm)

Required hole size
1-3/8″ (35mm) — 1-1/2″ (38mm)

Note: If you have to drill through sink or countertop, you may need to rent or purchase the appropriate tools. Maximum counter thickness is 2-9/16″ (65mm).

Note: Hand tighten locking nut (I). Install step may require 2 people.

* NOTICE: Property Damage. Do not pinch or break the tubes).

* NOTICE: Property Damage. Do not plug in hot water tank until installation is complete. Tank must be located within 16″ (400 mm) of instant hot water dispenser and within 30″ (760 mm) or less of a standard earth (grounded) outlet. DO NOT extend plumbing or electrical lines. Note: An accessible location for maintenance inspection and tank replacement.

WARNING: Personal Injury/Property Damage. To reduce the risk associated with hazardous voltage due to an installer drilling through existing electric wiring in the area of installation: Do not install near electric wiring or water pipes which may be in path of a drilling tool when selecting the position to mount the system bracket.

* NOTICE: Property Damage. Pinched or blocked water lines may cause damage to the water tank. Check to make sure tubes are connected correctly and are pushed down as far as possible. Hose clamps not needed. Do not allow water to collect in tube B. Shorten as needed to make sure all water drains down and into the tank.

NO FILTRATION SYSTEM SKIP TO STEP 14.

WARNING. (Personal Injury) Do not locate filter above an outlet or other electrical device. Install head and bracket so that connections require no stretching, kinking or pinching of tubing.

* NOTICE: Property Damage. Top surface of cartridge will be flush with bottom of filter head when fully engaged.

WITH FILTER SYSTEM

WITHOUT FILTER SYSTEM

*NOTICE: Property Damage. Tube runs need to form to the cabinet’s contours to allow storage space with no sharp bends. Tubes need clean, perpendicular, burr-free cuts to ensure a true fit.

1. From water supply
2. To faucet
3. **Not included

Note: Check all connections to ensure they are tight and that there are no leaks. To fill tank, activate handle until water is flowing. Allow water to run for 3 minutes to flush lines.

1. Activate hot handle

*NOTICE: Property Damage. Do not use an extension lead with the instant hot water dispenser. (A standard earthed GFCI outlet within 30″ (760 mm) of the instant hot water dispenser is required under the sink.)

1. Factory temperature pre-set approx. 200 F

Allow 16-20 minutes for water to reach target temperature. Gurgling or hissing is normal during the initial heating cycle.

CAUTION: Scalding Hazard. The instant hot water dispenser delivers near- boiling (up to 210ºF/98ºC) water which can instantly cause scalds or burns. Use care when operating this appliance.

3-YEAR IN-HOME FULL SERVICE LIMITED WARRANTY

This limited warranty is provided by InSinkErator, a business unit of Insinkerator LLC, (“ InSinkErator ” or “ Manufacturer ” or “ we ” or “ our ” or “ us “) to the original consumer owner of the InSinkErator product with which this limited warranty is provided (the “ InSinkErator Product “), and any subsequent owner of the residence in which the InSinkErator Product was originally installed (“ Customer ” or “ you ” or “ your “).

InSinkErator warrants to Customer that your InSinkErator Product will be free from defects in materials and workmanship, subject to the exclusions described below, for the “ Warranty Period “, commencing on the later of: (a) the date your InSinkErator Product is originally installed, (b) the date of purchase, or (c) the date of manufacture as identified by your InSinkErator Product serial number. You will be required to show written documentation supporting (a) or (b). If you are unable to provide documentation supporting either (a) or (b), the Warranty Period commencement date will be determined by Manufacturer, in its sole and absolute discretion, based upon your InSinkErator Product serial number.

Permitted Uses
You may use your InSinkErator Product hot/cold water tank and filter system in combination with any genuine InSinkErator Product instant hot water dispensers and component parts and/ or Authorized OEM Products. “Authorized OEM Products” mean those hot, cold or hot/cold water dispensers and component parts that have been manufactured by an authorized InSinkErator original equipment manufacturer (“Authorized OEM”) and which have documentation expressly stating that such Authorized OEM Products are compatible with the InSinkErator Product(s). Authorized OEMs may change from time to time. A list of Authorized OEMs is available to you upon request or at: www. insinkerator.com/oem. Use of your InSinkErator Product in combination with any products other than Authorized OEM Products will void this warranty.

What is Covered
This limited warranty covers defects in materials or workmanship, subject to the exclusions below, in InSinkErator Products used by a consumer for residential use only, and includes all replacement parts and labor costs. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE INSINKERATOR PRODUCT, PROVIDED THAT IF WE DETERMINE IN OUR SOLE DISCRETION THAT NEITHER REMEDY IS PRACTICABLE, WE MAY PROVIDE YOU A REFUND OF YOUR PURCHASE PRICE OR A CREDIT TOWARDS ANOTHER INSINKERATOR PRODUCT.

What is not Covered
This limited warranty does not extend to and expressly excludes:

• Losses or damages or the inability to operate your InSinkErator Product resulting from conditions beyond the Manufacturer’s control including, without limitation, accident, alteration, misuse, abuse, neglect, negligence (other than Manufacturer’s), failure to install, maintain, assemble, or mount the InSinkErator Product in accordance with Manufacturer’s instructions or local electrical and plumbing codes.
• Wear and tear expected to occur during the normal course of use, including without limitation, cosmetic rust, scratches, dents or comparable and reasonably expected losses or damages.
• Losses or damages caused by any product or component part used with the InSinkErator Products, including both Authorized OEM Products and other products and components.

In addition to the above exclusions, this warranty does not apply to InSinkErator Products installed in a commercial or industrial application.

No Other Express Warranty Applies
This limited warranty is the sole and exclusive warranty provided to the Customer identified above. No other express warranty, written or verbal, applies. No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any other warranty on behalf of Manufacturer. The terms of this limited warranty shall not be modified by the Manufacturer, the original owner, or their respective successors or assigns.

What we will do to Correct Problems
If your InSinkErator Product does not operate in accordance with the documentation provided to you, or you have questions concerning your InSinkErator Product or how to determine when service is needed, please call the toll free InSinkErator AnswerLine® at 1 800-558-5700, or visit our website at www.insinkerator.com. You may also notify us at: InSinkErator Service Center, 1250 International Drive, Mount Pleasant, WI 53177 USA.

The following information must be provided as part of your warranty claim: your name, address, phone number, your InSinkErator Product model and serial number, and if necessary, upon request, written confirmation of either: (a) the date shown on your installation receipt, or (b) the date shown on your purchase receipt.

Manufacturer or its authorized service representative will determine, in its sole and absolute discretion, if your InSinkErator Product is covered under this warranty. You will be given the contact information for your closest authorized InSinkErator Service Center. Please contact your InSinkErator Service Center directly to receive in home warranty repair or replacement service. Only an authorized InSinkErator service representative may provide warranty service. InSinkErator is not responsible for warranty claims arising from work performed on your InSinkErator Product by anyone other than an authorized InSinkErator service representative.

If a covered claim is made during the Warranty Period, Manufacturer will, through its authorized service representative, either repair or replace your InSinkErator Product. Cost of replacement parts or a new InSinkErator Product, and cost of labor for repair or installation of the replacement InSinkErator Product are provided at no cost to you. Repair or replacement shall be determined by Manufacturer or its authorized service representative in their sole discretion. All repair and replacement services will be provided to you at your home. If Manufacturer determines that your InSinkErator Product must be replaced rather than repaired, the warranty on the replacement InSinkErator Product will be limited to the unexpired term remaining in the original Warranty Period.

This instant hot water dispenser is covered by Manufacturer’s limited warranty. This limited warranty is void if you attempt to repair the InSinkErator Product. For service information, please visit www. insinkerator.com or call, toll free, 1-800-558-5700.

Limitation of Liability
TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL MANUFACTURER OR ITS AUTHORIZED SERVICE REPRESENTATIVES BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE INSINKERATOR PRODUCT OR THE MANUFACTURER’S OR ITS AUTHORIZED SERVICE REPRESENTATIVE’S NEGLIGENCE. MANUFACTURER SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL MANUFACTURER’S LIABILITY TO YOU EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE INSINKERATOR PRODUCT.

The term “consequential damages” shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or damage to property or equipment.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state.

INSTANT HOT WATER DISPENSER TROUBLESHOOTING

Water and steam spits forcefully from spout without activating the instant hot water dispenser.| Unit is boiling. May be normal during initial set-up| • Activate instant hot water dispenser to release some water from the tank.
• Adjust water temperature using dial on tank front.
• Remember that at higher altitudes, water boils at lower temperatures.
• Water has pooled in tank outlet tube. Shorten tube to ensure drainage into tank. See Step 8.
Water is not hot.| • The unit is unplugged.
• The electric outlet is inoperative.| • Make sure the unit is connected to a correctly earthed GFCI electric outlet.
• Make sure the circuit breaker or fuses are functioning correctly.
• Check that the outlet is not switched off.
Water is too hot or not hot enough. | • Thermostat is not adjusted to your needs.| • Adjust the thermostat slowly, then activate instant hot water dispenser for 20 seconds to bring in fresh water to be heated at the new setting. Allow 5-7 minutes for water to reach new temperature.
Water comes out of the vent instead of spout.| • Outlet tube is blocked.| • Check that outlet tube is not kinked, twisted or pinched.
• Unscrew spout end piece and clean out any debris.
Water is dripping from the spout/vent intermittently.| • The expansion chamber is not draining properly due to low water pressure.
• The spout is blocked.| • Unplug the unit. If the dripping does not stop after a few minutes, check the supply valve to ensure that it is fully open and there are no obstructions in the water line reducing the pressure below 15 psi.
• Unscrew spout end piece and clean out any debris.
Water is dripping from the spout/vent constantly.| • Debris in the water line may be in the instant hot water dispenser valve seat, causing a slow water leak. | • Unscrew spout end piece and clean out any debris. Activate instant hot water dispenser 7-10 times to flush dispenser and lines.
Black specs/ water discoloration/ rusty appearance| • Incorrect installation of filter or corrosion from water line or tank| • Black specs may be due to the carbon block filter. If you have a filter, first flush out the filter by running water. Also, check to make sure the water supply is connected to the inlet of the filter head. For water discoloration, unplug and drain unit. If the water discoloration remains after draining and refilling the unit, discontinue use and contact Customer Care at 800-558-5700.
Divided stream.| • Debris in the end piece.| • Unscrew spout end piece and clean out any debris.

MAINTENANCE

NOTICE

• Regularly inspect the unit for any signs of leakage. If there are signs of water damage, immediately remove the unit from service.
• A drainage pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage

ADJUSTING THE THERMOSTAT
Adjust the dial on the front of the tank clockwise to raise the temperature or counterclockwise to lower the temperature.

SEASONAL STORAGE/DRAINAGE

• Anytime the unit is not used for extended periods of time, unplug and drain unit. If it is below freezing you will need to unplug the unit and drain it.
• Disconnect power from unit (unplug unit).
• Activate hot water faucet handle and allow water to flow until it is cool.
• Shut the cold water dispenser off at the valve.
• Disconnect tubes from the tank.
• Unhook tank from wall.
• Hold tank upside down and drain the water into the sink.
• Towel dry any water drippings from the tank area.
• Reinstall tank to wall and reconnect tubes.
• Remove and discard filter cartridge (if applicable).
• To put back into working order, install new filter cartridge (if applicable) and turn on cold water supply at valve. Activate hot water faucet handle and hold until water flows from the spout. Plug in the tank.

CLEANING THE INSTANT HOT WATER SYSTEM

• Use only mild cleaners to clean the instant hot water dispenser and plastic components.
• To clean out end piece, unscrew spout end piece and clean out any debris.
• Cleaners with acids, abrasives, alkaline or organic solvents will result in deterioration of the plastic components and void the warranty.

CARE AND USE

CAUTION: Electric Shock Hazard. To prevent electrical shock, disconnect power before servicing unit. Use only a properly earthed and polarized GFCI electric outlet.

WARNING: Scalding Hazard. Do not allow water to boil. May result in severe burns.

CAUTION: PERSONAL INJURY
Regularly check for signs of corrosion by examining the appearance of the dispensed water every three (3) months. If there is any discoloration or rusty appearance, unplug and drain unit as described in the Seasonal Storage/Drainage section on this page in the manual. If the water discoloration remains after draining and refilling the unit, discontinue use and contact an authorized InSinkErator service agent.

InSinkErator
Mount Pleasant, WI 53177
USA
Sales/Service Tel: 800-558-5700
www.insinkerator.com

InSinkErator Canada
66 Leek Crescent
Richmond Hill, ON L4B 1H1
Canada
Sales/Service Tel: 1-800-561-1700
www.insinkerator.ca

          NSF/ANSI/CAN 61:Q < 1

  1-800-558-5700 262-233-2231

45641-ISE REV A

InSinkErator may make improvements and/or changes in the specifications at any time, in its sole discretion, without notice or obligation and further reserves the right to change or discontinue models.
®/TM © 2022 InSinkErator. All rights reserved.

References

• Garbage Disposals | Instant Hot Water Dispensers | InSinkErator US
• insinkerator.com/oem
• Leader in Garburators and Hot Water | InSinkErator CA
• Garbage Disposals | Instant Hot Water Dispensers | InSinkErator US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>