Westinghouse 77885 LIGHTING 4 Speed Ceiling Fan and LED Light Wall Control Instructions

: June 9, 2024
: Westinghouse

Table of Contents

INSTRUCTION
SAFETY PRECAUTIONS:
MAKING THE ELECTRICAL CONNECTIONS:
TROUBLESHOOTING GUIDE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Westinghouse 77885 LIGHTING 4 Speed Ceiling Fan and LED Light Wall Control Instructions

INSTRUCTION

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER

SAFETY PRECAUTIONS:

WARNINGS:

To avoid fire, shock, and serious personal injury, follow all instructions carefully. Read and save these instructions for future reference.
Do not install or use this unit if any part is damaged or missing.
WARNING! To reduce the risk of fire or electric shock, do not use it with any additional solid state fan speed control device, or any additional variable speed control.

NOTICE:

This control is designed to operate only one ceiling fan and accessory light kit.
This wall control is rated for a maximum (ceiling fan only) of 1.0 motor amp at 120 volts, and total lamp wattage equaling 80 Watt maximum.
Make sure no bare wires are exposed outside of the connectors.
All wiring must conform to National and Local Electrical Codes. If you feel that you do not have enough electrical wiring knowledge or experience, have your fan control installed by a licensed electrician. Any electrical work not described in this manual should be performed by a licensed electrician.
Use of this control with some ceiling fans could result in fire, shock, and serious personal injury. Use this fan control only with capacitor speed controlled ceiling fans only

MAKING THE ELECTRICAL CONNECTIONS:

NOTE: Installation of this control requires that the three-conductor cable with ground wire be run between the control wall box and the ceiling fan outlet.

If your ceiling fan is equipped with variable speed and light ON/OFF pull chain switch controls, make sure to set the speed control at the highest speed and the light to the ON position before installing the wall control. This will avoid erratic speeds and possible damage to your ceiling fan.
Verify proper operation of the ceiling fan wall control before installation. Improper wiring can damage the control and will void the warranty.
Disconnect power to the ceiling fan at the main electric panel. Remove the fuse or switch the circuit breaker to the OFF position.
Remove the wallplate to expose the wiring and disconnect the existing switch. Install the control in a metal or plastic wall box.
Make electrical connections as follows:

Connect the black wire marked with “TO MOTOR L” from the wall control to the BLACK wire from the fan.
Connect the BLUE wire from the wall control to the RED or BLUE wire from the fan.
Connect the black wire marked with “AC IN L” from the wall control to the 120v AC HOT wire.
Use the wire connectors provided to secure the connections.
Connect the GREEN/Ground wire from wall control to the grounding wire from wall box.

NOTE: Refer to the diagram on the back of the wall control.

Secure the wall control to the wall box using the two 6-32” x 1-1/8” screws provided.
Press the wallplate onto the wall control with an appropriate force.
Restore power at main electrical panel.
Operate ceiling fan and light by pressing the fan speed / light buttons to desired speed / light level.

HOW TO OPERATE YOUR WALL CONTROL:

OPERATE WALL CONTROL

The remote buttons function as follows:

Fan speed:
= High speed
= Medium-high speed
= Medium Speed
= Low Speed
Button: Turn the fan off
Light On/Off – press and release light button.
Light Dimmer – continuously press the light
button to brighten the light
Light Dimmer – continuously press the light button to dim the light. Power off switch- Carefully take off the wallplate and pull out this switch for cutting off the AC power.
Note: This switch to designed to disconnect the power if theceiling fan is not used for a long time.

SET button (under the small wallplate): The SET button is recessed into the hole, use a hard, slender object, such as a needle, to insert into the SET hole. It is for setting suitable dimmer level.

When the light flickers after dimming, you can use this button to improve this as following: Turn on the fan light and dim light to a suitable level, then short-press the SET button, the light will turn off and back on, it means the new dimmer level is activated and memorized.
Press and hold the SET button for 3 seconds to clear the memorized dimmer level. The light will turn off and back on, it returns to the default dimmer level.

WARNING! HOOK UP “IN SERIES” ONLY! Do not connect to hot and neutral wire of electric circuit or switch will be damaged. Refer to diagram above

TROUBLESHOOTING GUIDE

PROBLEM: WALL CONTROL FAILS TO OPERATE Check:

Is there power to the control unit?
Is the control unit wired correctly?
Are the fan and light switches set on the highest position?

LIMITED WARRANTY
The Westinghouse universal ceiling fan/light wall control offers a limited warranty of one year from the date of purchase to the original owner against defects in material and workmanship. All spare parts are covered for ninety days only. This warranty is in lieu of all other warranties expressed or implied. Westinghouse will repair or replace this universal ceiling fan/light wall control if it is defective due to faulty materials or workmanship. This warranty does not cover service charges, defects resulting from accidents, damages caused through abuse or alterations or by affixing any attachment not provided with the product, improper installation or maintenance, failure of supporting devices not supplied as original mounting hardware, exposures to extremes of heat or humidity, incorrect voltage, surges in current, unauthorized repair, or failures caused by modifications of the product or the acts of third parties. See remote manual for proper installation. If this product fails for any reason covered by this warranty, please contact us at www.westinghouselighting.com/contact-us.