Kogan KAMN32F7SA 32 Inch Full Hd Ips 75hz Freesync Monitor User Guide
- October 30, 2023
- Kogan
Table of Contents
KAMN32F7SA 32 Inch Full Hd Ips 75hz Freesync Monitor
User Guide
SAFETY & WARNINGS
Ensure to read all instructions and warnings in this user guide prior to assembly and use. Retain this user guide for future reference.
- Ensure the monitor is unplugged before cleaning.
- This monitor is designed with ventilation holes on the back of the casing. Do not cover or block them.
- Do not insert any object or spray anything into the vents.
- Do not place the monitor near heaters, stoves, fireplaces, or other heat sources.
- Do not place the monitor in rooms lacking adequate ventilation.
- Do not position the monitor on unstable surfaces or unsafe locations. If the monitor falls, it may be damaged and injure people around its vicinity.
- Unplug the monitor if it will not be used for an extended period.
- Do not place heavy objects on the monitor, its power cord, or any connected cable.
- Do not open the back panel of the monitor as it contains a high-voltage current even when not plugged in.
The terms HDMI and HDMI High-Definition Multimedia Interface and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
COMPONENTS
OVERVIEW
Front view
| 1 Menu button | Press to display the OSD menu or enter sub-menus. |
|---|---|
| 2 Down button | Press to move down in the menu. |
| 3 Up button | Press to move up in the menu. |
| 4 Exit button | Press to exit. |
| 5 Power button | Press to turn the monitor ON/OFF. |
Back view
| 6 | Audio output port |
|---|---|
| 7 | VGA port |
| 8 | HDMI port |
| 9 | Power port |
STAND ASSEMBLY
Attention:
The monitor is fragile. Keep the foam underneath the monitor while assembling
the stand.
- Open the packaging and remove the stand connector (B) and stand base (C). Using a Phillips head screwdriver (not supplied), secure the stand connector (B) to the stand base (C) with two 10mm M4 stand base screws (D).
- Remove the upper foam and reveal the lower part of the monitor (A). Fix the monitor (A) to the stand connector (B) with three 10mm M4 stand base screws (D) in the marked grey holes as illustrated.
- Place the cover (F) over the stand connector (B).
VESA MOUNT
-
Open the packaging and take out the monitor (A) with the foam attached. Gently place it on a desktop or table.
-
Remove the stand connector (B), stand base (C), and foam covering the back of the monitor (A). Press the release button to remove the stand plate.
If the monitor was already attached to the stand, remove the stand.
-
Mount the monitor (A) as desired with the steps provided with your VESA mount.
Notes:
- The mounting hole distance for this monitor is 75 x 75mm.
- VESA mount and mounting accessories are not included.
CONNECTIVITY
Power cable
Connect one end of the power cable into the power port on the monitor. Connect
the other end into a power socket. Earphones (audio out)
Earphones and other audio devices (not included) can be connected to the audio
output port on the monitor.
The monitor may need to be set as the PC’s default sound output device.
HDMI
Connect the HDMI cable into your input device’s display output and the
monitor’s HDMI port. VGA
Connect a VGA cable (not included) into your input device’s display output and
the monitor’s VGA port.
OPERATION
- Connect the monitor to the input device via HDMI or VGA.
- Connect one end of the power cable to the monitor, then connect the other end directly to a power socket. Turn on the power socket.
- Press the power button to turn the monitor on.
- When finished use, press the power button again to turn it off.
FreeSync
- To use this feature, ensure your hardware has FreeSync capabilities and the graphics drivers are fully up to date.
- After connecting, you may receive a prompt to enable the feature on your computer. If you do not receive the prompt, you may need to enable the function in your graphics card menu.
- See your graphics card manufacturer’s documentation for instructions on how to turn on and/or enable FreeSync.
On-screen display (OSD) menu
The OSD menu may be used to adjust the monitor’s settings. 
Note:
When using the monitor for the first time, the monitor will configure to
optimal settings automatically.
- Press the menu button to enter the OSD menu.
- Press up and down buttons to browse the settings categories. With the desired category highlighted, press the menu button to enter the sub-menu.
- Press the up and down buttons to browse the sub-menu. With the desired sub-menu setting highlighted, press the menu button to select the sub-menu setting.
- Press the up and down buttons to adjust the setting. Once adjusted, press the menu button to confirm.
- Press the exit button to return to the display.
OSD menu options
Below is a list of settings that can be adjusted in the OSD menu.
| Category | Sub-menu | Setting | Description |
|---|---|---|---|
| Brightness | Brightness | 0-100 | Adjusts the display brightness |
| Contrast | 0-100 | Adjusts the display contrast | |
| Backlight | 0-100 | Adjusts the display backlight | |
| Low blue | ON/OFF | Enables/disables the blue light reduction function | |
| ECO | STANDARD/ TEXT/GAME/ MOVIE/FPS/RTS | Sets the display’s colour balance to |
pre-set levels calibrated for different uses.
DCR| ON/OFF| Enables/disables the dynamic contrast ratio function
Image| Horizontal position| 0-100| Adjusts the horizontal position of the
video display area (VGA only)
Vertical position| 0-100| Adjusts the vertical position of the video display
area (VGA only)
Clock| 0-100| Adjusts the display dock setting
Phase| 0-100| Adjusts the display phase setting
Aspect| Wide (16:9), 4:3| Adjusts the aspect ratio
Resync| ON/OFF| Turns the Resync function on/off
Colour| Warm mode| Red/green/blue| Adjusts the red/green/blue levels
---|---|---|---
Cool mode| Red/green/blue| Adjusts the red/green/blue levels
User mode| Red/green/blue| Adjusts the red/green/blue levels
HDR mode| On/Off| Turns the HDR mode on/off.
OSD Setting| Language| English,| Sets the OSD language
OSD H-position| 0-100| Adjusts the horizontal position of the OSD menu
OSD V-position| 0-100| Adjusts the vertical position of the OSD menu
OSD transparency| 0-100| Adjusts the transparency of the OSD menu
OSD time out| 5-60| Sets how long the OSD menu will remain on-screen after no
input (seconds)
Reset| Image| N/A| Restores the display to VGA image defaults
Colour| N/A| Automatically configures the VGA colour settings
Reset| N/A| Restores the monitor to factory default settings
Time count| 10-90 mins| Adjusts how long the time count function should be set
for
Misc.| Signal source| VGA/HDMI| Adjusts the input source
ECO modes
There are various pre-set colour modes suited for various use cases available
on this monitor.
These can be accessed using the ECO modes menu. The modes include the
following:
- Standard (suitable for most activities)
- Text (best suited when reading text)
- Game (best suited for general gaming)
- Movie (best suited when watching movies)
- FPS (best suited when playing first-person shooter games)
- RTS (best suited when playing real-time strategy games)
GamePlus menu
To access the GamePlus menu, press the exit button, followed by the menu
button. The GamePlus menu allows users to access two settings:
- Crosshair – Allows users to change the appearance of the crosshair used when gaming)
- Timecount – Allows users to turn on a timer to record how long the monitor has been used (10–90mins).
CLEANING & CARE
- To clean the screen, turn it off, unplug it, and wait for it to cool completely. Wipe it with a dry micro-fibre cloth.
- To clean the body, wipe with a clean, slightly dampened cloth.
Note:
Do not use cleaning alcohol, ammonia-based liquids, or other harsh cleaners.
SPECIFICATIONS
| Screen size | 32” |
|---|---|
| Aspect ratio | 16:09 |
| Brightness | 300cd/m² (typical) |
| Panel | IPS |
| Resolution | 1920 x 1080 |
| Refresh rate | 75Hz |
| Response time | 8ms |
| Viewing angle | ≥178°(H)/178°(V) |
| Contrast ratio | 1000:01:00 |
| VESA mounting | 75 x 75mm |
| Colours | 16.7M |
| Signal input | HDMI 1.4 x1, VGA x1 |
| Power supported | 100–240V, 50/60Hz, 1.1A |
| Audio | |
| --- | --- |
| Speakers | No |
| Accessories | |
| Power cable | Yes |
| HDMI cable | Yes |
| Additional functions | |
| Low blue light | Yes |
| Flicker-free | Yes |
| Physical dimensions | |
| Dimensions (w. stand) | 720.5 x 84.6 x 507.0mm |
| Dimensions (without stand) | 720.5 x 42.9 x 423.1mm |
| Net weight | 6.3kg |
| Gross weight | 8.2kg |
Need more information?
We hope that this user guide has given you the assistance needed for a simple
set-up.
For the most up-to-date guide for your product, as well as any additional
assistance you may require, head online to help.kogan.com