lionelo Henny 3-in 1 Baby Rocker Baby Swing and Baby Deck Chair User Manual

: June 9, 2024
: lionelo

Table of Contents

lionelo Henny 3-in-1 Baby Rocker Baby Swing and Baby Deck Chair
IMPORTANT INSTRUCTION
Folding
INSTALLATION
Control panel (fig. 15)
Cleaning and maintenance
Read User Manual Online (PDF format)
Download This Manual (PDF format)

lionelo Henny 3-in-1 Baby Rocker Baby Swing and Baby Deck Chair

lionelo Henny 3-in 1 Baby Rocker Baby Swing and Baby Deck Chair-
PRODUCT

IMPORTANT INSTRUCTION

IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

WARNING

Never leave the child unattended.
Do not use this product once your child can sit up unaided or weighs more than 9 kg.
This product is not intended for prolonged periods of sleeping. Never use this product on an elevated surface (e.g. a table). Always use the restraint system.
To avoid injury ensure that children are kept away when unfolding and folding this product.
Do not let children play with this product.
Do not move or lift this product with the baby inside it. When the product is connected to a music player, ensure that the volume of the music player is set to a low value.
This product does not replace a cot or a bed. Should your child need to sleep, then it should be placed in a suitable cot or bed. Do not use the product if any components are broken or missing.
Do not use accessories or replacement parts other than those approved by the manufacturer.

Folding

lionelo Henny 3-in 1 Baby Rocker Baby Swing and Baby Deck
Chair-8

INSTALLATION

Combine the seat tubes. Slide the tubes into the guides until they lock in place. The “click” sound indicates proper connection. Repeat the procedure with the other side (fig. 1 ).
Then, install the tube that supports the seat (seethe below picture). Insert the steel part of the tube (with the plate) into the bottom of the seat base and tighten it with screws. Use the screws with the following number: 2 – for outer holes; 1 – for inner holes (fig. 2).
Installing the caps: Insert the left and right cap into the base tube, as shown in the picture below. The cap holes must overlap with the holes in the tubes (fig. 3). Use screws number 3 to attach the feet.
Attach the bases of the swing chair with the connecting tubes. Slide the tubes into the guides until they lock in place. The “click” sound indicates proper connection (fig. 4).
Combine the connecting tubes with the swinging mechanism (paying attention to the marks on the tubes). Slide the tubes into the guides until they lock in place. The “click” sound indicates proper connection (fig. 5).
Combine the seat supporting tube with the swinging mechanism. Slide the tubes into the guides until they lock in place. The “click” sound indicates proper connection (fig. 6). Use screw number 3 to additionally secure the connection.
Put the canopy on the seat frame so that the holes in the canopy handle match the seat frame pin (fig. 7).
A child sitting in a seat must be secured with the safety harness (fig. 8). The length of the belts can be adjusted with the clasps (fig. 9).
The swing chair’s seat angle can be adjusted to three different positions. Press the adjustment button (behind the seat) and choose a desirable position (fig. 10, 11 ). The seat can also be flipped (fig. 12)
It is possible to fold the bases for storage purposes. Press the buttons at the bottom of the swinging mechanism and fold the bases (fig. 13).
There are two methods of powering the LO-Henny swing chair.
- with an included power supply (fig. 14);
- with 4 D+ R20 1.5V batteries.

WARNING

Do not charge non-rechargeable batteries.
Rechargeable batteries can only be charged by adults. Rechargeable batteries should be taken out of the device’s battery compartment before charging.
Do not plug in the power supply if the batteries are installed in the unit.
Do not mix used batteries with the new ones.
Do not mix different kinds of batteries.
Do not mix rechargeable and non-rechargeable batteries. Make sure the batteries are properly installed according to correct polarity(+-).
Remove exhausted batteries from the device.
Use the original power supply (included with the product) only.
Keep batteries and the power supply away from children. If you plan not to use the device for extended period of time, please remove the batteries and disconnect it from the power supply.
To replace the batteries in the product, remove the battery compartment cover and replace the batteries. Replace the cover.
Transformers used with the infant swing are to be regulatarly examined for damage to cord, plug, enclosure and other parts, and in the event or such damage, they shall not be used.