NORDIC RG-B0118 18V Brushless Rivet Gun User Manual

NORDIC RG-B0118 18V Brushless Rivet Gun

PRODUCT SPECIFICATION

_& _4.8/5.0mm

Scope Of Riveting:| 0-5mm
Stroke Length:| 20mm

GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and instructions. Failure to heed warnings and follow instructions may result in electric shock, fire and/or serious injury. Keep safety warnings and instructions for future reference. The term “power tool” in the safety warnings refers to your mains operated (corded) power tool or battery- operated (cordless) power tool.

WORKING AREA

• Keep working area clean and well lit. Untidy and dark areas can lead to accidents.
• Do not operate power tools in potentially explosive surroundings, for example, in the presence of inflammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders at a distance when operating a power tool. Distractions can cause you to lose control of it.

ELECTRICAL SAFETY

• Always check that the power supply corresponds to the voltage on the rating plate.
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use adapter plugs with earthed power tools. Unmodified plugs and matching outlets will reduce the risk of an electric shock.
• Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and refrigerators. There is an increased risk of an electric shock if your body is earthed.
• Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will increase the risk of an electric shock.
• Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of an electric shock.
• When operating a power tool outdoors, use an extension cable suitable for outdoor use. Using a cord suitable for outdoor use reduces the risk of an electric shock.
• If operating a power tool in a damp location is unavoidable, use a power supply protected by a residual current device (RCD). Using an RCD reduces the risk of an electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or medication. A moment of inattention when operating a power tool may result in serious personal injury.
• Use safety equipment. Always wear eye protection. Using safety equipment such as a dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed will reduce the risk of personal injury.
• Avoid accidental starts. Ensure the switch is in the off position before inserting the plug. Carrying power tools with your finger on the switch or plugging in power tools when the switch is in the on position makes accidents more likely.
• Remove any adjusting keys or spanners before turning on the power tool. A spanner or key left attached to a rotating part of the power tool may result in personal injury.
• Do not reach out too far. Keep your feet firmly on the ground at all times. This will enable you retain control over the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from the power tool. Loose clothes, jewellery or long hair can become entangled in the moving parts..
• If there are devices for connecting dust extraction and collection facilities, please ensure that they are attached and used correctly. Using such devices can reduce dust-related hazards.

POWER TOOL USE AND CARE

• Do not expect the power tool to do more than it can. Use the correct power tool for what you want to do. A power tool will achieve better results and be safer if used in the context for which it was designed.
• Do not use the power tool if the switch cannot turn it on and off. A power tool with a broken switch is dangerous and must be repaired.
• Disconnect the plug from the power source before making adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store power tools, when not in use, out of the reach of children and do not allow people who are not familiar with the power tool or these instructions to operate it. Power tools are potentially dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or jammed moving parts, breakages or any other feature that might affect the operation of the power tool. If it is damaged, the power tool must be repaired. Many accidents are caused by using poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control.
• Use the power tool, accessories and cutting tools, etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work which needs to be done. Using a power tool in ways for which it was not intended can lead to potentially hazardous situations. Your power tool should be serviced by a qualified specialist using only standard spare parts. This will ensure that it meets the required safety standards.

Special safety instructions

• Always assume that the tool contains fasteners. Gripping the tool without proper attention may result in unexpected ejection of the fastener and injury.
• Do not point the tool until the tool is securely positioned on the workpiece. If the tool does not come into contact with the workpiece, the fastener may bounce off the destination.
• Disconnect the tool from the power supply if the fastener is jammed in the tool. When removing jammed fasteners, the tool can be activated accidentally if it is switched on.
• Be careful when removing jammed fasteners. The mechanism may be compressed and the fastener may be released with considerable force when removing the jam.
• Do no use the power cord attachment tool. The tool is not designed to install electrical cables and may damage the insulation of electrical cables causing a risk of electric shock or fire.

ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND CHARGERS.

Use only batteries and chargers applicable for this machine.

BATTERIES

• Never attempt to open for any reason.
• Do not store in locations where the temperature may exceed 40 °C.
• Charge only at ambient temperatures between 4 °C and 40 °C.
• When disposing of batteries, follow the instructions given in the section “Protecting the environment”.
• Do not cause short circuits. If connection is made between the positive (+) and negative (-) terminal directly or via accidental contact with metallic objects, the battery is short circuited and an intense current will flow causing heat generation which may lead to casing rupture or fire.
• Do not heat. If batteries are heated to above 100 °C, sealing and insulating separators and other polymer components may be damaged resulting in electrolyte leakage and/or internal short circuiting leading to heat generation causing rupture or file. Moreover do not dispose of the batteries in fire, explosion and/or intense burning may result.
• Under extreme conditions, battery leakage may occur. When you notice liquid on the battery, proceed as follows:
• Carefully wipe the liquid off using a cloth. Avoid skin contact.
• In case of skin or eye contact, follow the instructions below:

1. Immediately rinse with water. Neutralize with a mild acid such as lemon juice or vinegar.
2. In case of eye contact, rinse abundantly with clean water for at least 10 minutes.
3. Consult a physician.

Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do not incinerate the battery.

CHARGERS

• Never attempt to charge non-rechargeable batteries.
• Have defective cords replaced immediately.
• Do not expose to water.
• Do not open the charger.
• Do not probe the charger.
• The charger is intended for indoor use only.

SYMBOLS

In this manual and/or on the machine the following symbols are used:

• Denotes risk of personal injury or damage to the tool.
• Read manual before use
• Wear eye protection
• Wear ear protection
• Wear safety gloves
• Wear respiratory protection
• In accordance with essential requirements of the European directive(s)
• Class II – The machine is double insulated; Earthing wire is therefore not necessary (only for charger)
• Ambient temperature 40°C max. (only for battery)
• Do not expose charger and battery pack to water
• Use battery and charger only in closed rooms
• Do not incinerate battery pack or charger

CLEANING AND MAINTENANCE

CLEANING

• Keep the ventilation slots of the machine clean to prevent overheating of the engine.
• Regularly clean the machine housing with a soft cloth, preferably after each use.
• Keep the ventilation slots free from dust and dirt.
• If the dirt does not come off use a soft cloth moistened with soapy water.
• Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may damage the plastic parts.

MAINTENANCE
Our machines have been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper machine care and regular cleaning.

REPAIR

This product does not contain any parts that can be repaired by the consumer. Contact a qualified specialist to have it checked and repaired.

ENVIRONMENT

Should your appliance need replacement after extended use, do not dispose of it with the household refuse, but in an environmentally safe way. Waste produced by electrical machine items should not be handled like normal household rubbish. Please recycle where recycle facilities exist. Check you’re your Local Authority or retailer for recycling advice.

TOOL OPERATION

• Preparing for operation Before starting work, make sure that the container for broken rivet mandrels has been installed on the back of the housing. If it is not installed, install the empty container by sliding it into the seat on the back of the housing (V). Using corrensponding batteries with rated voltage and matching the tool battery socket. It is forbidden to modify the socket and/or battery to match them.
• Slide the charged battery into the guides of the battery socket so that the battery latch holds it in place (II). Check whether the battery does not slide out of the tool socket by itself.
• Installing the head net into the head. It is easier to installing if you press the switch.
• After installing the battery, the tool is ready to work.

RIVETER OPERATION

• The joined materials should be prepared by placing them on top of each other and then immobilizing them, e.g. with clamps, vice, etc. Make sure that the total thickness of the materials to be joined does not exceed the value given in the technical data sheet. The joined materials should adhere to each other as much as possible. If there is a rivet gap between the joined materials, the rivet cannot join both materials.

• Check the diameter of connection rivets. Drill the hole through both joined materials. The hole must be through with a diameter such as the diameter of the rivets to be used. When drilling is complete, make sure that the holes in both materials are aligned. Check that the rivet fi ts in the drilled holes. If possible, check that the rivet protrudes from both sides o f the joined materials.

• Slide the rivet into the hole of the riveting head so that its fl ange rests on the head nut (III).

• Slide the protruding part of the rivet into the hole drilled in the joined materials (IV). Press the head against the joined materials and press the riveter switch.
  Once you have riveted the materials and the rivet mandrel has been broken, release the pressure on the switch and move the riveter away from the joint. Make sure that the broken rivet mandrel is in the container. Point the riveter with the container down. After fi nishing work, disconnect the battery from the tool, remove broken mandrels from the container, pulling it out of the tool housing (V). Check the fi ll-up level of the container during operation and empty it if necessary. Next, proceed with the tool maintenance.

• Selection of riveting nut (VI) The riveter is equipped with different size riveting nut. This allows you to select the riveting nut according to the type and size of the rivets and the materials to be joined.

• Removing jams If during operation it is not possible to insert the rivet mandrel into the riveting head or broken mandrels will not be placed into the container, this may mean a jam. In this case, disconnect the battery from the tool by removing it from the socket and only then proceed to remove the jam.
  Warning! Removing a jam with the battery installed can result in unintentional starting of the tool, which can lead to serious injury. Unscrew the head housing with a wrench and disassemble it from the head (VII). Then unscrew the front of the head (VIII) and remove the jam. After removing the jam, assemble the head in the reverse order of disassembly.

• Head maintenance Warning! Maintenance of the head must be carried out when the battery is disconnected from the tool. Carrying out maintenance with the battery installed can result in unintentional starting of the tool, which can lead to serious injury. Disassemble the head according to the procedure in the section “Removing jams”. Clean each element of metal shavings and other impurities and then coat with a thin layer (so-called fi lm) of light machine oil. Assemble the head and clean the housing thoroughly from grease. Maintenance of the head should be carried out not less frequently than every 3000 clamped rivets. If excessively worn or damaged components are noticed during maintenance, replace them with new ones that are free of defects before continuing work.

Parts of Tool

1. head
2. power indicator
3. container for broken mandrels
4. power switch
5. handle
6. battery socket
7. wrench
8. head nut

INSTALLATION INSTRUCTION

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>