SUPER BRIGHT LEDS LF-BL-A3 RGB CCT or Single Color Dimming Bluetooth Controller User Manual
- June 9, 2024
- super bright leds
Table of Contents
superbrightleds.com
RGB, CCT, or Single Color Dimming
Bluetooth Controller
User Manual
**Safety and Notes
**
- Product should be installed and serviced in accordance with applicable national, state, and local building and electrical codes.
- To reduce the risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures.
- Failure to properly secure controller, may result in damage or injury, for which the manufacturer does not assume responsibility.
- Intended for indoor use only.
- Auto-transmitting function relays signal to additional compatible controllers in 80 ft (25 m) range.
Controller Layout
The output mode indicator will be GREEN when in single color dimming mode,
BLUE when in CCT mode, and RED when in RGB mode.
To switch between modes, simply hold the set button until output mode
indicator changes color. Each time the mode on the controller is changed, the
controller will need to be re-paired with account on phone/tablet.
Wiring Diagram
Downloading the App
The app can be downloaded by scanning the QR code on iOS and Android or by
searching for “Open-Lit” in the Apple App store.
http://www.opuritech.com/APP.html
Phone/Tablet App Registration
- Ensure Bluetooth is enabled on the device.
- Open the app and select “Register” on the top right.
- Select an password and email combo for account, then press “Register” button.
- Return to home screen and log in.
Note: Controller can only be paired to one account at a time. However,
the same account can be used on multiple devices to access the same
controller.
Pairing Controller to Phone/Tablet
- Once logged in, and with device on the appropriate setting (RGB, CCT, or single color dimming), press “Add device” button.
- Select “Add Bluetooth device” option.
- A configuration screen will be displayed which will automatically pair the controller and the phone/tablet.
- Once the process is finished, app will return to the home screen, where the controller will now appear.
Note: Each time the mode on the controller is changed, the controller
will need to be re-paired with account on phone/tablet.
Renaming or Removing Controller
Once a controller is successfully paired, the name of the paired controller
can be changed by swiping to the left on the controller name and selecting
“rename” button. Select the delete option to unpair the controller from the
account.
Light Function
In RGB mode, “Light” screen will display 6 presets for white (RGB) at various brightness levels at the top. The large rectangle below the 6 presets is used to control RGB color by sliding a finger across it. A brightness control slider and a master on/off button are also located on this screen.
Light Function (cont.)
In CCT mode, there are 6 presets in a range from warm to cool which can be
selected. Similarly, in single color dimming mode there are 6 brightness
presets. A brightness control slider and a master on/off button are also
located on this screen.
Mode Selection
In RGB mode, “Mode” screen will display 6 presets and 4 programmable patterns. There is a slider to control brightness and speed at the bottom of the screen. In CCT mode, this screen features 7 preset patterns. In dimming mode, this screen features 3 preset patterns.
Mode Programming (RGB Mode only)
Each of the four programmable configurations in the “Mode” screen will allow
up to 6 RGB colors and one of three patterns to be used to create custom
modes.
Timing
Up to 16 on or off timer settings can be saved to automate controller
function. The controller will remain on the same setting it was using
previously when powered back on.
Mic (RGB Mode only)
When on the “Mic” screen the controller will use the microphone on the
connected phone/tablet and will activate lights based on any sound picked up
by microphone.
Specifications
| Model | LF-BL-A3 |
|---|---|
| Input Voltage Range | 9–24 VDC |
| Output Voltage Range* | 9–24 VDC |
| Max Input Current | 3 A (Barrel Connector) |
15 A (Screw Terminal)
Max Output Current| 15 A (5 A per channel max)
Operating Temperature| -22°–131° F (-30°–55° C)
Max Recommended Communication Distance (varies by device)| 80 ft (25 m)
Weight| 1.75 oz (50 g)
Documents / Resources
|
SUPER BRIGHT LEDS LF-BL-A3 RGB CCT or Single Color Dimming Bluetooth
Controller
[pdf] User Manual
LF-BL-A3 RGB CCT or Single Color Dimming Bluetooth Controller, LF-BL-A3, RGB
CCT or Single Color Dimming Bluetooth Controller, Single Color Dimming
Bluetooth Controller, Color Dimming Bluetooth Controller, Dimming Bluetooth
Controller, Bluetooth Controller, Controller
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>