EPOMAKER EP87 87 Key Three Mode Hot Swappable Mechanical Keyboard User Manual
- June 9, 2024
- EPOMAKER
Table of Contents
QUICKSTAR TGUIDE
EPOMAKER EP87
EP87 87 Key Three Mode Hot Swappable Mechanical Keyboard
87-key three-mode hot-swappable mechanical keyboard
This Quick Guide is an introduction to the use and functionality of the
EPOMAKER EP87.
For in-depth guide of functionality of the customization software please refer
to the manual that you can find in the official epomaker
website at
https://epomaker.com/pages/software-—downloads
Should you require more assistance please email us at
support@epomaker.com
MAC MODES
FN+F1 | Brightness- |
---|---|
FN+F2 | Brightness+ |
FN+F3 | Screenshot |
FN+F4 | Task Manager |
FN+F5 | Mute Audio |
FN+F6 | Volume- |
FN+F7 | Volume+ |
FN+F8 | Previous Song |
FN+F9 | Pause/Play |
FN+F10 | Next Song |
FN+F11 | search |
FN+F12 | Home Page |
WIN MODES
FN+F1 | Brightness- |
---|---|
FN+F2 | Brightness+ |
FN+F3 | Task Manager |
FN+F4 | Resource manager |
FN+F5 | |
FN+F6 | Home Page |
FN+F7 | Previous Song |
FN+F8 | Play/Pause |
FN+F9 | Next Song |
FN+F10 | Mute Audio |
FN+F11 | Volume- |
FN+F12 | Volume+ |
QUICK FUNCTION
FN+A | Win Modes |
---|---|
FN+S | Mac Modes |
Fn+Space | Current Modes |
FN+WIN | Win Lock |
FN+ESC (Hold 3s) | Reset |
FN+1 | Bluetooth 1 |
FN+4 | 2.4G |
FN+2 | Bluetooth 2 |
FN+5 | Type-c |
FN+3 | Bluetooth 3 |
RGB LIGH TEFFECT CONTROL
Fn+Backspace | RGB Backlight On/Off |
---|---|
FN+Pause | Change RGB Backlight Effect Modes |
FN+Home | Change RGB Backlight Effect |
FN+PgUp | Change RGB Backlight Effect direction |
FN+↑ | Increase Brightness |
FN+↓ | Reduce Brightness |
FN+← | Reduce Effect Speed |
FN+→ | Increase Effect Speed |
WIRELESS CONNECTION
PAIRING WIRELESS 2.4GHz
- Power on the keyboard
- Short press FN+4 to enter 2.4G made
- FN+4 combination key 3S to enter pairing mode
- Insert the receiver, the indicator light flashes quickty
- After the pairing is successful, exit the code matching, and the mode light will always be on for 25
30s after the paired device is notfound, the exit code matching mode light goes out and the keyboard goes to sleepAfter the pairing is successful, let stand for 2 minutes to enter the light sleep state, andthe keyboard enters deep sleep after 10 minutes from entering the light sleep state
PAIRING BLUETOOTH
- Power on the keyboard
- Short press FN+1/2/3 key combination to enter Bluetooth mode
- Long press the FN+1/2/3 key combination for 3S, the keyboard enters the code matching state, and the indicator light flashes quickly
- Connected to the device, the indicator light is always on for 25
if the device is not connected, the indicator light goes out, and the keyboard goes to sleep After the pairing is successful, let it stand for 2 minutes to enter the light sleep state, and the keyboard enters deep sleep after 15 minutes from entering the light sleep state
BATTERY POWER
- The battery is below 10%, and the space flashes
- The space is always on during charging
- Restore the current backlight mode after full
PRODUCT SPECIFICATIONS
NUMBER OF KEYS | 87 KEYS |
---|---|
HOT-SWAP | YES |
BACKLIGHT | RGB BACKLIGHT |
CONNECTION | Type-C BT5.0 2.4G |
COMPATIBILITY | WINDOWS/MAC |
BATTERY | 2700mAh |
PRODUCT WEIGHT | 855G±20G |
PRODUCT DIMENSIONS | 360mm×135mm×28.5mm |
REPLACING KEYC APS AND SWITCHES
For a full guide on how to remove keycaps and switches scan the QR Code or
type in your browser:
Remove Switches
- Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
- Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
- Using firm but gentle force pull the switch away from the keyboard using a vertical motion.
Install Switches
- Check that all the switch metallic pins are perfectly straight and clean.
- Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
- Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
- Inspect the switch to ensure it’s properly attached to your keyboard, and test it.
Note: If the key doesn’t work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process. Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid damage to the keyboard due to operating errors.
TECHNICAL ASSISTANCE
For technical assistance, please email to
support@epomaker.com
with your purchase order number and a detailed description of your issue.
We normally respond to enquiries within 24 hours. If you purchased your
keyboard from a distributor or not from any official store of Epomaker, please
contact them directly for any additional help.
COMMUNITY FORUMS
Join our community and learn together with other keyboard enthusiasts.
https://discord.gg/2q3Z7C2
https://www.reddit.com/r/Epomaker/
WARRANTY
EPOMAKER’s Warranty covers any factory defects that might affect the proper
functionality of your purchase. It doesn’t cover any damage that may occur
from normal wear and tear. If your product is defective we will send you a
replacement unit. Replacement units might require you to send the defective
unit back to Epomaker.
We provide a 1 year warranty for our products when bought from our website
(EPOMAKER.com). Your item will not be covered by your 1 year warranty if the
inspection shows any sign of modification or changes unsupported by the
original product, these include: Changing internal components, Assembling and
reassembling the product, Replacing Batteries, etc.
We will ONLY cover the item if it is bought from our official stores. You do
not have a warranty with us if you bought the item from another reseller or
likewise. Please contact the store that you bought your product from to
resolve issues.
https://epomaker.com/pages/software-downloads
Made in China
Manufacturer: Shenzhen Changyun Technology Co., Ltd.
Address: Seventh Floor, Kai Daer Building, No.168 Tongsha Road,Xili Street,
Nanshan Disctrict, Shenzhen,Guangdong, CN
Email: support@epomaker.com
Web: www.epomaker.com
APEX CE SPECIALISTS LIMITED
Address: UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD
CORK, T23 AT2P, IRELAND
Contact : Wells
Tel: +353212066339
Email: info@apex-ce.com
References
- ce.com
- Epomaker
- Epomaker
- Epomaker
- DIY Guide: How to Replace Your Mechanical Keyboard Switches
- Software
- Reddit - Dive into anything
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>