kogan KAS8C4W1TBB 8 Channel 1080p 1tb Security System User Guide
- June 9, 2024
- Kogan
Table of Contents
kogan KAS8C4W1TBB 8 Channel 1080p 1tb Security System
OVERVIEW
NVR
- Wi-Fi Antenna Port
- WAN Port (video in)
- VGA Port
- HDMI Port
- USB Port
- Power Input (DC 12V 2A)
Camera
- Antenna
- Camera Mount
- Lens & Sensors
- Ethernet Port (RJ-45)
- Power Input (DC 12V 2A)
INSTALLATION
System Overview
Notes:
- Camera connection to NVR is wireless: the NVR connection to the router is wired.
- It is recommended to place the NVR in the centre of the monitoring area and to avoid obstacles between the cameras and NVR as much as possible.
Adding Camera
The supplied cameras are matched at the factory. Re-adding or adding an
additional camera can be done in the Video Management settings on the NVR
using either “auto add” (cameras will be detected automatically) or “match
code”.
Cameras’ antennas should be positioned parallel to the Wi-Fi signal
transmission and not angled directly at the router.
The cameras can also be set up with a wired network connection.
System Setup
The system is a standalone unit with an embedded Linux operating system in the NVR. To configure the operating system, connect a keyboard, mouse and monitor with HDMI or VGA input.
- Install antennas for cameras and NVR.
- Connect a monitor via HDMI or VGA.
- Connect the NVR to power (use the larger 12V 2A power adaptor).
- Connect the cameras to power (use the smaller 12V 1A power adaptors).
- The camera feed will display within a few seconds.
- Connect the included USB mouse to a USB port on the rear of the unit.
Hard Drive Replacement
OPERATION
Mouse Function
| Button | Action | Effect | Function |
|---|
Left
| Single click| Select| Option button, drop down menu, list, check box, radio button
Double click
| ****
Window zoom
| 1. Switch between single and multi- interface in preview
2. Add device
Drag
| ****
Set the area
| 1. Set motion detection area
2. Select electronic amplification area
Middle
| ****
Scroll
| ****
Change the content
| 1. Change contents of the drop-down box
2. In zoom preview, switch channel interface orderly
Right
| ****
Single click
| ****
Log out
| 1. Close interface
2. Show shortcut menu in main interface
FUNCTIONS
Right click to access the following options:
- Split screen: single/multiple camera live feed
- Video management: manage IP & NVR channels
- System setup: change system settings
- Video playback: play back recordings
- Video backup: back up recordings
- Colours adjust: adjust image settings
- PTZ control: adjust PTZ settings (on supported cameras)
- Manual record: change recording settings
- Volume: change audio settings (on supported cameras)
- Setup Wizard: step-by-step initial setup guide
- Fast network: change network settings
- Exit System: logout, reboot, close display output and shut down system
Recording Video
- Timed Recording: Right click System Setup > Record Setup > Record Plan. You can set a schedule to record. The default mode is 24/7.
- Manual Recording: Right click Manual Record. Individual channels can be enabled/disabled.
- Motion Recording: Right click System Setup > Record Setup > Record Plan. Deselect Time and select Motion; the camera will only record when it detects motion.
Playback
Right click Video Playback > Manual Search. You can search by channel and time
and click Playback to view recorded videos.
Backup
- Connect a USB drive to a USB port on the device.
- Right click Video Backup > Choose Backup Channel > Choose Video Mode > Setup Searching Time > Search. Choose the video file to back up.
- Supported drive size is up to 32GB and supported recording is up to 1 hour.
Login / Logout
- Right-click on the shortcut menu and click the user to log off.
- To set a logout automatically, you can set this in system > general settings. The system will automatically log off the system in 1 minute. Username and password will need to be re-entered when next using the system.
Restart & Shut Down
- To restart the machine during use, right-click the shortcut menu and select “exit system”: click to complete the restart.
- To shut the machine down, right-click the shortcut menu and select the shutdown option.
Local Viewing
With the PC and the NVR connected to the same Local Area Network (LAN),
- Find the IP address and port number of the NVR (through System Setup > Network Setup).
- Enter the IP address in the browser (e.g., http://192.1.17). If the default port number has changed from 80, enter the port number as well in the format (e.g., if the port number was changed to 100 e.g., http://192.1.1.100)
Remote Viewing
- Navigate to http://e-seenet.com in a browser.
- Input Device ID, username and password to log in.
Device ID is shown at the right bottom corner of the monitor. The status should show as “online”. The default username is admin and the default password is empty.
Mobile Access
- Download the IP PRO app from the App Store, Play Store or by scanning the QR code below.
- Add the NVE through the device ID, username and password.
Device ID is shown at the right bottom corner of the monitor. The status should show as “online”. The default username is admin and the default password is empty.
Live playback is supported within the app. Due to network conditions and connection speed, playback over LAN will be more reliable and consistent than playback from mobile data.
EXTENDING WIFI RANGE
A wireless network is inherently susceptible to range limitations and interference from obstacles, etc. To improve the reliability and stability of a Wi-Fi connection, refer to the following setup tips and configuration options.
Antenna Extension
Repeater Setup
In the repeater setup page, first set up and connect any IP Camera to the NVR.
This function increases the wireless transmission distance and extends the
total range of wireless kit.
- Right click and select Video Management > Repeater.
- Add repeater: as below, click the icon and a channel besides the currently one being copied from (channel 3 in this example).
- As below, IPC1 is connected to the NVR through IPC2 and IPC3. IPC2 is connected to NVR through IPC3. IPC3 is connected to NVR directly.
- Click Apply > Refresh to confirm the setup is successful.
Need more information?
We hope that this user guide has given you the assistance needed for a simple
set-up.
For the most up-to-date guide for your product, as well as any additional
assistance you may require, head online to
help.kogan.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>