Newbealer NB602N Steam Mop and Cleaner User Guide

Newbealer NB602N Steam Mop and Cleaner

USER MANUAL
Please read the User Manual carefully before use and keep it in a safe place for future reference.

SAFETY INSTRUCTIONS

WARNING! Please read and understand all safety precautions and operating instructions before operating this appliance. Improper usage of the product can result in damage to the product or serious injury to the user.

• Always unplug ASAP after each use to turn off the unit.
• Please use the correct supply voltage: 120V/60Hz. Do not share the same power supply with other high-power appliances
• Never touch any of the attachments while the steam cleaner is in use as they will be very hot and could burn skin.
• Do not allow steam to be sprayed onto devices that contain electrical components
• Never point the steam cleaner at yourself, other people, or pets.
• Never use the device without water in the tank.
• The mop pad must be placed on the bottom of the mop head before use. The mop pad can be used to wipe the floor and also protect the floor.
• Do not open the water tank while the device is in use. You should long press the power switch to close the steam, unplug the plug, and then add water to the water tank.
• Make sure the tank cap is securely closed before powering on the device to avoid a leak.
• Do not overfill the water tank. The maximum capacity is 8.5 fl. oz. (250 ml) of water. Excessive filling of the water tank may cause malfunctions, property damage, or injury.
• Do not use any cleaners or chemicals in the water tank.
• Make sure the attachment you want to use is securely connected before powering on the device.
• Do not submerge the device or power cord in water or any other liquid.
• Do not place the power cord close to the surface of a hot object to avoid damage.
• If the power cord is damaged, it must be confirmed by a designated service center staff member or an equivalent electrician.
• Do not attempt to disassemble or repair this device. There are no user-serviceable parts.
• Keep the device and its power cord out of reach of children. Cleaning and maintenance should not be done by children or people unfamiliar with the device.
• Do not leave this device unattended when connected to power.
• This device will remain hot after unplugging it. Allow the device to cool down before handling.
• Always disconnect the device when not in use,left unattended, after use, and before servicing. Stop all controls before unplugging.
• Only use the original accessories included in the box.Using incompatible accessories may result in a safety risk to the user.
• Washable Microfiber Pads and 7 Brushes-acces­sories are suggest to be replaced each 3-6 months.

SPECIFICATIONS

Model No.| Rated Voltage| Rated power| Rated Frequency| Tank Capacity| Continuous working time
---|---|---|---|---|---

NB602N

| ****

120V

| ****

1200W

| ****

60Hz

| 8.4502/

250ml

| ****

10-25min

PRODUCT DETAILS

Parts Identification

1. Water tank
2. Steam switch button
3. Steam level indicators
4. Main unit body
5. Connect button
6. Extension rod
7. Connect button
8. Mop head
9. Triangle brush
10. Nylon brush x2
11. Brass brush
12. Gap brush
13. Measuring cup
14. Steam Jet Nozzle
15. Squeegee
16. Microfiber pads x2
17. Carpet Glider

SELECTING ATTACHMENTS

• Steam Jet Nozzle – Focuses the flow of steam from the main nozzle. Attach to the main nozzle and use it to connect the squeegee, mop head, or any of the brushes.

• Squeegee – Connects directly to the steam jet nozzle. Use the squeegee to clean glass and windows.

• Nylon Brush – Connects directly to the steam jet nozzle. Use the nylon brush when extra scrubbing is required.

• Brass Brush – Connects directly to the steam jet nozzle. Use the brass utility brush to remove tough stuck-on grease and grime from durable surfaces.
  NOTE : Scratchable surfaces like stainless steel may be scratched or damaged by the brass bristles. Use care in deciding when to use the brass utility brush. If you are unsure about using this brush, it is recommended that you test a small, inconspicuous spot before proceeding.

• Mop Pads – The reusable microfiber pads are perfect for deep cleaning these hard floor surfaces:

  • Sealed Hardwood
  • Stained Concrete
  • Sealed Laminate
  • Linoleum
  • Glazed Ceramic
  • Granite
  • Marble
  • Vinyl
  • Tile

• Carpet Glider – Suitable for cleaning carpets.

BEFORE USE

Filling the Water Tank

1. Hold the body of the steamer upright and open the top of the water tank.
2. Ensure that the power light is off and the power cord is unplugged.
3. Carefully unscrew and remove the water tank cap.
4. Using the included measuring cup, slowly fill the water tank taking care not to overfill the tank (refer to Figure 2).

The maximum water capacity of this device is 8.5 fl. oz. (250 ml).

5. Close the water tank securely before using the steam cleaner.
   NOTE : The water tank should be emptied after each use to prevent mineral build-up and overfilling.

Installation and use of accessories

1. Steam Jet Nozzle
   To use the squeegee or brushes, begin by connecting the steam jet nozzle to the main nozzle.

2. Align the jet nozzle with the main nozzle.

3. Hold down the connection button and slide the jet nozzle onto the main nozzle. Rotate the main nozzle slightly until the connection button closes. (refer Figure 3)

4. Attaching Squeegee or Brushes
   To connect the squeegee or brushes to the steam jet nozzle, follow the steps below: (refer Figure 4)

5. Align your selected attachment with the steam jet nozzle tip. Makesure the grooves on the attachment line up with those on the steam jet nozzle.

6. Firmly press the attachment onto the steam jet nozzle. Press the attachment onto the nozzle as far as possible to prevent steam leakage.

7. To remove the attachment, firmly grasp it and pull it off the steam jet nozzle.

8. Install Extension rods
   To use the steam mop or want to clean high, far places, begin by connecting the 2 extension rods to the machine.

9. Mop Head:

10. Align the mop head with the end of the extension rod.

11. Hold down the connection button and slide the mop head onto the extension rod until the lock button snaps closed.(refer Figure 5)

12. Microfiber Pads

13. Lay the microfiber pad on a flat surface with the two fastener strips facing upward.

14. Align the mop head above the microfiber pad.Make sure the mop head is oriented with the pad as Figure 6 shown.

15. Fastener strips will adhere to the pad grips on the bottom of the mop head. (refer Figure 6)

16. Carpet Glider

17. Set the carpet glider on the carpet with the smooth side down.

18. Place the mop head, with the cleaning pad attached, on top of the carpet glider.

OPERATION INSTRUCTIONS

1. With the water tank filled and the selected attachment connected, plug the power cord into an appropriate electrical outlet. As the device begins to heat up, the steam indicator lights will begin to light up.

2. After about 15 seconds, the middle level lights will remain on. Press the steam button to begin to use the steamer. To stop the flow of steam, hold the steam button for two to three (2-3) seconds. To power off the steam cleaner, unplug the power cord.

3. Use the steam switch button to change your desired steam level. High steam (Deep cleaning heavy traffic areas), Medium steam (regular cleaning), Low steam (delicate floors).

4. Minimum level: One light

5. Middle level: Two lights

6. Maximum level: Three lights

7. As steam cleaner: With the correct attachment on and the water tank full, plug in the device and allow it to heat up. For steam cleaning, the steam jet nozzle is recommended. Press the steam button to begin the flow of steam.
   NOTE : For the most effective cleaning, the maximum steam level is recommended.
   As steam mop: With the mop head attachment on and the water tank full, plug in the device and allow it to heat up. Press the steam button to begin mopping.
   NOTE : For mop cleaning, the medium steam level is recommended.

8. Once complete, hold the steam button for two to three (2-3) seconds to stop the flow of steam.
   NOTE :The steamer will remain hot after unplugging it. Allow the device to cool down before handling.

WARNING Do not aim the steam at pets, plants or any other electrical appliances during use to avoid burns or damage to the machine.

Water shortage

Please pay attention to the amount of water in the tank when you use it. When there is no water in the tank or the water is rarely enough to allow the pump to absorb water, please refer to the step to add water.
It is strictly forbidden to let the water tank of the machaine work without water at any time, which will cause damage to the machine.

MAINTENANCE

After Use

1. Simply press and hold the steam button to turn off the steam. Unplug the cord from the outlet and place the Steam Mop into the upright position. Let it cool for 10-15 minutes.
2. Carefully remove all accessories from the device.
3. Remove Carpet Glider
4. Place your feet on the edge of the carpet stand and gently lift the main unit to remove the carpet glider.
5. Remove the Mop Pad
6. Step on the edge of the cleaning pad and gently lift the steam mop to remove the used mop pad.
7. Empty the water tank by holding the unit beside a sink. Open the lid of the water tank and lean the unit over the sink to allow the water to drain out. Once the tank is empty, close the lid securely.
   NOTE : The water tank should be emptied after each use to prevent mineral build-up and overfilling.

Cleaning

1. Make sure to regularly clean the surface of the unit body by wiping it with a soft, dry cloth to remove any dust.
   Do not immerse the steam mop in water or other liquids.

2. Wash pad in warm water, separately from other cloths. Use only liquid detergents. Do not use fabric softeners or bleach. For best results, air dry.

NOTE:

• NEVER leave the Steam Mop with a damp/wet Dirt Grip pad on any floor for an extended period.
• When replacing the mop pad, make sure the machine is powered off and no steam is being ejected.
• Be careful not to touch the steam mop outlet with your hands to avoid burns.
• The mop pad can be reused after cleaning. Keep your home clean by replacing the mop pad every 2-3 months, depending on your usage.

WARNING Before replacing any accessories, be sure to unplug the (.D unit and give it sufficient time to cool down. Failure to do so may result in burns or other injuries

What Water to Use?
It is recommended to use de-mineralized or distilled water. If you fill your steamer with tap water, you may experience mineral build-up due to the high mineral content in the water supply in many cities. Mineral residue inside your steamer’s internal heater may cause intermittent steaming or, in severe cases no steaming at all. To avoid the problem, only use de-mineralized or distilled water in your steamer.
Anti-calc operation can be done if you notice your appliance performance has decreased. Fill the tank with white vinegar  50% with purified water 50%, and clean with high-level steam cleaning.

TROUBLESHOOTING

If your device is not operating properly, please check if it is related to any of the following problems or conditions. If you are still unable to detect and solve the problem, please contact the after-sales service for help.

Problems

| ****

Possible Causes

| ****

Probable Solutions

---|---|---

The steam mop does not heat up.

| The steam mop is not plugged in.| ****

Plug the power cord into an outlet.

Power is not flowing to the outlet.

| Check your circuit breaker or replace the fuse as needed. For additional help, contact a qualified electrician.

The steam cleaner does not create steam.

| ****

The steam mop is heating up.

| If the 3 lights below the Steam Control Button begin a cycling glow, wait 20s for the unit to warm up.

The water tank is empty.

| Fill the water tank to the appropriate level, fully immersing the ball in the water tank.

The steam mop is in standby mode.

| If the lights below the Steam Control Button are blinking, press the Steam Control Button to select a Steam setting.
There is an excessive amount of water in the steam.| ****

There is water condensation in the steam hose.

| ****

Point the nozzle towards a sink or tub and shake while pressing the steam button. Continue until excess water is drained.

There are many water stains on the floor.| ****

The mop pad is overwet.

| ****

We recommend you unplug the steam mop and change the microfiber cleaning pad.

Floors are cloudy, streaky or spotty after steaming.

| ****

The mop cleaning pad may be too dirty.

| ****

Disconnect the power supply and replace the mop pad. If the area to be cleaned is matted with thick oily dirt and stains, please sweep or vacuum your floors with detergent prior to cleaning with your steam mop.

The water tank is leaking.| The lid of water tank isn’t closed properly.|

Close the lid of tank securely.

LIMITED ONE-YEAR WARRANTY

Thank you for your purchase!

WARRANTY:
Enjoy a warranty for the steam mop for one year.
REPLACEMENT POLICY:
Free replacements are based on manufacturing defects but not replaced for the reason of abusing, misusing, or other non-intended usage of the steam mop. Based on the specific situation of the sample back, we reserve the right for maintenance or replacement.
EXCELLENT CUSTOMER SERVICE:
If you experience any issues with this product, please contact us, Newbealer is happy to be of service all the time. Any suggestions are also welcome.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>