EPOMAKER Dynatab 75X Gasket Mounted Mechanical Keyboard User Manual
- June 1, 2024
- EPOMAKER
Table of Contents
EPOMAKER Dynatab 75X Gasket Mounted Mechanical Keyboard User Manual
support@epomaker.com
www.epomaker.com
PAIRING BLUETOOTH
Toggle the switch make sure that the keyboard is under the Bluetooth mode:
- Hold Fn+Q/W /E for 3-5 seconds till the indicator flashes fast, the keyboard is ready to pair.
- Turn on your Bluetooth device and find the keyboard, then connect. When the keyboard is connected to the Bluetooth device, the light on the Q/W /E key stops flashing and the connection is done.
- Press Fn+ Q/W /E to toggle between the Bluetooth devices 1/2/3.
PAIRING WIRELESS 2.4GHZ
Toggle the switch to make sure that the keyboard is under the 2.4G mode:
- Hold Fn+R for for 3-5 seconds till the light flashes fast in green, the keyboard is ready to pair.
- Insert the 2.4G dongle to your device, when the R key stops flashing green, the connection is done.
Note: The keyboard will enter sleep mode after 2 minutes of inactivity, the keyboard lights go off, and it can be reactivated by any keypress.
WIRED MODE
Toggle the switch to the wired mode.
CHECK BATTERY
Hold Fn+Backspace, the keys from 1! to 0) lights up to show the battery percentage; for example, if the keys from 1! to 5• light up when holding Fn+B, it means that the battery life is currently 60%; if keys of 1!-0) light up, battery life is 100%.
Note: When the keyboard is at low battery, the battery indicator flashed red; when the keyboard is charging, the light stays green for 5s and goes off.
SPECS
REPLACING KEYCAPS AND SWITCHES
For a full guide on how to remove keycaps and switches scan the QR Code or
type in your browser:
Push Straight Down
Please be gentle. Be sure the pins are aligned with the slots.
Included Tools
Remove Switches
- Grab your Switch Removal Tool and align the gripping teeth vertically {on the Y-Axis) at the center of the switch, as shown in the example graphic above.
- Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
- Using firm but gentle force pull the switch away from the keyboard using a vertical motion.
Install Switches
- Check that all the switch metallic pins are perfectly straight and clean.
- Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
- Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
- Inspect the switch to ensure it’s properly attached to your keyboard, and test it.
(!) Note: If the key doesn’t work its possible you may have bent one of the
switches while installing it. Pull the switch out and repeat the process.
Pins may be damaged beyond repair and need replacement if this process is not
done correctly. Never apply excessive force when replacing keycaps or
switches. If you cannot remove or install keycaps or switches please contact
customer service as soon as possible to avoid damage to the keyboard due to
operating errors.
TECHNICAL ASSISTANCE
For technical assistance, please email to
support@epomaker.com with your purchase order
number and a detailed description of your issue.
We normally respond to enquiries within 24 hours. If you purchased your
keyboard from a distributor or not from any official store of Epomaker, please
contact them directly for any additional help.
COMMUNITY FORUMS
Join our community and learn together with other keyboard enthusiasts.
https://discord.gg/2q3Z7C2
https://www.reddit.com/r/EpomakerKeyboard/
WARRANTY
EPOMAKER’s Warranty covers any factory defects that might affect the proper
functionality of your purchase. It doesn’t cover any damage that may occur
from normal wear and tear.
If your product is defective we will send you a replacement unit. Replacement
units might require you to send the defective unit back to Epomaker.
We provide a 1 year warranty for our products when bought from our website {EPOMAKER.com). Your item will not be covered by your 1 year warranty if the inspection shows any sign of modification or changes unsupported by the original product, these include: Changing internal components, Assembling and reassembling the product, Replacing Batteries, etc.
We will ONLY cover the item if it is bought from our official stores. You do not have a warranty with us if you bought the item from another reseller or likewise. Please contact the store that you bought your product from to resolve issues.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>