kogan KAWLM55CNRA Tilt Extendable Full Motion Corner Wall Mount User Guide
- October 30, 2023
- Kogan
Table of Contents
USER GUIDE
TILT EXTENDABLE FULL MOTION
CORNER WALL MOUNT
(23″ – 55″)
KAWLM55CNRA
SAFETY & WARNINGS
CAUTION:
Rated weight is 45kg (99 lbs).
Use with products heavier than the rated weights indicated may result in
instability causing possible injury.
-
Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
-
Safety gear and quality tools must be used.
-
This product is suitable for installation on solid concrete walls, masonry walls or wood stud walls.
-
Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
-
Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
-
Do not allow children to play near this stand.
-
This product contains small items that could be a choking hazard if swallowed.
Keep these items away from children. -
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
-
A minimum of two people are recommended for this installation. Failure to use safety gear and safe working methods may result in property damage, serious injury or death.
IMPORTANT : Ensure that you have received all parts according to the
component checklist prior to installation. If any parts are missing or faulty,
contact your place of purchase for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular
intervals (at least every three months).
Suitable for TVs 23” – 55” maximum
VESA compatibility:
200×100, 200×200, 300×200, 300×300, 400×200, 400×300, 400×400
COMPONENTS
Wall mount assembly:
ASSEMBLY
Additional Tools Required (Not Supplied):
Step 1: Drywall, plaster or timber walls (with studs)
Use a stud finder to locate safe and suitable locations to install into wall.
Use a spirit level to double check the correct angle of the mount and mark the
intended hole positions with a pencil. Drill holes in the desired locations
(55mm deep, 4.5mm wide).
With the wall mount held in place, insert the washers and screws (W-C, W-A), tightening with a socket wrench. When installing on a drywall, plaster or timber wall, do not use the screw anchors (W-B).
Step 1: Concrete and masonry walls
Use a spirit level to double check the correct angle of the mount and mark the
intended hole positions with a pencil. Drill holes in the desired locations
(60mm deep, 10mm wide).
Insert the screw anchors (W-B) into each pre-drilled hole. With the wall mount
held in place, insert the washers and screws (W-C, W-A), tightening with a
socket wrench.
For all wall types:
A minimum of two people are recommended for this installation.
Failure to use safety gear and safe working methods may result in property
damage, serious injury, or death.
Ensure washers and screws are aligned in the centre of opening. Do not install
with washers and screws off to either side.
Step 2 : Preparing the VESA mount plate
Ensure the two top nuts (E) are not fully tightened, leaving a gap of 4mm.
Configuration for VESA 300×300, 400×400:
300×200, 400×200:
400×300:
Step 3: Attaching the mounting brackets to your TV.
Depending on your TV, a combination of spacers (M-H, M-I) may be required to
help create the correct amount of space for the brackets. Ensure the screws
are fitted correctly into your TV’s VESA mount holes, and are not too long or
too short in the back of the TV.
Step 4 : Attaching the TV to the wall mount.
With two people, lift the TV up and into position on the mount, ensuring the
4mm gaps on the mount plate nuts slide into the two openings on the mount.
The lower bolt of the mount plate should feed through the opening at the
bottom of the mount. Secure this with a nut (E), while tightening the two top
nuts.
A minimum of two people are recommended for this installation.
Failure to use safety gear and safe working methods may result in property
damage, serious injury, or death.
Step 5: Use the supplied cable management clips to secure all of the TV’s
power and connection cables, as shown below.
ADJUSTING
Adjusting level angle: Loosen the nuts on the back of the mount (as shown below) to balance the TV’s level. When done, ensure nuts are securely tightened.
Adjusting tilt angle : Loosen the nuts on the side of the mount (as shown below) to adjust the TV’s tilt angle. When done, ensure nuts are securely tightened.
NOTES
Need more information?
We hope that this user guide has given you the assistance needed for a simple
set-up.
For the most up-to-date guide for your product, as well as any additional
assistance you may require,
head online to help.kogan.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>