EPOMAKER EP108 108-Keys Hot Swappable Wired-Wireless Mechanical Gaming Keyboard User Guide

EPOMAKER EP108 108-Keys Hot Swappable Wired-Wireless Mechanical Gaming Keyboard User Guide

WIN MODES

MAC MODES

CONNECTION MODE

Fn+  1 BT1
Fn+  2 BT2
Fn+  3BT3
Fn+  42.4G
Fn+  5Wired

RGB SETTINGS

Fn+Backspace  RGB Backlight On/Off

Fn+Ins            Change Backlight Effect

Fn+Home      Change Backlight Color

Fn+Del         Light Effect Direction

Fn+←→      Light Speed Adjustment

Fn+↑↓          Brightness Adjustment

SWITCH THE CONNECTED DEVICE

1. Short press Fn+1/2/3/4/5 to switch the device connection mode
2. The indicator light flashes slowly during the connection process of the device, and the indicator light stays on for 2s after the connection is successful
3. If the connection fails, the indicator light goes out and the keyboard sleeps

PAIRING BLUETOOTH

1. After the keyboard is turned on, press and hold Fn+1/2/3 until the
   indicator light flashes quickly to enter pairing mode

2. Find the KC108 BT3.0/5.0 on the bluetooth receiving device and pair it with it. After the pairing is completed, the indicator light is always on for 2s

3. If the pairing fails, the keyboard indicator turns off and goes to sleep, please re-pair

PAIRING WIRELESS 2.4GHz

1. Press and hold 4 until the pairing indicator flashes quickly to enter the 2.4G pairing mode
2. Insert the 2.4G receiver and place the keyboard as close to the 2.4G receiver as possible
3. After the code matching is successful, exit the code matching, the mode light is always on for 10s
4. If the code matching device is not found successfully, the indicator light turns off and goes to sleep after 30s, please perform the code matching operation again.

POWER SAVE MODE
When wirelessly connected (Bluetooth/2.4G), turn off the backlight without any operation for 5 minutes, and enter into deep sleep without operation for 30 minutes Press Fn+PGUP to enter the battery saving mode.

SPECIFICATION PARAMETER

KEYS AMOUNT: 108 Keys

KEYCAPS: PBT

HOTSWAP： YES

LIGHT: RGB

BATTERY CAPACITY: 6200mAh

CONNECTIVITY: Type-C Wired & Bluetooth Wireless

COMPATIBILITY: Windows/Mac

DIMENSION: 440mm×130mm×28mm

WEIGHT: 1030±20g

REP L A CIN G K E Y CAP S A N D S W I T C H E S

Push Straight Down

Please be gentle. Be sure the pins are aligned with the slots.

Included Tools

Remove Switches

1. Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
2. Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
3. Using firm but gentle force pull the switch away from the keyboard using a vertical motion

Install Switches

1. Check that all the switch metallic pins are perfectly straight and clean.
2. Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
3. Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
4. Inspect the switch to ensure it’s properly attached to your keyboard, and test it.

Note: If the key doesn’t work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process.

Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid damage to the keyboard due to operating errors

TECHNICAL ASSISTANCE

For technical assistance, please email to support@epomaker.com with your purchase order number and a detailed description of your issue. We normally respond to enquiries within 24 hours. If you purchased your keyboard from a distributor or not from any official store of Epomaker, please contact them directly for any additional help.

COMMUNITY FORUMS

Join our community and learn together with other keyboard enthusiasts.

 https://discord.gg/2q3Z7C2
 https://www.reddit.com/r/Epomaker/

WARRANTY
EPOMAKER’s Warranty covers any factory defects that might affect the proper functionality of your purchase. It doesn’t cover any damage that may occur from normal wear and tear. If your product is defective we will send you a replacement unit. Replacement units might require you to send the defective unit back to Epomaker. We provide a 1 year warranty for our products when bought from our website (EPOMAKER.com). Your item will not be covered by your 1 year warranty if the inspection shows any sign of modification or changes unsupported by the original product, these include: Changing internal components, Assembling and reassembling the product, Replacing Batteries, etc. We will ONLY cover the item if it is bought from our official stores. You do not have a warranty with us if you bought the item from another reseller or likewise. Please contact the store that you bought your product from to resolve issues.

Made in China
Manufacturer: Shenzhen Changyun Technology Co., Ltd.
Address: Seventh Floor, Kai Daer Building, No.168 Tongsha Road,
Xili Street, Nanshan Disctrict, Shenzhen,Guangdong, CN
Email:support@epomaker.com
Web:www.epomaker.com

References

• ce.com
• Epomaker
• Epomaker
• DIY Guide: How to Replace Your Mechanical Keyboard Switches
• Reddit - Dive into anything

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>