Kogan com KADCFAN3N1A 3 In 1 Dc Motor Pedestal Fan User Guide

: October 30, 2023
: Kogan com

Table of Contents

SAFETY & WARNINGS
COMPONENTS
OVERVIEW
ASSEMBLY
BEFORE FIRST USE
OPERATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**Kogan com KADCFAN3N1A 3 In 1 Dc Motor Pedestal Fan User Guide

**

SAFETY & WARNINGS

Ensure to read this user guide prior to first use. Retain this user guide for future reference.

This fan can be used by children aged 8 years and above and by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the fan in a safe way and understand the hazards involved.
Adult supervision is required when the fan is operating around children.
Do not allow children to play with the fan.
Cleaning and maintenance shall not be performed by children without supervision.
Do not allow the fan and remote control to be operated in or around water or any other liquid.
Do not submerge the fan or remote into water or any other liquid.
Do not touch the blades when the fan is in operation.
Always disconnect the power cord before cleaning.
If the power cord is damaged, stop use immediately and contact help.Kogan.com for assistance.
Do not attempt to repair the fan yourself.
Once the fan is assembled, do not remove the grilles.

COMPONENTS

A Base (x1)
B Pole assembly (x2)
C Fan body (x1)
D Fan blade (x1)
E Front grille (x1)
F Rear grille (x1)
G Screw (x1)
H Remote control (x1)
I User guide (x1)

OVERVIEW

Fan

Control panel

Remote control

```
* 
```

ASSEMBLY

Loosen and remove the lock nuts for the rear grille and fan blade from the fan body.
Secure the pole assemblies to the base by rotating clockwise.
Attach the fan body onto the pole assembly, then attach the rear grille onto the fan body.
Secure the rear grille lock nut clockwise onto the rear grille. Secure the fan blade, then place and turn the fan blade lock nut anti-clockwise.
Align the top clip of the front grille with the rear grille, then press the front and rear grilles together.
Using a screwdriver (not supplied), secure the locking clip connected to the front grille with the provided screw. This will secure the front grille in place.

BEFORE FIRST USE

Batteries for the remote control

Slide the back cover off the remote control.
Noting the polarity markings ‘+/–’, insert two AAA batteries (not supplied) into the remote control. Slide the back cover on.

OPERATION

Powering on/off

Plug the power cord into a socket, then turn the socket on.
Press the Power button on the remote control or control panel to turn on the fan.
Press the button again to turn off the fan.

Note: To ensure adequate air circulation to the motor, keep vents at the rear of the motor free of dust.

Timer
The timer can be set to either turn the fan on or off after a specified period between 0.5–12 hours.

Setting the timer to turn on the fan
There are two methods. Applicable to both methods, ensure the fan is in standby when setting this timer.

• Using the control panel:

Press and hold the oscillation/timer button for two seconds.
Repeatedly press the oscillation/timer button to adjust how long you wish the timer to last. This will be reflected on the display (0.5–12). Once adjusted, do not touch the control panel. Wait for six seconds.
Press the fan speed button to adjust the speed at which the fan will operate when it turns on (1–12).
Once adjusted, do not touch the control panel. Wait for three seconds. The display will flash twice and beep to confirm the timer has been set.

Notes:

If you wish to reset the timer, press and hold the oscillation/timer button.
Pressing the Power button will cancel the timer and turn on the fan.

Using the remote control:

Press the timer button to enter the timer settings.
Repeatedly press the timer button to set the timer to the desired number of hours. Each press will increase the timer by one hour. This will be reflected on the display

Setting the timer to turn off the fan

There are two methods. Applicable to both methods, ensure the fan is turned on when setting this timer.

Using the control panel:

Press and hold the oscillation/timer button for two seconds.
Repeatedly press the oscillation/timer button to adjust how long you wish the timer to last. This will be reflected on the display (0.5–12).
Once adjusted, do not touch the control panel. Wait for six seconds. The display will flash twice and beep to confirm the timer has been set.

Notes:

To check how much time is left on the timer, press and hold the oscillation/timer button. The time left will be shown on the display. If you would like to adjust the timer, immediately press the oscillation/timer button and adjust accordingly.
If nothing is pressed for six seconds, the current timer will remain set

Using the remote control:

Press the timer button to enter the timer settings.
Repeatedly press the timer button to set the timer to the desired number of hours. Each press will increase the timer by one hour. This will be reflected on the display.

Oscillation

When the oscillation function is turned on, the fan will automatically rotate left and right. Press the oscillation button on the remote control or the oscillation/timer button on the control panel to start/stop oscillating.

Changing the fan speed

This fan features twelve fan speeds. Press the fan speed button on the remote control or control panel to change the fan speed. The selected fan speed will be reflected on the display (1-12). Press and hold the fan speed button to quickly cycle through the fan speeds.

Adjusting the angle and height of the fan

The angle/tilt of the fan can be changed manually. Ensure the fan is turned off and unplugged before adjusting accordingly.

Adjusting the height
The pole assemblies can be removed to create different heights for the fan. This results in three different configurations.

To change the configuration:

Remove the fan body.
Rotate the pole assembly/assemblies anti-clockwise then remove.
Resecure the fan body onto the remaining pole assembly/base.

CLEANING & CARE

Ensure the fan is turned off and unplugged before cleaning.

Wipe the exterior with a soft cloth dampened with a mild detergent.
Remove any soapy residue with a dry cloth.

Notes:

Do not disassemble the fan to remove dust.
Do not use any abrasive detergents or solvents during cleaning to avoid scratching or damaging the surface of the fan.
Do not use gasoline or thinner for cleaning.

Disposal

This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it.

Costumer Support

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com