NORDIC HOME FT-543 Tower Coolers User Manual

NORDIC HOME FT-543 Tower Coolers

PART DESCRIPTION

1. Control panel
2. Adjust the angle (up and down)
3. Water level
4. Filter (honeycomb patterned)
5. Water tank
6. Water tank handle
7. Lid for water tank

Use

1. Place the product on a flat and even surface to keep it from tipping over and to avoid vibration noises.
2. Optional: Add prepared ice cubes or add an ice pack to the water tank to increase cooling effect.
3. Pull the water tank out about 2/3rds of its length and fill it with cold tap water. Do not overfill. Do not exceed the marked line in the water tank.
4. Make sure the water does not go below the lowest mark in the water tank to avoid damaging the water pump.
5. When the product is not in use. turn it off and disconnect it from the mains by pulling the plug. Do not pull the cable.

Buttons

• On/off button: press the button to turn the product on or off.
• Timer button: press the button to start a timer to turn off. 1h/2h/4h/8h.
• Mode button: press the button to change between normal, natural and sleep mode.
• Speed button: press the button to change between low, medium and high.
• Swing button: press the button to activate or deactivate swing/oscillation, left to right. Up and down adjustment is manual.
• Cold button (air cooler/vapor): press the button to activate or deactivate the humidification function. Which helps with cooling.

Cleaning and maintenance

• Clean the surface of the product with a soft moist cloth and mild detergent.
• Clean the water tank with a brush or a sponge with a mild detergent.
• Rinse it with water. The filter can be cleaned with a neutral detergent and soft brush. Do not clean the filter in the washing machine.
• The water tank should be cleaned occasionally to prevent potential bacteria spread.
• When the product will not be used for a long time, the water tank should be cleaned.
• Make sure the water tank is empty and the product is completely dry before storage.
• Use a plastic bag or the package to store the product dark and dry.

Remove water tank

Warning electrical hazard: Disconnect the device from power before starting any maintenance.
Optional: If the water tank is full of water, this might feel more difficult then it needs to be.

We recommend that you try to empty some water first, for example with a cup or if you happen to have a rubber hose or similar then you can use that or tipping it carefully where you have a floor drain.

1. Unlock the water tank
2. Pull the water tank out to about 2/3rds of its length.
3. Optional: Remove the ice packs (depends on if there are ice packs in the water tank).
4. Move the plastic clip away from the water pump (You can now skip to step 8).
5. Optional step: Unscrew the screw (this step can be skipped completely).
6. Optional: lift and remove the plastic clip. You can now see the rubber ring.
7. Optional: Remove the rubber ring.
8. Lift out the water pump.
9. Hold the water pump with 1 hand (do not disconnect the cable or water pipe), and with the other hand wiggle out the water tank. Keep wiggling until the water tank is fully out.
10. The water tank is out. Clean it.
11. For putting the water tank back to its place, follow the steps in reverse, but when you hold the water pump, try to match the cable and water pipe with the matching hole

Detail of the matching hole.

Safety instructions

1. If the power cord or plug is damaged, have it replaced by qualified personnel.
2. To protect against electrical shock; do not immerse the device, cord and/or plug into water or other liquid.
3. This device can be used by children 8 years and above, people with disabilities or lack of experience and knowledge if they are kept under supervision or given instructions concerning the use of the device in a safe way and that they understand the risks. Children should not play with the device. Cleaning and maintenance should not be done by children without supervision.
4. Unplug the device from the mains outlet when not in use and before cleaning.
5. Keep electrical appliances out of reach of children or debilitated persons. Do not let them use the device without supervision.
6. Disconnect the fan from the mains when moving it from one place to another.
7. Be sure that the fan is standing on a stable surface when you use it, to avoid tipping it over.
8. If the fan tips over during operation, turn the device off and unplug it from the mains immediately.
9. Do not use the fan near the window, rain may create an electrical hazard.
10. For indoor use only.
11. The wall socket must continue to be easily accessible after the appliance is plugged in.
12. To unplug: only pull the plug, never pull on the cable to avoid damage.
13. Do not wind the cable around the appliance and do not bend the cable.
14. Do not use abrasive cleaners or solvents to prevent scratching the surface. Do not use any of the following as a cleaner: gasoline, or thinning solvent.
15. Do not use in wet areas such as bathrooms and swimming pools. And do not use in high temperature areas (over 40°C). Do not use in dusty environments.
16. Do not use near fire or combustible materials.

Troubleshooting

• Problem: Vibration noises.
  Possible solutions: When the humidification function starts, it produces some vibration noise. It also produces vibration noise when it has too little water because the water pump gets filled with air and starts to vibrate. Fill the water tank with water to stop the noises.

• Problem: Water turns yellow.
  Possible solutions: When the using the humidification function the first time and some uses after the water might change to yellow. This is normal. And it will stop happening automatically after some uses.

• Problem: The product does not work or does not start.
  Possible solutions: The power cable is not connected or is poorly connected. Ensure the power cable is well connected. The power button has not been pressed. Press the power button to turn it on.

• Problem: Low air flow.
  Possible solutions: The filter is filled with dust or dirt. Remove and clean the filter. The air inlet is blocked by an object. Remove the object from the air inlet.

• Problem: The pump is working but the humidification function is not working.
  Possible solutions: The water level in the water tank is too low. Add water to the water tank.

Features
Power: 230V; 50Hz, 110W effect

Support

More product information can be found at www.deltaco.eu

Email: help@deltaco.eu

References

• aurdel.com/compliance/
• deltaco.eu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>