EPOMAKER EK68 Wired, Wireless RGB Mechanical Gaming Keyboard User Guide

EPOMAKER EK68 Wired, Wireless RGB Mechanical Gaming Keyboard

ABOUT COMPANY

• Manufacturer: Shenzhen Changyun Technology Co., Ltd.
• Address: Seventh Floor, Kai Daer Building, No.168 Tongsha Road,
• Xili Street, Nanshan Disctrict, Shenzhen,Guangdong, CN
• Email: support@epomaker.com
• Web: www.epomaker.com

SHORTCUT KEYS

CHANGE RGB EFFECTS

Press Fn+| to switch the RGB effects of your Epomaker EK68 keyboard.

PAIRING BLUETOOTH

Toggle the switch to make sure that the keyboard is under the Bluetooth mode:

1. Hold Fn+Q/W/E for 3-5 seconds till the indicators flashes fast in red/green/blue, the keyboard is ready to pair.
2. Turn on your Bluetooth device and find ‘BT Keyboard, then connect. When the keyboard is connected to the Bluetooth device, the light on the Q/W/E key stops flashing and the connection is done.
3. Press Fn+Q/W/E to toggle between the Bluetooth devices 1/2/3.

PAIRING WIRELESS 2.4GHz

1. Toggle the switch to 2.4G mode (the whole keyboard flashes red for three times when entering to the 2.4G mode), and then hold Fn+R for for 3-5 seconds till the light flashes fast in white, the keyboard is ready to pair.
2. Insert the 2.4G dongle to your device, the R key stops flashing white and the connection is done.

WIRED MODE

Toggle the switch to the wired mode, the whole keyboard flashes red three times, and the keyboard enters to the wired mode successfully.

SPECS

• KEYS AMOUNT: 66 keys + 1 knob
• STRUCTURE: Gasket-mount
• SHELL MATERIAL: Plastic
• PLATE MATERIAL PC
• STABILIZER TYPE: Plate-mounted
• PCB TYPE: 3/5-pin Hotswap PCB
• BATTERY CAPACITY: 3000mAh
• CONNECTIVITY: Type-C Wired, 2.4 & Bluetooth Wireless
• ANTI-GHOST KEY: NKRO in all modes
• COMPATIBILITY: WINDOWS/MAC
• DIMENSION: 325 x 117 x 41 mm
• WEIGHT: Around 0.8kg

REPLACING KEY CAPS AND SWITCHE S

For a full guide on how to remove keycaps and switches scan the QR Code or type in your browser: https://epomaker.com/blogs/guides/diy-guide-how-to- remove-and-replace-your-mechanical-keyboardswitches

Before installing switches, be sure the pins are clean and straight

Push Straight Down
Please be gentle. Be sure the pins are aligned with the slots

Included Tools

Mechanical Switch

Remove Switches

1. Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
2. Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
3. Using firm but gentle force pull the switch away from the keyboard using a vertical motion.

Install Switches

1. Check that all the switch metallic pins are perfectly straight and clean.
2. Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
3. Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
4. Inspect the switch to ensure it’s properly attached to your keyboard, and test it.

Note: If the key doesn’t work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process.
Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing
keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid
damage to the keyboard due to operating errors.

TECHNICAL ASSISTANCE

• For technical assistance, please email to support@epomaker.com with your purchase order number and a detailed description of your issue.
• We normally respond to enquiries within 24 hours. If you purchased your keyboard from a distributor or not from any official store of Epomaker, please contact them directly for any additional help.

COMMUNITY FORUMS

Join our community and learn together with other keyboard enthusiasts.

• https://discord.gg/2q3Z7c2
• https://www.reddit.com/r/Epomaker/

WARRANTY

• EPOMAKER’s Warranty covers any factory defects that might affect the proper functionality of your purchase. It doesn’t cover any damage that may occur from normal wear and tear. If your product is defective we will send you a replacement unit. Replacement units might require you to send the defective unit back to Epomaker.
• We provide a 1 year warranty for our products when bought from our website (EPOMAKER.com). Your item will not be covered by your 1 year warranty if the inspection shows any sign of modification or changes unsupported by the original product, these include: Changing internal components, Assembling and reassembling the product, Replacing Batteries, etc.
• We will ONLY COver the item if it is bought from our official stores. You do not have a warranty with us if you bought the item from another reseller or likewise. Please contact the store that you bought your product from to resolve issues.

References

• Epomaker
• Epomaker
• Reddit - Dive into anything

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>